Search Documents

By Robert Abbott

THE influence of various elements in retarding or accelerating the absorption of carbon during the process of carburization is fairly well known. In general those elements which forth carbides accelerate the absorption, while those which do not retard it. It has sometimes been wrongly stated that those elements which raise the temperature of the critical range increase the absorption, while those which lower this temperature decrease it. Silicon is a notable exception to this rule, for its influence is to raise the critical range but to lower the absorption of carbon. Some elements which do not form carbides have no apparent influence upon the absorption rate. Carbon itself retards the absorption rate. With a view to obtaining more exact data upon the subject the following experiments were undertaken : 208 steels of different chemical composition were selected to represent most of the types of modern constructional steels. Specimens 3 in. in diameter and in. in length were weighed to milligrams. They were then packed in the special carburizing box shown in Fig. 1, and kept in .the furnace for 10 hours at a temperature of 900° C. A duplicate experiment was conducted at 1,000° C. At equal' intervals of time the box was rotated in the furnace so that. two complete revolutions were made in the 10 hours. This precaution was taken to neutralize as much as possible any effect of unequal heating. At the end of the 10 hours the box was allowed to cool in the furnace with the doors open. The specimens were then weighed again and the increased weight (carbon) determined. In. the following table are given the analyses of the various steels, together with the. increased weight of .carbon expressed in milligrams.

Jan 10, 1913

By Joseph Singewald

I. THE GENESIS OF THE DEPOSITS THE ore deposits at Firmeza have been worked continuously since 1884; those at Daiquiri since 1895. It is surprising, therefore, that they have not been the object of careful geologic study until quite recently. It is true that considerable attention was paid to these deposits by A. C. Spencer, in 1901, in the report on the geology of Cuba, by Hayes, Vaughan, and Spencer,1 but this was only incidental to a hasty general reconnaissance of the Island. As far as the Daiquiri deposits are concerned, this gap has been filled by the appearance of the two papers by Prof. James F. Kemp2 and by Prof. Waldemar Lindgren and Clyde P. Ross respectively.3 Max Roesler, first holder of the Emmons fellowship, made a detailed study of the Firmeza deposits during the past summer, so that soon we can expect a full description of them. Consequently, there is no. demand at the present time for a description of the deposits from other sources, rind that is not the purpose of this paper. The papers on Daiquiri, however, leave unsolved problems in regard to the age of the rocks of the district and certain phases of the genesis of the deposits, and it is with the. hope of aiding in the solution of some of these problems that this contribution is offered. Kemp, and Lindgren and Ross agree in assigning these deposits to the type of contact metamorphic deposits. They disagree in part on the question of their localization. The deposits occur in an extensive area of diorite which includes numerous blocks of limestone, and some-

Jan 3, 1916

By J. M. Hartman

ONE of the most important subjects to the blast-furnace engineer is a thorough knowledge of the conditions affecting the temperature in the different portions of the furnace. All efforts to decrease the consumption of fuel and improve the working of the furnace must be based upon it, and I may, therefore, be permitted to place before you the results of my observations, and detail the conclusions to which they have led me. Tracing the thermic conditions from below upwards we have at the bottom of a blast furnace making No. 3 iron a temperature of 2900' F., which increases slightly to a point a little below the tuyeres. In the immediate vicinity of the tuyeres the temperature is somewhat lower, owing to the entering blast; but a short distance above the tuyeres, where all the oxygen of the blast has been converted into carbonic acid, the highest temperature in the furnace must be attained. This carbonic acid is, however, almost as soon as formed, converted by the glowing coal into carbonic oxide, a process which absorb, heat, reduces the temperature, and provides the active agent for the reduction of the iron ores. In its ascent the hot carbonic oxide gradually parts with its heat, first melting the descending iron and earthy materials, which drop down to the hearth of the furnace. The limit of this zone of fusion is rather sharply defined, and the temperature above this zone suddenly decreases. In its further ascent the hot gas drives off the carbonic acid from the limestone, which causes a further absorption of heat, and finally the gas escapes at the top, at a ternperature of about 250' F. if the furnace is working well. These changes of temperature I have attempted to represent graphically,

Jan 1, 1880

By J. M. Hartman

ONE of the most important subjects to the blast-furnace engineer is a thorough knowledge of the conditions affecting the temperature in the different portions of the furnace. All efforts to decrease the consumption of fuel and improve the working of the furnace must be based upon it, and I may, therefore, be permitted to place before you the results of my observations, and detail the conclusions to which they have led me. Tracing the thermic conditions from below upwards we have at the bottom of a blast furnace making No. 3 iron a temperature of 2900° F., which increases slightly to a point a little below the tuyeres. In the immediate vicinity of the tuyeres the temperature is somewhat lower, owing to the entering blast ; but a short distance above the tuyeres, where all the oxygen of the blast has been converted into carbonic acid, the highest temperature in the furnace must be attained. This carbonic acid is, however, almost as soon as formed, converted by the glowing coal into carbonic oxide, a process which absorbs heat, reduces the temperature, and provides the active agent for the reduction of the iron ores. In its ascent the hot carbonic oxide gradually parts with its heat, first melting the descending iron and earthy materials, which drop down to the hearth of the furnace. The limit of this zone of fusion is rather sharply defined, and the temperature above this zone suddenly decreases. In its further ascent the hot gas drives off the carbonic acid from the limestone, which causes a further absorption of heat, and finally the gas escapes at the top, at a temperature of about 250° F. if the furnace is working well. These changes of temperature 1 have attempted to represent graphically,

Jan 1, 1880

By George Hunt

THE first practical treatment of wood to prevent decay was devised early in the 19th century. At that time the oaken navy of England, when the nation was fighting for its very existence, seemed doomed to annihilation by the swift ravages of decay. The acute situation inspired a desperate search for preventive measures and resulted in the development of the Burnett, Bethel and Kyan processes for impregnating wood with zinc chloride, coal-tar creosote and mercuric chloride, respectively. In the century that has elapsed, their use has spread throughout the world and the three original preservatives are used today in enormous quantities. Meanwhile, improved processes have been developed, new preservatives discovered, and the practice of impregnating wood to make it last longer has attained a position of major importance in the field of structural materials. USE OF PRESERVATIVES BY THE RAILROADS In the application of wood preservatives in the United States the railroads have been the leaders for the past 50 years or more. Having found that decay is the chief cause of the early destruction of wood and that preservative treatment is the remedy, they have treated their ties and timber in increasing amounts(1)?-in 1925 about 220;000,000 cubic feet. By preservative treatment the Santa Fe Railroad saves annually 1,500,000 ties in its 18,000 miles of track, and many other railroads effect similar savings. (2) In like manner the life of wooden bridges and trestles,(3) poles, marine piling, water tanks and other wooden railroad structures has been greatly increased, reducing the amount of timber required annually to maintain them.(5),(7)

Jan 1, 1927

Organization. Place Date 1915 American Institute of Mining Engineers New York, N. Y. Feb.18-21 National Society for Promotion of Industrial Educa- tion New York, N. Y. Feb. American Institute of Architects.... Washington, D. C. April American Iron and Steel Institute New York, N. I? May New York Electrical Society: New York, N.. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept.9-13 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic City, N. J. Sept.

Jan 2, 1918

By Frederic P. Dewey

It is common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupella-tion, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy' says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 ays that at a proper temperature no silver is lost by volatilization. Primarily, excessive temperature may be due to too high general temperature in the muffle; but it may often be due to temperature localized within the bead by oxidation of the metals and this may be influenced by other causes than the general temperature. I have shown an ex-

Jan 1, 1921

By Oliver Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos industry, (2) as to the principal sources of the raw material, and (3) as to the types and modes of occurrence of asbestos. While the modern asbestos industry is comparatively new and its growth during the last decade or two has been marvelous, asbestos has been known and used in a small way for probably 2,000 years-at least since the time of the Roman Empire. Pliny refers to it as "the funeral dress of kings" and Plutarch records its use as lamp wicks. In the middle of the 18th century the deposits of the Ural mountains were opened up and the first factory for the manufacture of asbestos goods was established. But, owing to the limited demand for the goods, the industry disappeared and interest lapsed until about 50 years ago. Since 1860, the asbestos industry has made wonderful strides, and each year sees new uses to which the material can be put, and hence an increased demand and an increased output. Of the three great producers of asbestos, Canada, Russia, and the United States, Canada stands pre-eminent, producing from one-half to three-fourths of the world's supply; Russia comes second, producing ,in 1911 about two and one-half times ,is much as the United States. In 1912 the Canadian production,1 including both asbestos and asbestic, was 131,260 short tons, valued at $2,979,384; while during the same year the production of the United States2 was 4,403 tons, valued at $57,959. Canada holds the first place in the production of raw asbestos, while the United States holds the first place in its manufacture.

Jan 9, 1914

By J. F. Martin, L. M. Melnick, R. Rapp, R. C. Takacs

Recent studies on the determination of hydrogen in steel have shown that the hot-extraction method for removing hydrogen from a solid sample is preferable to its removal from a molten sample by vacuum fusion or by fusion in vacuum with tin. A number of techniques are available, however, for determining the hydrogen so extracted. They include: thermal conductivity, gas chromatography, pressure measurement before and after catalytic oxidation of the hydrogen to water and removal of the water, and pressure measurement before and after diffusion of the hydrogen through a palladium membrane. These techniques have been evaluated on the basis of initial cost, maintenance, speed and accuracy of analysis, and applicable concentration range. The results of this study showed that the palladium-membrane technique is best suited for routine use. FOR some time investigators have been concerned with the origin, form, and effect of hydrogen in steel. In such stdies', the analysis for hydrogen constitutes one of the most important phases. It is quite apparent that the results for hydrogen concentrations in a given steel are dependent on the method of obtaining the sample, storage of the sample until analysis, preparation of the sample, and analysis of the sample, including all the facets inherent in the calibration and operation of an apparatus for gas analysis. There are a number of means available for determining hydrogen. This is a critical study of some of the more common techniques in use today. In most conventional melting and casting methods, hydrogen concentrations of 4 to 6 parts per million (ppm) in steel are quite common. Because of the undesirable effects of hydrogen on steel there has been increased use of techniques such as vacuum melting,' vacuum casting, and ladle-to-ladle stream degassing, which lower the hydrogen content to levels on the order of 1 to 2 ppm. Therefore, the method used for determining hydrogen in steel must be sensitive and precise. In any analytical procedure for gases in metals there are two distinct operations—the extraction of the gas from the metal and the analysis of the extracted gas. To extract the gas from the steel, three methods have been employed: 1) fusion of the sample with graphite at high temperature; 2) fusion with a flux, such as tin, at a lower temperature; and 3) extraction of the hydrogen from the solid sample at a temperature below the melting point of the steel. Fusion with graphite is the least-acceptable method. The blank in this method is higher and more variable than in either of the other two methods. The hydrogen fraction of the total gas composition usually is between 10 and 50 pct; thus, a larger analytical error is possible. The vacuum-tin fusion4 extraction of hydrogen is probably the most rapid method in use today; the extraction time is usually about 10 min. However, with this system a bake-out of the freshly charged tin for 2 hr is necessary and a change of crucible and a charge of fresh tin are required after each day of operation whether one or thirty samples have been analyzed. In addition, frequent checks of blank rates are required since CO and Na are continually being given up by the steel samples dissolved in the tin bath. The composition of the gas in this method lends itself readily to analysis; although the hydroge concentration may fall to as low as 50 pct, more often it is above 90 pct, thus allowing a more precise analysis (because of less interference from other gases). In 1940 ewell' published the hot-extraction method for extracting hydrogen from the solid sample, comparing analysis for hydrogen extracted at 600°C with similar analysis for the gas extracted at 1700°C by fusion with graphite. Good agreement for hydrogen was obtained between these two methods, provided sufficient time was allowed for extraction at the lower temperature. carsone obtained good results in his comparison of this hot-extraction method with vacuum-tin fusion. Subsequent work by Geller and sun7 and Hill and ohnson' has shown that steel samples should be heated to at least 800°C to effect the release not only of the diffusible hydrogen but also of the "residual" hydrogen that may be present as methane. Since the rate of evolution of hydrogene9l0 depends on such factors as sample size and composition, thermal history, and extent of cold work, a fixed extraction time is not possible. Extraction times of 30 min are normal, but 2 hr are not unusual. Induction or resistance heating may be used in the hot-extraction method. With resistance heating the

Jan 1, 1964

By W. R. Hibbard, J. D. Nisbet

The high temperature properties of Fe-Cr-Co-Ni base alloys and the effects of hardening element additions on these properties are rationalized on the basis of general principles of alloying. DURING the past few years the base elements in high temperature austenitic alloys have gradually been changed from iron-rich materials to nickel-rich, then to cobalt-rich and more recently to various iron, cobalt, and nickel combinations, all with an approximately constant chromium content of 20 pct. Concurrently, the hardening additions of the incongruous* elements, have been shifted from small amounts of a single element to various ratios of molybdenum, tungsten, columbium, carbon, titanium, and aluminum with the percentages of these constituents continually increasing. It has been known that the typical soft high temperature alloy (such as Inconel) consisted of face-centered cubic austenite, but the effect of varying the composition of the base elements, iron, chromium, nickel, and cobalt, has not been broadly analyzed. Therefore, it was reasoned that the first major problem in the understanding of the properties or the further development of high temperature alloys was to study systematically the effect of composition upon the mechanical properties of face-centered cubic Fe-Ni-Co-Cr austenitic solid solutions. The matrix of the strong high temperature alloys (such as Inconel X) is usually also a face-centered cubic solid solution of iron, nickel, chromium, and cobalt but with additional phases which can be generally classified as intermetallic compounds and carbides. It is usually observed that combinations of the hardening elements, tungsten, molybdenum, columbium, tantalum, titanium, aluminum, carbon, and others have been used in these strong high temperature alloys. Thus, it was reasoned that a second major problem in studying these alloys was to understand the effect on mechanical properties of adding

Jan 1, 1954

By A. Taylor

IN a previous communication,l the quaternary system Ni-Cr-Ti-A1 was described in detail and it was shown how certain alloys used for high-temperature applications could be construed as consisting of Ni,Cr suitably modified by the addition of aluminum and titanium in relatively small amounts. With the correct aging treatment, the ordered face-centered-cubic Berthollide phase, y'-Ni,Al, could be precipitated from the face-centered-cubic primary y-solid solution. By increasing the proportion of titanium with respect to aluminum, it was also possible to precipitate the very brittle hexagonal-close-packed Daltonide phase, ?-Ni,Ti. From the nature of the system it seems reasonable to expect the y and y'-phases to take appreciable amounts of cobalt and iron into solid solution. In the case of the present investigation it was decided to confine the work to iron additions only. This element may be introduced in two quite distinct ways: 1) as a simple replacement for nickel; and 2) as a replacement for chromium, titanium, and aluminum. The second method of iron addition forms the basis of the present investigation, which is, in effect, a study of the pseudo-quaternary system Ni,Cr-NiPe-Ni,Ti-NLAl. For purposes of reference, Figs. 1, 2, and 3 have been included and illustrate the quaternary system Ni-Cr-Ti-A1 described in the previous paper along with sections through N&Cr-Ni,Ti-Ni,Al at 750" and 1000 "C respectively. As will be shown below, the pseudo-quaternary system with components Ni,Cr, NiPe, Ni,Ti, Nihl is remarkably similar in many ways to the face defined by Ni,Cr-Ni,Ti-Ni,Al because of iron re-

Jan 1, 1958

By T. J. Whalen and Michael

The grain shape of the carbide in nickel-bowled ad cobalt-bonded titanium carbides was studied by microgiaphic examination, and the influcence of sintering atmosphere, sintering substl-after, ami the amount of metal binder on the grain shape was determined. If was found that the Carbide grain cross sections in the nickel and cobalt cermets ranged from round to angular, depending on the sintering conditions. The spheroidization of the carbides in both cobalt-bonded and nickel-bonded titanium carbides may be attribicted to oxygen. In the course of studies on titanium-carbide base cermets, various investigators have reported on the shape of the carbide grains, and it was noticed that grain shapes were obtained which were either spheroids, or polygons with rounded or square edges. It was also noted that the shapes of the carbide grains changed with time or composition. skolnickl showed that the titanium-carbide grains. after infiltration in vacuum with nickel tended to spheroi- dize with time. The titanium-carbide skeleton was located on a beryllia plate during infiltration. Gur-land,' who studied the microstructure of titanium carbide-cobalt compacts, showed that the carbide grains are round after 1 hr at 1450oC in a hydrogen atmosphere and angular after 7 hr at the same temperature. Goetzel3 has found that the carbide grains in compacts with a high binder content. 40 to 60 pet. tend to be spheroidized. whereas Blumenthal and silverman4 pointed out that the higher binder contents could yield either round or rectangular grains with rounded edges. depending on the nature of the binder. It is the purpose of this paper to present experi-

Jan 1, 1961

By J. R. Spencer

When supplies of high pressure mercury or other liquids are required in analytical work, it is convenient to have the source of supply at a relatively constant pressure and available in sufficient volume to satisfy the requirements of the apparatus in use. It is also desirable that the pressuring device be as simple and as inexpensive as possible and convenient to operate. This pump combined with a small storage reservoir containing gas under pressure has the attributes of (1) positive control of the maximum output pressure through the use of a regulator in the low pressure air supply; (2) an increasing capacity as the rate of withdrawal of mercury from the pressured system is increased; and (3) simplicity, requiring only the use of a lathe, drill press, and welding unit in its construction. DESCRIPTION Essential parts of the pump are shown in Fig. 1. In appearance the unlt is similar to the usual steam pump in common use in industrial applications although considerably smaller in size. The main differences lie in the area ratio of the air and mercury pistons and in the design of the air valve mechanism. Approximate diameters of these pistons are 4.25 in. to 0.375 in. respectively, giving an area ratio of about 130 to 1. The air piston (2) is attached to the end of shaft (4), with the mercury piston being merely a reduced extension of the shaft. Mercury intake and discharge to the pump are controlled by high pressure check valves that screw into the ports indicated at (6). Air supply is controlled by the valve assembly mounted on top of the

Jan 1, 1950

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley's paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley's formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By D. W. Rudd, D. W. Vose, J. B. Vetrano

In an earlier paper the permeability character of Mo-0.5 pct Ti to hydrogen was described.' It was shown that this alloy is a more effective barrier to the passage of hydrogen than previously studied systems, i.e., copper,2 nickel,3 and several stainless steels.4 The permeability of Hastelloy B to hydrogen was investigated as a material having promising high-temperature structural properties which might have a low permeability to hydrogen. The general theory of permeation has been previously discussed,' and here only a summary of the more important results are given. It is found that except for very thin membranes, at low temperature, permeation of a gas through a metal barrier is determined by the rate of diffusion of the gas through the crystal lattice of the specimen, and that for hydrogen and the common diatomic gases, this passage involves dissociated particles as the diffusing species. The rate of permeation for hydrogen is therefore proportional to the square root of the pressure. It has also been found that the rate of permeation is inversely proportional to the thickness of the barrier. The apparatus used in this investigation was fundamentally the same as that employed in previous studies,' except that several simplifications result in the case of Hastelloy, since oxidation at the temperatures investigated is no longer a problem and welding of the specimen is relatively easy. A cross section of the membrane assembly is shown in Fig. 1. When finished, the assembly is about 5 in. long. The wall thickness is about 6 times the membrane thickness. The membrane (A) can be maintained at

Jan 1, 1963

ZAY JEFFRIES (author's reply to discussion *).-Messrs. Merica's and Humfrey's criticisms of some of my conclusions are rendered in the true scientific spirit by means of which differences of opinion are gradually smoothed out and all participants are benefited. It is true that the statement of generalizations on such a complex subject is hazardous, but I shall endeavor to point out the explanations for the discrepancies noted. Owing to the fact that I am now submitting a long paper on the same general subject to the Institute, my present remarks will be brief. Dr. Meric&s Assumptions' I agree with No. 1 and No. 2, with the modification that the A (amorphous) metal between grains of annealed metal has substantially the same properties as that at slip planes in deformed metal, but the two have different arrangements with reference to C (crystalline) metal and they may be in different conditions as regards internal stress, thickness, and nature of contact with C metal. Assumption 3.-I believe Fig. 1 is wrong. I know of no evidence to substantiate the curves. I believe cc (elongation of C phase) = 0 (approximately) at all temperatures and ?A (elongation of A phase) has finite values at elevated temperatures only; but these play no important direct role in the ordinary deformation of metals at low temperatures. I believe Ec (elastic limit of C phase) = Tc (tensile strength of C phase) because as soon as C metal begins to deform permanently it would rupture were it not for the A metal generated by its breakdown. We know that Ec = Tc in brittle crystals and a crystal cannot be permanently deformed without generation of A metal. Therefore Dr. Merica's

Jan 12, 1918

By J. S. Bowles

DISCUSSION, M. Cohen presiding J. W. Christian (The Inorganic Chemistry Laboratory, oxford, Englandl)—I was very interested in Dr. Bowles' results on the suppression of the transformation by solid films of alcohol or propane. The transformation in cobalt, which is also martensitic, can be explained by a mechanism involving the reflection of "half dislocations" down a series of atomic planes.* This reflection process is similar to that considered by Frank13 for plastic deformation on a single slip plane and, as he pointed out, reflection would be impossible if the metal were immersed in a liquid of higher density. It seems possible that solid films of alcohol have a similar effect on the lithium transformation. Reflection should also be possible at a grain boundary, though a higher kinetic energy of the dislocation, and hence a lower temperature would be required. As Dr. Bowles used coarse grained polycrystalline speci- mens, transformation on cooling should still have occurred in grains which did not form part of the outside (free surface) of the metal. This may account for the X-ray lines of the low temperature phase which were found. There is thus the interesting possibility that in a polycrystalline specimen a liquid, or in some cases a solid, film of material of or or higher density will lower M,, while in a single crystal it should suppress the transformation completely. In the case of cobalt it is necessary to find a dense liquid which will not react with the metal at the transformation temperature. The most promising liquid appears to be pure lead, but it is very difficult to devise a method of investigating whether or not this does suppress the transformation.

Jan 1, 1952

By W. J. Reagan

MANY factors enter into the manufacture of basic open-hearth steel of high quality. Perhaps the two most important are temperature and the iron oxide content of the metal. If we can control these two factors we can essentially control basic open-hearth practice. SOURCE AND EFFECT OF IRON OXIDE Earlier investigators, especially Herty and his associates, have shown that iron oxide is introduced into the open-hearth furnace in four ways:1 1. - By oxidation of the scrap by furnace gases. 2. By decomposition of the limestone. 3. By oxidation of the iron oxide in the slag by furnace gases. 4. By direct addition of iron ore to the charge. We also know that the speed of operation of an open-hearth furnace depends, for a given charge and given combustion conditions, on the rate at which iron oxide will diffuse from the slag into the metal. The rate of diffusion depends upon a number of variables, such as iron oxide content of the slag, slag viscosity, etc., which also depend upon the amount of iron oxide in the metal, amount of carbon present, temperature, and so forth. For a given carbon and a given temperature, the iron oxide content of the metal is in proportion to the iron oxide content of the slag. This fact can be easily verified by analysis of slag samples taken as described by Herty.2 It is preferable to take these samples just before deoxidation. In killing the steel samples with aluminum it is desirable to use aluminum rod of 99 per cent purity; ordinary commercial aluminum rod with a purity of approximately 92 per cent is not satisfactory. In drilling these samples it is also essential to take the largest amount of drillings possible. This gives more accurate results because it eliminates spotty segregation of Al203.

Jan 1, 1932

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. No doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data.

Jan 1, 1967

By Roger L. Brockenbrough

Steels available for mine-shaft applications are discussed, and the use of steel linings for round and rectangular shafts is reviewed. For rectangular shafts, frameworks constructed of square or rectangular steel tubes offer advantages. Also, corrugated steel sheeting provides a suitable alternative to timber lagging for spanning between the main shaft supports. For round shafts, self-supporting cylindrical steel liners, with circumferential stiffeners to prevent collapse, have been used to depths up to 6000 ft. Several large-diameter round shafts have been constructed with a concrete lining and an internal framework: of high-strength low-alloy steel tubes. It is concluded that in any new shaft construction steel designs should be investigated as economical alternatives to designs using other materials.

Jan 1, 1976