Search Documents

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By J. T. Williams

The equilibria in the V-Zr alloy system were investigated by solidus temperature determinations, thermal analysis, dilatometry, electrical resistance measurements, microscopic examination, and X-ray diffraction analysis. There is a eutectic reaction at 1230°C between a compound, V2Zr, and a solid solution containing 10 pct V in ß zirconium. V2Zr decomposes at 1300°C into liquid and a solid solution containing about 10 pct Zr in vanadium. The eutectic composition is probably about 30 pct V. A eutectoid reaction between V2 Zr and a zirconium takes place at 777°C at a very high rate. The eutectoid composition is 5 wt pct V. The limit of solubility of zirconium in vanadium was estimated to be 5 pct at 600°C. No attempt was made to determine the liquidus for the system. THE recent availability of large quantities of high purity zirconium has stimulated the study of zirconium binary systems. The equilibrium diagram for the V-Zr system has received little attention, however. Wallbauml appears to have made the first report concerning the equilibria in these alloys. He reported the existence of a compound, V2Zr, having the MgZn2 ((214) type of structure with a, = 5.277 kX and c° = 8.647 kX. Anderson, Hayes, Roberson, and Kroll2 made a survey of some potentially useful zirconium binary alloys and found that zirconium probably dissolves a small amount of vanadium. They reported the probable existence of a compound between the two elements and suggested that the zirconium-rich solid solution undergoes a eutectic reaction with this compound. Pfeil," in a critical review of the existing information, estimated that the solubility of vanadium in zirconium is less than 4.7 pct and probably less than 1.8 pct. Rostoker and Yamamoto' proposed a partial diagram for the V-Zr system in a survey paper on vanadium binary alloys. Their diagram indicates the compound, V,Zr, a eutectic reaction at 1360°C, a peritectic reaction at 1740°C, and a limit of solubility of zirconium in vanadium of about 3 pct. They obtained no information on the equilibria in the zirconium-rich alloys. In view of the potential utility of the V-Zr alloys and the incomplete knowledge concerning the equilibria in the system, an attempt was made to establish the constitutional diagram. Preparation of the Alloys Raw Materials: The vanadium for making up these alloys came from the Electro Metallurgical Corp. Zirconium came from two sources. In the beginning of the investigation, sponge zirconium from the Bureau of Mines was used in making some of the alloys. Later, iodide metal made at the Westinghouse Atomic Power Development Laboratories became available. This material was used in the preparation of all the dilatometric and resistance specimens and about two-thirds of the solidus temperature specimens. A typical manufacturer's analysis of the vanadium is shown in Table I. No other analysis of the vanadium was made. The metal contained a dispersed second phase and did not have a sharp melting point. Typical results of spectrographic analysis of the Westinghouse zirconium are shown in Table 11. These data indicate a very high purity. The Bureau of Mines sponge metal was probably less pure but had good ductility. Melting: All of the alloys used in the investigation were made by melting pieces of vanadium and zirconium together in a dc electric arc furnace similar to those of Geach and Summers-Smith, craighead, Simmons, and Eastwood," and others. Melting was done in an atmosphere of helium scavenged of residual air by the preliminary melting of a separate charge of zirconium. Each ingot was turned over and melted at least three more times before removal from the furnace to aid in the attainment of homogeneity. Alloys prepared for use in the investigation are listed with the results of solidus determinations in Table III with the exception of the following compositions upon which no solidus determinations were made: 0.29, 0.54, 4.57, and 5.55 pct V. Analysis: The weight of each ingot made from iodide zirconium was within 0.1 g of the total weight of the initial charge, about 90 g. Since each component of each charge was weighed to the nearest 20 mg for amounts less than 10 g and to the nearest 0.1 g otherwise, the gross composition of an ingot could be calculated accurately. Chemical analysis for the vanadium content of several alloys agreed

Jan 1, 1956

By R. M. Bird

FEW persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co.

Jan 1, 1926

By J. E. Steiner, J. M. Hodge, M. A. Orehoski

Ingots of four steels (1045, 1080, Ni-Mo-V, and Ni-Cr-Mo-V) were cast at pressures varying from about 1 to 760 mm of mercury, so as to obtain a range of hydrogen contents in each steel. The susceptibility of these steels to flaking was evaluated by cooling hot-rolled blooms at a range of cooling rates, varying from water quenching to slag cooling, and studying the occurrence of flaking as a function of cooling rate. The steels exhibited differences in susceptibility to flaking, and a tlzreshold value for hydrogen content for each steel was found, below which the susceptibility was very low and above which the susceptibility increased markedly with increasing hydrogen content. Mechanical property evaluations, metallogvaplzic exantinations, and X-my diffraction determinations o,t retained austenite were made on samples from the blooms. A mechanism of flaking which is consistent with the observed behaviors, the effects of hvdrogen content, and the differences in susceptibility among the steels investigated is postulated, based on the results of mechanical property evaluations and metallographic and X-ray diffraction studies. ThE important role of hydrogen as a factor in the occurrence of "flakes" or "hair-line cracks" in steel has now been established by many investigations. These have included investigations by steel producers and forging manufacturers, to whom the prevention of flaking is a very real and serious problem, and many research studies aimed primarily at establishing the mechanism of this behavior Several investigators3 have reported that steels cast at reduced pressures (absolute pressures of about 1 mm) not only are low in hydrogen content but are essentially insensitive to the formation of flakes. These investigations have shown that a general relationship exists between hydrogen content and susceptibility to flaking. The difficulty of obtaining suitable samples of steels of a given composition with the desired range of hydrogen contents, particularly in the relatively large sections in which flaking most commonly occurs, has been the principal obstacle to quantitative evaluations of these relationships. Steels with intermediate hydrogen contents between 1 ppm, and the 4ppm or higher of air-cast steels are generally not available in commercially produced steels. Laboratory procedures, in which the hydrogen is introduced into solid steel samples by heating in a hydrogen atmosphere under pressure, generally involve a limitation in the size of the sample which can be treated, and thus are not representative of the behaviors in large sections. The availability of a facility at the South Chicago Works of U.S. Steel, in which several ingots could be cast from a single heat of steel at total air pressures ranging from 0.25 to 760 mm of Hg, has made it possible to overcome this obstacle and to obtain ingots of a given steel covering the intermediate range of hydrogen contents desired. These ingots, furthermore, are of a size suitable for the production of product with section sizes large enough to be representative of the products in which flaking most commonly occurs in commercial production. In these experiments, this facility was used to study the relationships between hydrogen content and the susceptibility to flaking of four steels, two plain carbon steels at 0.45 and 0.80 pct C and two low-carbon alloy steels representing a medium and a rather high hardenability level. These flaking studies were supplemented by evaluations of mechanical properties and by metallographic studies on samples from the blooms, in order to obtain pertinent information on the factors other than hydrogen content which influence the susceptibilities of these steels to flaking. Based on the results of these tests, a mechanism for the initiation and propagation of the flaking cracks, which is consistent with the observed behaviors, is postulated. MATERIALS AND EXPERIMENTAL WORK Steelmaking and Conversion. To provide material for the investigation, five 29- by 35-in., hot-topped, big-end-up ingots were cast from each of four 80-ton, basic electric-furnace heats of four different steels (a 1045 steel, a 1080 steel, a Ni-Mo-V steel, and a Ni-Cr-Mo-V steel). A double-slag practice was used on all steels and the two plain carbon steels were Si-A1 deoxidized with an addition of 2 lb of A1 per ton, while the Ni-Mo-V and Ni-Cr-Mo-V steels were deoxidized only with silicon and

Jan 1, 1964

By N. J. Grant, A. W. Mullendore

Three aluminum alloys of 0.94, 1.92, and 5.10 pct Mg, prepared from very high purity metals, were tested at 500°, 700°, and 900°F in creep rupture. The degree of strengthening through solid-solu-tion alloying and the effects on the deformation characteristics and fracture were examined. The ductility of the alloys as a function of stress and temperature was closely followed. STUDIES of the creep process in pure metals in recent years have done much to expand the understanding of the fundamental deformation and recovery processes that contribute to overall creep behavior. In order that this knowledge may be applied to commercial alloys, it is necessary to know the principles governing the effect of alloying on the mechanisms of creep. A limited amount of work has been performed in this field, but few investigators have attempted to follow the changes in particular creep mechanisms with alloying. Recently, studies of the effects of solid-solution alloying on the plastic properties of aluminum have been conducted by Dorn, Pietrokowsky, and Tietz,1 Sherby, Anderson, and Dorn,2 and Sherby and Dorn.3 This paper presents the results of an investigation of the effect of solid-solution alloying of high purity aluminum with magnesium on the creep-rupture properties, and correlates these observations with changes in the creep mechanisms. This work is thus an extension of the creep-rupture observations of Servi and Grant4,5 and the deformation studies of Chang and Grant.6,7 Experimental Procedure Three alloys of aluminum containing approximately 1, 2, and 5 pct Mg were tested. These alloying additions are all within the solid-solubility limit at the testing temperatures.' The analysis of the materials is presented in Table I. The tests fall into two categories: l—creep-rup-ture tests at 500°, 700°, and 900°F, and 2—structure study tests performed primarily at 700°F. Speci-mens of 0.160 in. diameter with milled flats for metallographic observations" ' were utilized for the structure studies. All specimens were annealed in one step to give the desired grain size for the tests. Table II presents the annealing data and final grain sizes. The specimens were polished electrolytically before testing with Jacquet solution (2/3 acetic anhydride, 1/3 perchloric acid) at 25" to 30°C, and 15 to 20 v. Creep-rupture testing was performed under constant load with the apparatus previously described." Results and Discussion Creep-Rupture Properties: The log-log plots of creep-rupture data are presented in Figs. 1 and 2. For these very pure single-phase alloys, the minimum creep rate and the rupture life both exhibit straight-line dependence on stress in this method of plotting as they have for commercial alloys0,10 and for pure aluminum." Curve breaks, based on the use of straight-line segments, at 500°F have been found by metallographic study to correspond to a transition from low to high temperature behavior and so represent zones of equicohesion. Specimens on the high creep-rate side of the break showed normal granular deformation processes whereas those on the low creep-rate side showed rapidly increasing grain-boundary sliding and migration with extensive evidence of intercrystalline cracking at 500°F. Two micrographs of the 0.94 pct Mg alloy, Fig. 3, show the increased participation of the grain boundary in the deformation process at 500°F with decreasing stress. In Fig. 3a is shown the structure of a specimen which exhibits little deformation along the grain boundaries and failed transgranularly; in Fig. 3b is shown the increased deformation along the grain boundaries at a lower stress for a specimen which showed appreciable intercrystalline cracking. The severity of intercrystalline cracking increased with increasing magnesium content at 500°F. Intercrystalline cracking disappeared in most of the specimens at 700°F and persisted only in the 5 pct Mg alloy at high creep rates. At 900°F all of the specimens deformed with extensive grain-boundary participation, including extensive grain-boundary migration. None of the alloys at 900°F showed intercrystalline cracking.

Jan 1, 1955

By J. P. Heller

The purpose of this discussion is to comment briefly on one of the points raised in the paper. The topic is that referred to in the Conclusion 2, in which the authors note a "disproportionate increase in mixing rate" as they proceed from a displacement performed at viscosity ratio 0.998 to one at 1.002. The recovery curve of this displacement, Fig.2A, shows a quite noticeable difference between the two runs in which displaced and displacing liquids were interchanged. This difference is ascribed by the authors to the change in viscosity ratio between the two experiments. This interpretation of the experimental results must certainly be based on rather precise measurements of the fluid viscosities or, at least, of the ratio of their viscosities. The ordinary Ostwald viscometer, employed in the usual way, is only just able to distinguish between liquids whose viscosities differ by two or three parts per thousand. The experimental refinements which then must have been necessary to measure with any precision a viscosity ratio of 1.002 would be worthy of mention. Indeed, one would have expected the authors to devote at least a paragraph to the display of this technique. For the same reason - to emphasize that the details of such unusually critical experimental work should be reported and discussed in the literature — I would have liked to see some comment by the authors on the requirements for temperature control during both the viscosity measurements and the displacement experiments. The temperature coefficient of viscosity of Soltrol C at room temperature has been measured in this laboratory at about - 1.9%/1°C. How much did the coefficients for the fluid mixtures used in the experiment differ from this and from each other Even if the two fluids were identical in this respect, it would appear that a temperature difference of .l°C between them in the flow system would produce a viscosity con- trast equal to that imposed by their composition. Reference to the experimental solutions of these problems would render Conclusion 2 more credible. Published theoretical work on the stability problem contains no indication of such extreme sensitivity to the viscosity ratio in the immediate neighborhood of unity. On the contrary, perturbation calculations such as those made by Chuoke1 and Perrine2 lead to initial finger growth rates proportional to the first power of the viscosity difference. The later instability growth calculated by Scheidegger,3 using the assumption of zero pressure gradient perpendicular to the average flow, is also simply proportional to the viscosity difference. The conflict regarding the sensitivity of the dependence of instability growth or mixing rate on the viscosity contrast needs explicit recognition in the literature. In particular, it would seem that the experimental work reported here should be supported by a more detailed description of the viscosity controls. Further discussion of possible alternative interpretations of the data would also be in order. For instance, is it possible that the unconsolidstted bead pack used changed its characteristics between the runs (due, perhaps, to the handling and inverting involved in the injection of the front) Or, are the data points of Fig. 2A averages from several runs performed in a series in which the two liquids alternated as displaced and displacing fluids? To summarize, it seems to me that the relationship asserted by Conclusion 2 in the paper needs the support of more detailed experimental evidence. REFERENCES 1. Chouke, R. L., van Mews, P. and van der Poel, C.: "The Instability of Slow Immiscible Viscous Liquid-Liquid Displacements in Porous Media", Trans., AIME (1959) Vol. 216, 188.

By E. B. Burwell, R. H. Nesbitt

A NEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery.

Jan 8, 1954

By James Douglas

Discussion of the paper of James Douglas, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 29, May, 1909, pp. 439 to 451. JAMES DOUGLAS, New York, N. Y. (communication to the Secretary*) :-In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for .1906 an explanation given by him in accounting for the small production of by-product coke. It was that the markets for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908 1 does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, lie says (p. 241): "The year 1908 was not marked by any notable gain in the construction of by-product coking plants, though some new work was done. There was a net increase of 115 in the number of completed ovens in 1908 over 1907, the totals for the two years being, respectively, 3,892 and 4,007. The additional equipment consisted of 140 Koppers regenerative ovens built at Joliet, I11., by the United States Steel Corporation, but this increase was partly offset by the dismantling of Y5 Semet Solvay ovens at Sharon, Pa., the net gain being 115 ovens. Included in the total of 4,007 completed ovens in 1908 are 152 Newton-Chambers ovens at Vintondale, Pa., but as no recovery of by-products was made at this plant in 190S, the production of coke is included with that from beehive ovens. The 56 ovens of the same type at Pocahontas, Va., have not been in practical operation since they were first. installed. In addition to these there was one other by-product plant of 120 ovens. Oat. was not operated during the year. The number of retort ovens producing coke in 1908 was 3,679, as compared with 3,811 active ovens in 1907." In describing the anomaly he says (p. 249): It has been contended that the development of the by-product coking industry would have shown more rapid progress if markets for the by-products were * Received Feb. 2, 1910. Mineral Resources of the United States for 1908, Part I1., U. S. Geological Survey (1909).

Apr 1, 1910

By Chester Washburne

LEASING the Teapot dome to the Mammoth Oil Co. is the culminating anticlimax of the "conserva-tion movement." It is just the touch required to make a full fiasco of the whole affair. If the revered wielder of the "Big Stick" were still with us, we could hear it fall harder than it did on Ballinger. Of all the oil reserves set aside by presidential decree, there was only one which certainly could con-serve much oil for the future. This was Naval Reserve No. 3, on the Teapot dome, Wyoming. After secret negotiations, carefully guarded from the press and from the knowledge of other oil men, we are suddenly informed that this last and only known chance to save much oil for future naval needs has been given away for early development.

Jan 6, 1922

By J. L. Rodda

THE desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwilt1 has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goerens,2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for as given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest proce-dure. The largest particle in a given portion is. then determined by Stokes' law:3

Jan 1, 1931

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

By Philip M. Mc Kenna

When a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be considered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essential wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered. Hardness has been the property of greatest practical interest in tool materials. The word "hardness" is a generalized term lacking definite-ness unless the specific test used is described. However, efforts to explain physical properties as a consequence of chemical bond, and distance between atoms in chemical compounds have been illuminating. This seems the most generalized attack on the problem, and is based upon the idea that atoms in a lattice are held together as the square of the valence and inversely as the square of the distance between the atoms. The compounds compared must all be of the same crystalline arrangement. 100 W2 It is interesting to note the values of the figure 7 A 3 /3for a number of

Jan 1, 1938

By Philip M. Mc Kenna

When a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be considered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essential wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered. Hardness has been the property of greatest practical interest in tool materials. The word "hardness" is a generalized term lacking definite-ness unless the specific test used is described. However, efforts to explain physical properties as a consequence of chemical bond, and distance between atoms in chemical compounds have been illuminating. This seems the most generalized attack on the problem, and is based upon the idea that atoms in a lattice are held together as the square of the valence and inversely as the square of the distance between the atoms. The compounds compared must all be of the same crystalline arrangement. 100 W2 It is interesting to note the values of the figure 7 A 3 /3for a number of

Jan 1, 1938

By J. Chipman, G. G. Hatch

T. ROSENQVIST*—It is a pleasure to see the excellent way in which the experimental part of this work has been handled. There seems to be little doubt that the distribution data obtained corresponds most closely to thermodynamic equilibrium under the prevailing reducing conditions, namely equilibrium with graphite and one atmosphere CO pressure. The desulphurization curves in Fig 10 show the same general feature as the curves given by Holbrook and Joseph, but the distribution ratios are from 20 to 40 times greater—undoubtedly due to a closer approach to true equilibrium. In the theoretical discussion, the authors calculate a theoretical distribution (S) ration -jg-. which they find to be about 50 times greater than the experimental. The deviation is so great that the basis for their calculation needs a more thorough examination. The authors base their thermodynamic calculation on free energy expressions where diluted solutions of FeS and CaS are used as standard states. (The activity coefficient in diluted solutions is taken to equal unity.) Such a standard state will change when the nature of the solvent is changed. Taking the free energy of the reaction [FeS] ? (FeS), Eq 2, which is derived from the distribution of sulphur between an iron and a FeO-melt, it is very unlikely that the free energy of this reaction will be the same for a distribution between pig iron and a calcium silicate slag. Therefore a more fundamental basis for the thermodyuamic calculations seems needed, where all thermodynamic equations are referred to unambiguously defined standard states. The most natural standard states for CaO and CaS are the pure solid substances at the same temperature. As standard state for sulphur in iron, pure liquid FeS can be used. This rules out Eq 2 [FeS] ;=s (FeS) because ?F° = 0. The standard equation will then be: FeS, + CaO6 + Cgraph ?Fei + CaS8 + CO. vFo1773 = 25,000 cal It would be more universal and also simpler to refer the escaping tendency of sulphur in liquid iron to the corresponding H2S/H2 ratio which can readily be determined experimentally. As standard state a gas mixture H2S/H2 = 1/1 can be used. (This corresponds at the temperature of liquid iron closely to one atmosphere S2 vapor.) Thus the standard equation for the sulphur reaction can be formulated as follows: H2S0 + CaO3 + Cgraph ?H2o + CaS8 + COg The standard free energy of this reaction has been calculated from the best available data to AF°m3 = —35,000 cal. This gives for the equilibrium constant at 1500°C Now, the solubility of CaS in blast furnace slags has been determined by McCafferey and Oesterle* and corresponds at 1500°C to about 10 pet S (varying somewhat with the composition of the slag.) If the activity of CaS is assumed linear between 0-10 pet as curve 1, (see Fig 11), then acaO = 0.1 (S); (S) being wt. pet sulphur in the slag. For a diluted solution of sulphur in an iron melt saturated with carbon, the ratio H2S/H2 is, according to Kitchener, Bockris and Liberman,f about 0.01 [S], [S] being wt. pet sulphur in iron. Substituting these values in the expression for Kp we find The value 2.103 is only 4 times greater than the experimental coefficient found by Hatch and Chipman, but the value is very sensitive to a small error in AF°. A better agreement with the experimental distribution coefficient can be obtained if one assumes the activity of CaS to run like curve 2 (Fig 11). This (S) will give a lower theoretical W, value, a value which varies with (S) exactly as Hatch and Chipman learned. Such a shape of the activity curve, which corresponds to a positive deviation from Raoult's law, is actually to be expected from the fact that liquid silicate and sulphide phases usually show incomplete miscibility. A closer agreement between experimental and theoretical data can not be expected before we have more complete data for the individual activities of CaS and CaO in the slag. The activities acaS and Ocao referred to the solid phases as standard states, are exact defined quantities contrary to the somewhat undefined expression "free lime," and they are independent of any theory for the constitution of liquid slag. J. CHIPMAN (authors' reply)—The authors wish to thank Mr. Rosenqvist for his very interesting and useful thermodynamic addition. Curve 2 of his figure offers the needed basis for explaining the increase in the ratio (S)/[S] with increasing sulphur content. Attention is called to an error in the printed paper: Fig 2 and 3 are reversed. M. TENENBAUM*—In the figures showing the relationship between excess base and sulphur distribution (Fig 6, 7 and 9) the slope of the curve tapers off in the negative basicity range. Somewhat the same thing is observed with open hearth slags. In that case, the fact that some sulphur distribution between slag and metal is obtained with negative basicity is interpreted as indicating some dissociation of the lime silicate compounds whose existence in oxidizing basic slags has been used to explain various observed phenomena with regard to other slag-metal reactions. In the case of the blast furnace slags, the reduced slope of the sulphur distribution curve with decreasing excess base is attributed to the amphoteric effect of alumina. Has the possibility of other explanations been investigated ?

Jan 1, 1950

By J. L. Rodda

The desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwiltl has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goereq2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for a given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest procedure. The largest particle in a given portion is then determined by Stokes' law:3

Jan 1, 1932

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By Kenneth L. Adams

10.3-1. Introduction. Equipment replacement or maintenance is of major concern to every company today. It can be the difference between an efficient and profitable operation or an inefficient and struggling one. Mining equipment, as everyone knows, will not last forever. Some equipment becomes obsolete before it wears out while some may be doing its intended job, yet not economically. It is a major problem for management to make the decision as to whether a piece of equipment should be repaired or replaced. There are numerous approaches to this problem; using formulas, charts, and graphs. These would be very good if all conditions were stable. Since conditions and requirements are constantly changing, an accurate observation cannot be derived from a set formula. A formula does, however, serve as a reminder to include most of the items that should be considered when evaluating old and new equipment. In the field of mining there are several questions which enter into the reasoning that are difficult to put into an equation. Some of these are: 1. Will the present equipment produce the required output of the mine, or an increase if necessary? 2. Are reserves adequate to support the purchase of new equipment? 3. Can the old equipment be repaired to efficiently continue the mining operation? 4. What is the stability of future markets for the product? Depreciation rate, or the write-off life, is a factor that can directly effect decisions on replacement. If the initial life expectancy is too long and the price of equipment is not written off when discarded, then the original investment has not been recovered. If the write-off time is too short, then the equipment is written off before replacement is even considered. In this case, the depreciation accrual is usually used to finance some other phase of the operation. In view of the increasing prices, the amount of depreciation fund is generally too small for much incentive to replace an older unit

Jan 1, 1968

By W. P. Frey

THE briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.1 It has passed. the stage of experiment and now rests,, on a foundation practically and financially sound. The purpose of this paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93 11,160 B.t.u. 17,500 X 0.07 1,125 B.t.u. Total 12,355 B.t.u. per pound of briquets

Jan 1, 1918

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960