Search Documents

By N. S. Stoloff, R. G. Davis

It is concluded from an X-ray stztdy that the formation of the hcp Mg3Cd superlattice is a nuclea-tion and growth reaction. A two-phase, ordered-plus-disordered, region is observed between 153" nnd 141"C. A maximum in the flow stress is observed both at temperature and in quenched specimens within the two-phase region. The peak arises fro112 the extra energy required to create antiphase boundary upon cutting the ordered regions. Hardening during isothermal annealing in Mg3Cd has been shown to be similar to the domain hardening in Cu3Au-type alloys in that up to the maximum the structure is ordered domains growing into a short range ordered matrix. The hardening is due to a combination of short range order strengthening and the strengthening produced when antiphase boundary has to be created. In a recent study1 of the effect of long-range order upon the mechanical properties and deformation modes of hcp Mg3Cd a comparison was made be- tween quenched (disordered) and slow-cooled (fully ordered) specimens. The most striking observations were that the disordered alloy yields at a much higher stress than the ordered alloy, and that there is a change in slip mode from primarily (_0001) ba_sal slip in the disordered state to (0001), {1010}, {1122}, and {l011} slip in the ordered state. The main purpose of the present work is to extend these observations to determine whether MgsCd exhibits a peak in flow stress at an intermediate degree of order, or at a critical domain size, as do other orderedstems. However, disagreement exists about the Mg3Cd order transformation with respect to: 1) the location of the critical temperature for order, 165°C or 153"~,' and 2) how the degree of order varies with temperature. Welber et a1.5 concluded from specific heat measurements that the formation of Mg3Cd is a second-order reaction with the degree of order a continuous function of temperature, while Moore and Raynor concluded that it is neither a first-order reaction, with the degree of order a discontinuous function of temperature, nor a second-order reaction. Consequently it was considered necessary to undertake an X-ray investigation into the change in degree of order and structure in the

Jan 1, 1964

By C. E. Birchenall, R. H. Condit

THREE surface activity procedures are in com--L mon use for the determination of diffusion coefficients in solids. In the oldest of these' the activity observed at the original surface is compared before and after diffusion, where all the activity is in a thin, plated layer on the surface before diffusion. Partial absorption of the radiations from active atoms which have diffused below the surface reduces the effective activity after diffusion. The formula employed to calculate the diffusion coefficient is where F, is the ratio of final to initial activity at the surface, measured with identical counting geometry; Z=u3Dt, where D is the diffusion coefficient; t is the diffusion time; and u is the absorption coefficient for the radiation in the solid as defined by Lambert's law. This absorption law implies that all the rays are parallel to each other and normal to the specimen surface. This assumption of a collimated beam used by Steigman, Shockley, and Nix has been adopted by all other investigators and, although it gives results which are approximately correct under restricted physical conditions, it does not represent many actual circumstances. It is the purpose of this paper to show the importance of the divergent rays and to indicate a procedure for taking them into account. In the residual activity method the activity is determined on a series of surfaces ground on the specimen at progressively greater depths in the diffusion layer parallel to the initial surface. Gruzin2 has de- rived a formula for this procedure, which may be put in the form where I is the ratio of the activity measured at a newly ground surface at distance k below the initial surface to the activity at the initial surface measured after diffusion, and K= k/2p Dt. A third procedure involves the autoradio-graphic determination of activity on a plane ground at a small angle to the initial interface through the penetration zone. Aut oradiography can be particularly sensitive to the oblique rays. Unlike most counters which detect essentially all ß particles or X-rays which enter the active volume as a single event, the photographic emulsion may be thin enough so that oblique rays with longer path length in the emulsion produce more darkening than rays which move normal to the film plane. Consider a plane containing a source of radiation uniformly spread over a circle and a point counter located on the perpendicular through the center of the circle. As the counter moves along this line, the total angle 6, at the counter subtended by the specimen will vary. For a fixed counter distance, let 6 be angle between the counter axis and the line connecting the counter to a point P on the active plane. If an absorber of thickness X is interposed parallel to the source between counter and source, the ray from point P to the counter will pass through an absorber thickness X secant 6. Exponential absorption is assumed to hold for all rays. If r, is the ratio of intensity at the counter with absorber to the intensity without absorber and a = pX, 1 00 The behavior of this integral, evaluated numerically,

Jan 1, 1957

By A. CHESTER BEATTY

SO much has been written about African, and particularly about Northern Rhodesian, copper during the past two years that I feel safe in assuming that you are familiar with the general background of the Rhodesian picture. Therefore, I will confine myself to certain of the high lights in connection with the history, geology, development, ore reserves, and contemplated mining methods in this relatively new and highly important copper field., Unlike most of the other great orebodies of the world, the Roan Antelope mine was not discovered by the hoof of a starving prospector's faithful burro; nor even, as its name might suggest, by a well-placed kick of protest from an antelope stumbling over a malachite outcrop. Late in 1905 an English prospector named Collier, traveling in the N'Dola district, came upon some natives using a green powder for medicinal purposes. Closer examination of the powder revealed that it ' was ground-up malachite. Collier endeavored to persuade the natives to tell him where they obtained this medicine, but' for a long time without success, because of the general feeling among the natives that they did not wish to reveal the resources of their land to the white. Finally however, - he persuaded- brie 'of-the elders to at" least take 'him part way toward, the- place where the malachite was supposed to occur. The bid took him, to a point on the lower regions of the Luanshya river and there left him with the instructions that if he followed the stream up toward its.

Jan 1, 1931

By Samuel D. Warriner

(Wilkes-Barre Meeting, June, 1911.) THE dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has- been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able not only to reach decisions based upon the merits of the controversies, but to enforce its decisions upon both the employees and the employers. It has never been obliged to shape its conduct to secure the consent of the contending parties, and its decisions have been strictly and, in the main, cheerfully observed. The remarkable feature of this board has been that it has

Aug 1, 1911

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10' cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.' This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.'-= At the same time, the material shows considerable ductility.3'4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin's relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1' presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.'3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella's reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With' elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By A. P. Young, F. C. Holden

IN many of the early investigations of the aging of titanium alloys, it was observed that the retained beta phase could be aged to a high hardness without an apparent change in microstructure; moreover, in some alloys it was found that even a very rapid quench produced beta having an anomalously high hardness. What appeared to be hard beta phase was designated as "beta prime," to distinguish it from the softer normal retained beta phase. Frost and co-workers'.' demonstrated that the increased hardness is caused by the formation of a metastable phase, omega, which can be identified from its X-ray diffraction pattern. This reaction also has been studied by Brotzen, et a1.,3 and the structure of the omega phase has been published by Silcock, et al.," and by Austin and Doig.3 The X-ray diffraction analysis by Austin and Doig indicated that omega is low in alloy content, approaching the composition of the stable alpha. The aging process proceeds by the path Thus, overaging results in the formation of alpha and the ultimate disappearance of omega. This is accompanied by a decrease in hardness and a recovery of ductility. The present work represents a study of the aging process in a high-purity Ti-6.4 Mn alloy, in which optical and electron microscopy, X-ray diffraction, and hardness data were correlated. The specimens, 1/8-in. sections cut from 1/4-in.-diam rod, were heated in argon to a temperature just into the beta field (810°C), held for 1 hr, and water-quenched. The aging samples were heated in air for 1 hr at 300 to 500°C. The specimens were ground and mechanically polished, finishing with alternate etching and polishing on a slow-speed wheel to remove disturbed metal from the surface. The surface finally was swab-etched, rinsed with tap water, and air-dried. The etchant used was an aqueous solution containing 1 1/2 pct HF and 3 1/2 pct HNO3. This procedure is identical with that used for preparing metallographic specimens, except that the optimum degree of final etching required for electron microscopy may vary from that used for light microscopy. Metal replicas, backed with silica, were prepared from plastic strip-pings for examination with the electron microscope. Complete details of the procedures used for preparing these replicas are available elsewhere." Fig. 1 shows a comparison between the structures revealed by the electron microscope and those obtained by conventional light microscopy. Hardness and X-ray diffraction data are listed in Table I. No evidence of a second phase is apparent in the optical micrographs for the as-quenched sample, or for the specimens aged at 300 or 400°C; fine alpha particles can be seen in the specimen aged at 500°C. In the electron micrographs, visible equiaxed pocks appear in the as-quenched specimen, and, with increasing density, in the samples aged at 300 and 400°C. After aging at 500°C, the structure becomes markedly coarser and develops an oriented appearance of a second phase, coincident with the appearance of visible alpha particles in the light micrographs. These observations are confirmed by X-ray diffraction and hardness data. In these specimens, aged for 1 hr, the intensity of the omega pattern increases to a maximum at the 400°C aging temperature, corresponding to maximum hardness and the maximum density of pocks in the electron micrographs. At this point the beta phase shows a definite enrichment in Mn. At 500°C, little or no omega re-

Jan 1, 1959

By Peter Soo

Pvestrained Ferrovac E iron has been neutron-irradiated at approximately 90°C to an integrated flux of 1020 nut (E > 0.82 mev]. The irradiation was found to produce an incveased temperature dependence of the flow stress in addition to a greatly increased athemal stress. Measurements of the flow stress and stress relaxation, from which the activation volume and activation energy for slip were deduced, show that neutron irradiation changes the rate -controlling slip process to one based on dislocation interactions with tetragonal distortions which are Produced around submicroscopic interstitial loops in the lattice. The study indicates that without prestraining prior to irradiation the chances of detecting a change in the rate -controlling slip process are greatly reduced because in the initial stages of slip a substantial fraction of the radiation defects are swept out of the slip plane by gliding dislocations. Thus, activation parameters which are subsequently measured are representative of a greatly reduced defect density and would not differ appreciably from those for unirradi-ated material. The large increase in the athermal component of the flow stress is probably connected with the presence of depleted zones in the lattice which are introduced by irradiation. ALTHOUGH fast neutron-irradiation has not been observed to markedly alter the activation parameters for slip in bcc metals,' small but significant changes do occur. Most experimenters agree that irradiation predominantly increases the athermal component of the yield stress.'-= In addition to this, Laidler and smidt7 have shown that in iron irradiated to 5 X 10" nvt and molybdenum irradiated to 10" nvt, changes occur in the activation volumes for slip. A similar conclusion has been reached by Milasin and Malkin8 for irradiated iron. Work by Ohr et a1.5 shows that for Ferrovac E iron, irradiated to 1.2 X 1016 nvt, small increases in the activation energy for slip also occur. So far these changes in the activation parameters have not been explained on a firm theoretical basis. One important factor which would minimize the chances of detecting a change in the slip mechanism upon irradiation is the presence of "channeling" which has been observed in molybdenum,9 niobium,10 and iron.11These channels are formed by gliding dislocations which sweep irradiation defects out of the active slip planes and thereby create zones in which continued dislocation motion is encouraged. The activation parameters for the dislocations gliding in the defect-free channels would, therefore, be similar to those for unirradiated iron and a change in the rate-controlling slip process would be difficult to detect. In the present work, an attempt has been made to reduce the effect of uneven deformation on the measured activation parameters for slip in neutron-irradiated Ferrovac E iron polycrystals, so that a more realistic assessment of the effects of neutron-irradiation could be made. Primarily, the experiments involve the irradiation of specimens which had been prestrained to 9 pct elongation at room temperature prior to insertion into the reactor. It was hoped that the introduction of a large number of evenly distributed dislocations would substantially decrease any channeling effect which might otherwise occur. MATERIAL AND EXPERIMENTAL PROCEDURE The starting material was vacuum-melted Ferrovac E iron, an analysis of which is given in Table I. The standard tensile specimen had a gage length of 1.125 in., a cross-sectional diameter of 0.120 in., and a re-crystallized grain size of 1.2 x 10-3 in. All tensile tests were conducted on a floor model "Instron" tensile machine at a strain rate of 3 x 10-4 per sec. The irradiation of the prestrained specimens was performed in the Brookhaven High Flux Beam Reactor to an integrated flux of 1020 nvt (E > 0.82 mev) at a temperature of about 90°C. All specimens were excap-sulated in high-purity aluminum sheaths which were lightly swaged around the samples to ensure good thermal contact. Subsequent measurements on the irradiated specimens showed that within experimental accuracy the swaging had not deformed them. EXPERIMENTAL RESULTS Fig. 1 shows the flow stresses for a series of unirradiated control samples. In order to produce a comparable dislocation substructure throughout the test sm range, all specimens were prestrained

Jan 1, 1970

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

By R. Maddin, W. R. Hibbard

A series of X ray experiments conducted by G. I. Taylor' in 1927 and later substantiated in 1939 by J. A. Collins2 both on axially strained aluminum single crystals, revealed evidence that during single slip crystallite rotation occurs in such a manner that " all parts of the material rotated about the transverse direction in the plane of slip."l The actual method of preparing the specimens for X ray examination is not discussed in detail by Taylor except to say that "this specimen was cut parallel to the plane of slip, as calculated from measurements of marks in the surface of the specimen. It was ground and etched till the effect of the new cuts had disappeared. This was verified by applying the same treatment to an un-distorted specimen. The X ray reflectionsl in this case were perfect ones."' Collins, on the other hand, cut his crystals in a mechanical shaper. These surfaces were polished on No. 1, No. 1/0, No. 2/0 and No. 3/0 papers and on a broadcloth lap using No. 600 alundum as a polishing medium. "Finally, the surface was deeply etched in Tucker's reagent. An unde-formed crystal was prepared in the manner described and X rayed to determine whether or not the machining and polishing operations had produced any strain or distortion in the crystal. The Laue spots all seem to be sharp, free from tails and streaks indicating no detectable strains had been introduced in the crystals." Taylor's X ray technique involved the use of "homogeneous X rays from an iron anti-cathode"; whereas Collins used Ka radiation of copper at 31kv and 20 milliamperes. Glancing angle X ray photograms were taken (1) with the axis of rotation of the spectrometer table in the plane of slip and at right angles to the slip direction, and (2) with the axis of the spectrometer table lying along the slip direction. However, eight minute exposures were used in each case and the angle setting of the spectrometer table was increased by one degree for each exposure. With the discovery of the action of three slip systems3 in the plastic deformation of single crystalline alpha brass where, formerly, only one had

Jan 1, 1950

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951

By Arthur Knapp

OIL-WELL depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. DATA FOR LEASE STATUS-TIME OR DOLLARS-TIME CURVE TIME LEASE MONTHS STATUS Lease purchased for $3000 0 -$ 3,000 No expenses chargeable to lease for 3 mo 2 - 3,000 Well A is started; cost of drilling for month is $16,000 3 - 19,000 Well is completed at additional cost of $10,000 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (see Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.: difference between expenditures and receipts gives profit for month of $5,000 5 - 24,000 Investment is small, cost of operating well A is small, so profits are $15,000 6 - 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000.... 7 - 5,000 Lease operation now becomes normal and curve becomes smooth 8 - 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000

Jan 1, 1921

By A. B. Parsons

DOWN in Washington an army of individuals constituting the government of a so-called "'democratic" nation is trying to manage the conduct, in its rnultifold phases, of the greatest war in history for the country that is potentially, at least, the strongest in the world and on which, consequently, the major responsibility rests. The enterprise is one of unprecedented magnitude and complexity. That individuals and groups have made and are making serious blunders, both as to the establishment and execution of policy, is to be expected.

Jan 1, 1942

By R. Taggart, R. H. Ericksen, D. H. Polonis

Transmission electron microscopy techniques hare been used to study the spontaneous marfensite phase that forms during the thinning of Ti-Cr alloys. The structure of this phase has been found to differ. from the hcp martensite and has been identified as a clisforted fcc lattice. The spordaneous marlensile in this system is interpreted as a metastable isomorph of the equilibriunz TiCr, phase. WHEN thin-foil specimens for transmission electron microscopy were prepared from metastable alloys of the Ti-Cr system, a spontaneous transformation occurred' when the foils contained the untrans-formed 0 phase or two-phase mixtures of the 0 and w phases. The purpose of this paper is to examine the relationship that exists between the crystal structure of the spontaneous product and that of the matrix. The differences between the martensite transformation that occurs in the bulk material and the spontaneous reaction that occurs during the preparation of thin foils are compared with the observations that have been reported for similar phenomena in a commercial titanium alloy.' A spontaneous reaction that exhibits characteristics similar to a martensite transformation has been reported to occur in thin foils prepared from the retained metastable structures of several alloy systems.1'3"7 ~ull~ observed such a spontaneous reaction in 0 brass and attributed the apparent increase in the martensite transformation temperature to a decrease in the non-chemical free energy associated with bulk strain energy. He also showed that the spontaneous product did not have a specific habit plane, but that its orientation relationships to the parent matrix were dependen on the thickness of the transforming region. It has also been pointed out by Breedis6 that in thin films the absence of the constraints imposed by a bulk matrix can cause different requirements for the martensite plate interface and lattice distortion which is reflected bv a dependence of the transformation mechanism on the specimen geometry. In the case of the spontaneous reaction reported for Au-Zn alloys7 a definite habit plane was determined and shown to correspond with the habit plane calculated on the basis of the Bowles and Mackenzie crystallographic theory of the martensite transformation.'- lo EXPERIMENTAL PROCEDURE A series of titanium alloys containing 5.5, 5.9, 6.4: 7.6, 8.0, 11.3, and 18.7 at. pct Cr were prepared from high-purity (iochrome) chromium and iodide-grade titanium by levitation melting. The experimental procedure used for sectioning the alloys and for thin-foil preparation has been reported in an earlier paper.' X-ray diffraction patterns were obtained using a 114-mm Debye-Scherrer camera and Cu-Ka radiation. In order to minimize fluorescent radiation from the specimen, a strip of aluminum foil 0.002 in. thick was placed in contact with the X-ray film. After a specimen was removed from the camera: an additional X-ray experiment was performed, to insure that no spurious lines were obtained due to the presence of the aluminum foil. The interstitial impurity analysis for the alloys used in this study was as follows: oxygen, 100 ppm: hydrogen, 30 ppm: nitrogen, 28 ppm. EXPERIMENTAL RESULTS Electron diffraction patterns were obtained from several individual crystals of the spontaneous marten-

Jan 1, 1970

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By CYRIL W., William Campbell, Henry M. Howe

THIS paper gives the results of an investigation of the behavior of the argentiferous cobalt-nickel arsenides of Temiskaming, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines, of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr. E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. OBJECT OF THE INVESTIGATION. The object of the investigation was to learn:- 1. The temperature at which the arsenic is most rapidly expelled; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at the beginning of the roast. II. NATURE OF THE ORE. The important ores mined in the Temiskaming deposits are native silver-with small amounts of dyscrasite (Ag6 Sb), argentite (Ag2S), pyrargyrite (Ag3SbS3)-smaltite (CoAs2), chloanthite (NiAs2) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 -was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent ; nickel, from 3 to 4.7 per cent ; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite ; In our laboratory-work

Jan 1, 1907

THE CHAIRMAN.- This meeting is under the auspices of the American Institute of Mining and Metallurgical Engineers, and I think the germ of the idea originated in the steel business. Last year there was a meeting of prominent people in the steel industry with the idea of getting together and discussing practical phases of their business, so that everybody could contribute and from that there might be benefit derived for the industry. Several months ago when Mr. Bain was in Salt Lake City, he and Mr. Oldright asked me what I, as an individual, thought of it. From that originated this idea of having the copper people come together to discuss reverberatory smelting and all its phases. In starting out, it seemed the best plan to ask members what particular subjects they wished to discuss first; that is, the ones that would be considered more important. We asked Mr. Oldright, or suggested sometime ago that the meeting be postponed until May because May is a lovely month in Salt Lake. There are a number of attractive features around the city. We have a number of smelters here and I think that probably the most of the benefit will be derived from talking in an informal way and visiting the various plants around. the valley. At any rate, speaking as a resident of Salt Lake, I am glad to see all of you gentlemen here, and hope you have an interesting and instructive time. The tentative list of subjects for discussion at this conference is as follows: Construction Walls, etc. Walls, proper design and thickness of brick for various types of charging. Bottoms, construction of. Binding steel, correct weight and arrangement, where thrust of arch should be taken. Refractory materials, feasibility of using different material in various parts of the furnace. Water jackets, where applicable. Should bricks be used inside of same. Gas space, proper design for, height of roof above bath, etc. Roof Shape of Roof, in hot zone and elsewhere, longitudinally. Construction of roof, in various zones, around openings.

Jan 1, 1930

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955