Search Documents

By W. E. Wrather

DURING the war the mineral industry, and metal mining in particular, extended itself more than any other to attain the limit of its productive capacity. Likewise, probably no other industry went quite so far toward jeop¬ardizing its own economic future through depletion of material reserves. Once we looked to Europe for most of the manufactured goods we needed. Our own limited mineral requirements were easily supplied from mines near the Eastern seaboard. With expansion and industrialization, our mineral needs increased in proportion, and the centers of mining activity moved westward to Michigan, Wisconsin, Minnesota, and the Tri-State district, where seemingly inexhaustible high-grade deposits of iron, copper, lead, and zinc ores were opened and rapidly developed.

Jan 1, 1946

By P. D. Merica, H. Scott, R. G. Waltenberg

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903—1911 by A. Wilm1,2 and have been described by him and by others. 3, 4,5.6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from tempera-

Jan 1, 1921

"Located on Missouri River 16 miles N. E. from Helena, 67 miles from Butte and 18 miles below Canyon Ferry. River drainage area 16,000 sq. miles.DAM: Built in 1907; rebuilt of concrete in 1911. Maximum height 129.3 ft., length over all 720 ft.; elevation of crest 3621; elevation of bridge 3640; normal head 60'; normal tail water elevation 3568.5.SPILLWAY: Length over all 491 ft.; clear opening in 24 sections; 445' flashboards, 14 high to elevation 3635, which is 3.5' above Canyon Ferry normal tail . water elevation.PENSTOCKS: 5 of steel, 12 ft. diam., about 75 ft. long from canal to main turbines, and 3 40-inch diam. from canal to exciters.WHEELS: 5 main pairs, horizontal, center discharge, 48-inch bronze turbines, 225 rev., 4,000 h-p. at 60 ft. head, made by S. Morgan Smith Co., direct coupled to generators, and--3 single, horizontal, 25-inch units, direct coupled to exciters.GENERATORS: 5 W. E. & M. Co. water wheel type, revolving field, 2,800 k-w., 2,400 v., 225 r. p. m., 3 phase, 60 cycle alternators.OPERATION: The plant has a larger water storage than Canyon Ferry and can also use stored water from Canyon Ferry storage. Separate transmission lines 13 miles long connect to lines from Canyon Ferry to Butte, and the Plant operates in parallel with the Canyon Ferry plant."

Jan 1, 1913

THE illustration below shows the design of the face of the clock to be erected as a memorial to the American engineers who gave their lives overseas in the World War. It will be placed in the tower of the library at Louvain, which has been rebuilt through contributions from America. Large clocks seldom have figures on their faces, and each hour on this one will be marked by a gold star, the four faces containing 48 stars, one for each State of the Union. Contributions toward the memorial have been received from every one of the States, and from Alaska and Hawaii as well, but additional subscriptions are invited by the Com-mittee which is arranging for the memorial.

Jan 3, 1928

By J. M. Campbell, T. S. Buxton

The most widely used methods of predicting the volumetric properties of gas are based on the principle of corresponding states, which asserts that the compressibility factor is a universal function of reduced temperature and pressure. Previous studies have shown that the acentric factor, as proposed by Pitzer, l is an important addition to reduced pressure and reduced temperature as factors affecting the compressibility factor. Results of this study indicate that, if the pseudocritical temperature and pressure used to determine the reduced conditions are adequately predicted, characterization of natural gas-carbon dioxide mixtures with the acentric factor will allow reliable determination of the compressibility factor. Comparisons of predicted and experimental compressibility factors have shown that the pseudo-critical constant rules of Stewart, Burkhardt and Voo 2 are satisfactory for hydrocarbon mixtures. However, these rules fail to predict the pseduo-critical constants for hydrocarbon-carbon dioxide mixtures. Based on graphically determined pseudocritical temperatures for binary hydrocarbon-carbon dioxide mixtures, a correlation which gives the required correction to the Stewart, Burkhardt and Voo rules was prepared and a compressibility factor prediction technique was proposed. To test the proposed technique, compressibility factors for live mixtures of methane, carbon dioxide and either ethne or propane were experimentally determined at 100, 130 and 160F and pressures up to 7,026 psia. The predicted and experimental compressibility factors for these live mixtures had an average absolute deviation of 0.55 percent. INTRODUCTION Two-parameter generalized correlations based on the principle of corresponding states (PCS) are presently available for reliably predicting the compressibility factor of lean natural gas, i.e., natural gas with low concentrations of hydrocarbons heavier than methane. When these same correlations are used for mixtures of natural gas and carbon dioxide, large deviations between actual and predicted compressibility factors are observed. This study was undertaken to provide a means for accurately predicting the compressibility factor for such mixtures. In the past, two avenues of approach have been employed to extend the applicability of the PCS. The first has been to introduce additional parameters. The second has been to develop combination rules for predicting pseudocritical constants which do not suffer from the limitations of the commonly used molal average constants. In this study, both of these approaches have been considered and employed to arrive at a method for predicting the compressibility factor of mixtures of hydrocarbons and carbon dioxide. SELECTION OF A THIRD PARAMETER Failure of the original PCS to predict the compressibility factor for all pure gases, regardless of their mass, shape or polar moment, has led to the introduction of additional parameters into the PCS. Parameters have been introduced to correct for quantum deviations,3-5 non-spherical or globular shapes6-9 and for polar moments.8-12 In addition to these parameters which are based on some microscopic property and intended to correct for some specific cause of deviation, more general parameters based on some bulk property have also been introduced.1913-16 To use additional parameters to correct for each of the possible causes of deviation among the individual constituents of a gas mixture would require a rather complex form of the PCS. To maintain the PCS in as simple a form as possible, it is more desirable to have a single third parameter which is based on some bulk property influenced by several of the factors causing deviations. The third parameter selected for use in this study is a factor originally proposed by Pitzer.9

By E. B. Mayo

David LeCount Evans (Consulting Petroleum and Mining Geologist, Wichita, Kans.)-—Not only E. B. Mayo but also W. C. Lacy, who apparently urged the preparation of this analysis, is to be commended. Regional thinking of this type is needed to assure future success in the never-ending search for new mineralized and petroliferous districts. As is usually the case, here is a regional study that will be read by the mining geologist alone. It is ironic that several of the trends established in this study have suggested themselves in northern mid-continent, detailed, and regional studies. These, where established, have offered new keys to petroleum exploration and have provided a possible basis for unraveling a number of broad generalities. The oil geologists, active in Colorado, Kansas, and Oklahoma, would find much food for thought in Mr. Mayo's projections. To be more specific: 1) The parallelism between E. B. Mayo's Texas Lineament and the Amarillo Uplift, the Wichita Complex and the Arbuckle Complex of the Texas Panhandle and Southern Oklahoma is viewed with interest and appears especially significant when compared with the similar northwest trend of the Central Kansas Uplift, a major trend of production. 2) Considering the various northeast zones of Fig. 2, and with particular reference to Mayo's C-C, the Jemez Zone is on direct line with one of several northeast-southwest controls which the present writer has been using with some success in Kansas subsurface correlations. Considering zones of shearing, with no apparent vertical displacement, but suggesting strike-slip movement, because of the staggered effect on other features which cross such trends, Mayo's philosophy presents regional possibilities for lines of weakness, considered to this time of only local significance. 3) And, finally, in an area as distant from the Southwest as central Kansas, the north-south trends of the Fiarport-Ruggles anticline, the Voshel-Hol-low Nikkel-Burrton structures, the Dayton to Stut-gart trend, the north, slightly east trend of the Ne-maha structural complex, and others all seem to approach the north-south alignments, a through f, of Mayo's Fig. 3. Mayo's employment of structural intersections to pinpoint crustal weakness, to localize igneous activity and its accompanying mineralization is not, perhaps, a new concept, but it is a 1958 model, produced by tools improved from the ever-increasing accumulation of geological observations. The use of intersecting trends in petroleum geology is not a new idea, since much production in earlier days was encountered via the straight line projections of established trends to centers of intersection. A tragedy in this age of specialization is that iron curtains have been raised between groups, all seeking raw materials, all acolytes at the altar of structural geology, but all smugly content in and protected by the ivory towers of petroleum geology, engineering geology, mining geology, and geophysics. Mayo presents basic ideas which can stimulate mid-continent structural thinking and, in the case of cen- tral Kansas. he provides a key to replace the broad and overworked simple monoclinal, sinkhole-dotted, Karst topography credo, which is not finding its share of new oil in a state where the declining discovery ratio is disconcerting. The American Association of Petroleum Geologists would do well to add E. B. Mayo to its list of Distinguished Lecturers. Evans B. Mayo (author's reply)—In reply to David LeCount Evans' comments, it is pleasing to learn that some of the elements discussed in my paper may interest petroleum geologists as well as mining geologists. This should not be surprising, however, because the lineaments make up the framework of the continent, and the oil-bearing sediments must reflect to varying degrees adjustments of basement blocks along their boundaries. A further possibility that petroleum geologists must have considered is that the slow escape of heat from buried lineaments and their intersections has aided the separation of oil from the sediments and started the migration into traps. Regarding the specific points listed by Evans, the following are suggested: 1) The branch of Texas Lineament marked 1' (Fig. 3) is thought to extend eastward through the Capitan Mts., New Mexico, through the long Tertiary dikes east of Roswell, and beyond via the Matador and Electra ranges of the Red River Uplift, Texas. Its further continuation might be the eastern flank of the Ouachita Fold Belt. The Amarillo-Wichita-Arbuckle zone of uplifts appears to continue east-southeastward the Spanish Peaks belt (3-5, Fig. 3). The northwest-trending Central Kansas Uplift would not belong to the above set, except insofar as the Central Kansas Uplift is traversed by west-northwest folds, possible continuations of the Uinta belt (5-5, Fig. 3). 2) The possible continuations into Kansas of the Jemez zone are new to me and are most welcome suggestions. 3) Most of the nearly north-south Kansan structures mentioned by Evans are unfamiliar to me, but the Nemaha Uplift itself appears to be part of a very pronounced structure traceable from the Cerralvo Fault Zone, south of the Rio Grande, through the Bend Arch, Texas, and the Nemaha Uplift, into the Pre-Cambrian of Minnesota (?). This nearly meridional zone is crossed and broken by the Rio Grande Embayment and by the Red River-Wichita Syntaxis. Petroleum geologists realize the economic importance of these features. Perhaps it is inevitable that some papers of general interest be buried in the journals of specialized groups. Moreover, papers dealing with regional, or lineament, tectonics and its applications to exploration for economic mineral deposits are as yet few in the American literature. The opportunity to advance this field is open to all those who are not ultra-conservative and who have a lively curiosity, plenty of patience, and not too many business restrictions. In conclusion, much appreciation is extended to D. L. Evans for his comments.

Jan 1, 1960

By Valentine Garfias

THE various phases of the Mexican oil industry have received so much publicity that there is little to add to the discussion of present and future production, extent and importance of prospective fields, and status of petroleum legislation, to mention but a few of the angles of the Mexican oil problem. However, out of this wealth of information, which is generally of contradictory nature, the average petroleum man is at a loss to know something definite regarding the various questions involved so, keeping the foregoing in mind, it has been the writer's aim to record in a concise form the most reliable and up-to-date information regarding the salient features of the Mexican oil situation. PRESENT STATUS OF MEXICAN OIL INDUSTRY Production During 1921 The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of -these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 3 1/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields from about 755 per cent. of the Mexican petroleum industry.

Jan 4, 1922

R.. B. T. KILIANI, New York, N. Y.-I do not care to discuss Mr. Taggart's paper in the light of theory, as that has been very well done by Prof. Bell,1 but I should like to criticize some of his conclusions, in the light of actual operating practice at plants all over the country. 1. Mr. Taggart's first conclusion is that in crushing average ore, the character of the gangue has little effect on the efficiency of the mill. This, I believe, is not in accordance with the usual practice, since in crushing a hard ore the capacity will be much reduced below what it would be with a softer ore, while the power consumed will be practically independent of the character of the ore, being proportional only, to the load of ore and balls in the mill. 2. Mr. Taggart's second criticism is that the Hardinge mill is not suitable for grinding soft, tough material. In answer to this I might mention that the mill is being used for grinding tough, dnctile material, such as metallic aluminum, and also for grinding licorice root. 3. He says that the ball-mill works more efficiently on material of intermediate size, say 1/2 to 3/4 in., than on either coarser or finer feed.. This is true as to coarser feed. For the most efficient work, I believe that a ball-mill should be fed with material not coarser than 1 1/2 in.; it' will handle material up to 3 and even 4 in., but the reduction from 3 or 4 in. to 1 1/2 in. can be done much more cheaply and efficiently by rolls or disk crushers than in the ball-mill. 4. As to Mr. Taggart's fourth conclusion, that a greater ratio of reduction can be expected with feed of an intermediate size than with a coarse feed, I have not enough information to express an opinion. 5. His next conclusion is that steel balls are much more efficient crushing media than pebbles. Steel balls are undoubtedly more efficient for crushing coarse feed. On fine material they are also more efficient as to tons per horsepower crushed to 10-mesh, but on fine material I think it will be found that flint pebbles are cheaper than cast-iron balls, per ton of ore, although there will be a saving in power per ton by using cast iron instead of flint. The increased cost of crushing with cast iron will be due to the higher cost of iron at the present time. 6. Mr. Taggart's sixth conclusion coincides with present practice, that steel balls will grind as fine or finer than pebbles when working on the same feed.

Jan 1, 1918

By Frederic Brunton

I. INTRODUCTION THE smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at' very high efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of $1.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 tons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by Alfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Works, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913).

Jan 7, 1915

By B. Ramaswami, U. F. Kocks, B. Chalmers

The latent hardening of silver and an Ag-Au alloy was investigated by lateral compression, overshoot in tension and cormpression, and the stability of multiple-slib orientations. The latent hardening of a secondary slip systenz depends on its relation to the primary slip system. For most secondary slip systems the latent hardening is larger for Ag-10 at. pct Au than for pure silver. The maximum increase in. flow stress on a secondary slip system over that of the primary slip system was 40 pct. The work hardening during the lateral-compression test on the latent system after prestress on the primary system is iuterbreted in terms of the preferential distribution of barriers to dislocation movement with respect to the active slip system in work-lzardened fcc crystals. The work-hardening in fcc crystals is mainly due to the dislocation interactions and the barriers to dislocation movement formed as a result of reactions between dislocations of different slip systems. The operation of sources on the latent system depends on the flow stress of those systems; hence, the increase in flow stress of a latent system due to glide on an active system, which is called latent hardening, is an important element in understanding the phenomenon of work hardening. The problem of latent hardening has attracted the attention of many investigators in the past. For example, a theoretical study of the elastic latent hardening of the latent systems due to glide on an operative system has been made by Haasen' and ~troh. These calculations, however, neglect the stress required for the intersection of forest dislocations by the glide dislocations, a factor which would be important for producing macroscopic strains on the secondary slip systems. The importance of this factor will become evident from the results presented here. Attempts have also been made to determine the latent hardening of different slip systems by experimental means by the methods summarized in Table I.3-9 The experimental methods used have been subject to certain limitations. For instance, in the method used by Hauser,9 frictional constraints between the specimen and the compression platen were not eliminated by proper lubrication (see Hos- ford10). Secondly, with the exception of Kocks,6 Hauser,9 and Rohm and Kochendorfer,11 latent-hardening studies have been made on only one of the slip systems, i.e., on either the conjugate or the coplanar slip system; hence, extensive results are not available on the latent hardening of different slip systems in the same materials, with the exception of aluminum.6 It was therefore decided to study the latent hardening of the conjugate, critical and half-related slip systems in silver. Similar experiments were done in Ag-10 at. pct Au to study the effect of solute (gold) on the latent hardening of silver. Lastly, indirect evidence can be obtained by a study of the orientation stability of crystals of multiple-slip orientations in tension and compression. This method has been used by Kocks6 to supplement his studies of latent hardening in aluminum. Similar studies were made at room temperature in single crystals of silver. EXPERIMENTAL PROCEDURE The single crystals of the desired orientations were grown and the tensile test specimens were prepared as described in Ref. 12. The compression tests were made on 1/4-in.-cube specimens. The specimens were cut from single crystals, in the Servomet spark-erosion machine.13 The two cut surfaces were planed using the lowest available planing rate in the machine to minimize the deformation layer. A brass strip was used as the planing tool. This method of preparation ensured plane parallel faces for the compression tests. The deformed material was removed by prolonged etching in a weak etching solution. A weak etching solution was used to prevent pitting of the surfaces and to ensure uniform etching. About 25 to 50 µ of material were removed from all faces by the etching treatment. The specimens were then annealed for 24 hr at 940°C in oxygen-free helium and cooled in the furnace to room temperature over a period of 7 hr. After annealing, the orientation of the specimens was determined by Laue back-reflection technique to make sure that no recrystallization had occurred on annealing. The compression-test technique and setup are described in Ref. 14. The Laue back-reflection technique was used to study the overshoot in tension, the overshoot in compression, and the stability of the axial orientation in tension and compression. The tests were interrupted after every few percent strain to determine the axial orientation. In investigating the overshoot in compression, the operative system was determined by studying the asterism of the Laue spots.

Jan 1, 1965

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

(The following -list, contains the navies of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A com-plete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ADDICKS, LAWRENCE, Naval Consulting Board. ALINE, P. A., Camp Lewis. BARCUS, WALTER .J. E., Captain, Ordnance Department. BAUSH, JOHN R., Private, 1st Army Headquarters Regiment, Co. M. BENNETT, A. F., Lieutenant. BILLINGSLEY, PAUL, Engineer Officer, Aviation Section, Signal Officers' Reserve Corps. BOOTH, L. E., Ordnance Department. BROWN, JAMES F., 2d, 1st Lieutenant, Ordnance Reserve Corps, A. E. F.

Jan 4, 1918

By S. J. Sindeband

Prior to discussing the metallurgy of sintered chromium borides, it is pertinent to outline some of the reasoning behind this investigation and the purposes underlying the work. This study was initiated as an aproach to the ubiquitous problem of a material for service at high temperatures under oxidizing atmospheres, and it was undertaken with a view to raising the 1500°F (816°C) ceiling to 2000°F (1093°C) or better. For the reason that no small, but rather a major, lifting of the high temperature working limit was being attempted, it was felt appropriate that a completely new approach be taken to this problem. A summary of the thinking behind this approach was published recently by Schwarzkopf.' In briefest terms, it was postulated that the following requirements could be set up for a material which would have high strength at high temperatures. 1. The individual crystals of the material must exhibit high strength interatomic bonds. This automatically leads to consideration of highly refractory materials, since their high energy requirements for melting are related to the strength of their atom-to-atom bonds. 2. On the polycrystalline basis, high boundary strength, superimposed on the above consideration, would also be a necessity. Since this implies control of boundary conditions, the powder metallurgy approach would hold considerable promise. Such materials actually had been fabricated for a number of years, and the cemented carbide is the best example of these. Here a highly refractory crystal was carefully bonded and resulted in a material of extremely high strength. That this strength was maintained at high temperature is exhibited by the ability of the cemented carbide tool to hold an edge for extended periods of heavy service. Nowick and Machlin2,3 have analytically approached the problem of creep and stress-rupture properties at high temperature and developed procedures whereby these properties can be approximately predicted from the room temperature physical constants of a material. The most important single constant in the provision of high temperature strength and creep resistance is shown to be the Modulus of Rigidity. On this basis, they proposed that a fertile field for investigation would be that of materials similar to cemented carbides, which have Moduli of Rigidity that are among the highest recorded. The cemented carbide, however, does not have good corrosion resistance in oxidizing atmospheres and without protection could not be used in gas turbines and similar pieces of equipment. It would be necessary then to attempt the fabrication of an allied material based upon a hard crystal which had good corrosion resistance as well. It was upon these premises that the subject study was undertaken and at an early stage it was sponsored by the U.S. Navy, Office of Naval Research. Since then, it has been carried on under contract with this agency. Chromium boride provided a logical starting point for such research, since it was relatively hard, exhibited good corrosion resistance, and, in addition, was commercially available, since it had found application in hard-surfacing alloys with iron and nickel. That chromium boride did not provide a material that met the ultimate aim of the study results from factors which are subsequently discussed. This, however, does not detract from the basis on which the study was conceived, nor from the value of reporting the results which follow. Chromium Boride While work on chromium boride proper dates back to Moissan,4 there has been a dearth of literature on borides since 1906. Subsequent to Moissan, principal investigators of chromium boride were Tucker and Moody,5 Wede-kind and Fetzer,6 du Jassoneix,7,8,9 and Andrieux." These investigators were generally limited to studies of methods of producing chromium boride and detennining its properties. Some study, however, was devoted to the chromium-boron system by du Jassoneix,7 who did this chemically and metal-lographically. This system is not amenable to normal methods of analysis by virtue of the refractory nature of the alloys involved, and the difficulties of measurement and control of temperature conditions in their range. Dilatometric apparatus is nonexistent for operation at these temperatures. Du Jassoneix made use of apparent chemical differences between two phases observed under the microscope and reported the existence of two definite compounds, namely: Cr3B2 and CrB. These two compounds, he reported, had quite similar chemical characteristics, but were sufficiently different to enable him to separate them. The easiest method for producing chromium boride is apparently the thermite process, first applied by Wede-

Jan 1, 1950

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytical expressions derived previously are used to describe quantitatively effects on macrosegregation of some solidification and mold design variables. Al-4.5 pct Cu alloy is used as example. It is shown that abrupt changes in heat transfer rate result in solute-rich or solute-poor "bands". Severe solute-rich bands accowzpany "reheating" that can result, for example, from abrupt formation of an air gap at a mold-metal interface. With planar isotherms, solute-poor regions also result from reduction in cross section through which fluid flow to feed shrinkage takes place. It is suggested that the negative "cone" of segregation often found at the base of large ingots results from this reduction in cross section for feeding. Consideration is given to the positive and negative segregation to be expected in laboratory ingots in association with changes in ingot cross section. Under-riser positive segregation is considered and it is concluded this segregation results when vertical temperature gradient is low in the region of the riser; the segregation is accentuated by the temperature gradient reversal which can occur in inadequately insulated risers ("'hot tops"). Finally it is shown for Al-4.5 pct Cu alloy that the assumption of constant k and p in analytic solutions gives calculated results close to those obtained for the case of ziariable k and 0. A basic "local solute redistribution equation" was derived earlier' for calculation of macrosegregation resulting from flow of solute-rich liquid to feed solidification shrinkage, thermal contraction, and/or other contractions occurring during solidification. This expression relates fraction liquid, g~, to liquid composition, CL, at a given position x, y, z, in a solidifying Eq. [I] is for the general case of three-dimensional heat and fluid flow assuming constant solid (but not necessarily liquid) density during solidification, negligible net solute change from diffusion, and no pore formation. In this paper we first demonstrate application of this equation for calculation of macrosegregation in several examples involving one-dimensional heat and fluid flow. Specifically considered are examples in which segregation results from sudden changes in heat flow conditions. Next, Eq. [I] is used to describe segregation in examples where isotherms remain planar but where fluid flow is no longer one-dimensional. Application of this expression illustrates the type of segregation to be expected in unidirectionally solidified ingots of gradually or abruptly varying cross section. For segregation calculations, A1-4.5 pct Cu alloy is employed with constant k and p Vz = 0.172, 4 = 0.055), eutectic composition (CE = 33 pct Cu). In all examples, fraction eutectic is neglected in velocity calculations; this was previously shown to introduce little error.' A linear distribution of fraction liquid in the liquid-solid zone is assumed. In a concluding section it is shown that the assumption employed of constant k and /3 gives results close to those obtained when the actual (variable) values of k and 0 are employed.

Jan 1, 1969

By AIME AIME

M ODERN metallurgy properly belongs to this century. The great advance made in this science is directly attributable to the discovery of the Roentgen rays. Application of the results of this discovery, together with the more recent corroborating studies in electronic diffraction have definitely and for all time established this science. Metallurgists today speak with familiarity of the atoms of the different metals in terms of their orientation, atomic volumes, lattice structures, dimensional lattice constants distance of nearest approach, and the like. One matter of profound interest, which is quite staggering to the imagination of the human mind, is the enormity of the number of atoms even in a small particle of metal. As an illustration, let us compute the number of atoms in the volume of one cubic centimeter in a single grain of absolutely pure copper. Eighteen and a fraction cubic centimeters equal the volume of one cubic inch.

Jan 1, 1940

By F. B. Plummer

PROGRESS during 1940 in oil-production technology has been confined largely to a steady advancement in practices inaugurated in previous years, rather than the introduction of any new startling process or technique. The usual changes, improvements and additions in production equipment have been introduced. An increased attention to, and interest in, research has been noteworthy, resulting in improved efficiency in operation of oil wells. control, utilization of reservoir energies and reduction of production costs.

Jan 1, 1941

By E. Lifshin, R. E. Hanneman

QUANTITATIVE applications of the electron micro-beam probe frequently involve the evaluation of complex mathematical expressions and/or the analysis of large amounts of experimental data. The purpose of this communication is to describe briefly a versatile and useful computer program system that is applicable to analyze rapidly a wide variety of practical microprobe problems. This system consists of a group of ten FORTRAN programs that can be stored on tape, cards, or in the memory disc of the computer. These programs, or links, can be run individually or in any prespecified sequence without interrupting the operation of the computer or without destroying information which is being transfered from one link to another. For the program system described here a GE-235 computer with disc storage was used, so that the DCHAIN method of program linking was employed. Included in the library are programs to: 1) initiate analysis of a new set of data and transfer control between all other programs in any predetermined manner; 2) generate theoretical calibration curves of composition vs relative intensity; 3) generate empirical deviation parameters from least-square fits of experimental calibration data from standards of known composition; 4) convert raw X-ray data to corrected composition; 5) determine inter diffusion coefficients by Matano analysis of con centrat ion -distance data on a uniaxial diffusion couple; 6) determine activation energies and frequency factors of temperature-activated processes such as diffusion; and 7) generate calibration curves for determination of the thickness of thin films using microanalysis. A detailed description of these computer programs and their underlying principles is available on request from the authors."' The first program to generate theoretical calibration curves of corrected relative intensities vs composition uses the Poole and Thomas atomic number correction' and the Philibert absorption factor' with a voltage-dependent mass absorption coefficient for electrons in the alloy. A modified Castaing fluores- cence correction is also used which includes the effects of both Ka and KO radiation and over voltage.' Once the theoretical curves have been calculated in 1 wt pct intervals, these results are least-squares fit to obtain Ziebold deviation parameters' which are stored in COMMON in the computer memory. The net discrepancies between the original theoretical calibration curve and the regenerated curve using the Ziebold parameter are computed. Although this link is explicitly written for K-K fluorescent interactions, it can be applied to K-L, L-K, and L-L interactions as previously disc~ssed."~ Similar programs have also been written to utilize the Wittry fluorescence correction, Birks combined corrections, and various other corrections.' These modified programs have proved to be quite useful for quantitative comparisons of the results of the various theories. The program for conversion of raw X-ray data to corrected composition includes corrections for drift, backround, and instrumental dead time. The corrected intensities are converted to composition by use of the Ziebold equation"2 and parameter obtained from the program system. The results can be obtained for either atom or weight fractions. In addition to accurately computing interdiffusion coefficients the Matano analysis program calculates least-square smoothed values of concentration, concentration gradient, and curvature for each point on the raw input concentration profile. In order to obtain high accuracies a unique method of performing a least-square polynomial fit to incrementally advancing profile segments which overlap is used.' This program has been successfully modified for use in ternary diffusion problems3 and can readily be modified to handle analysis of diffusion profiles which include phase boundary discontinuities. This link is generally applicable to analysis of interdiffusion data obtained by other techniques as well as by the microprobe. The primary function of the next program is to least-squares fit experimental diffusion data to the normal Arrhenius function: D = Doexp(-Q/RT), to obtain values of Do and Q. In addition the probable error and one, two, and three u statistical confidence limits of DO, Q, and log D are evaluated. This program is also directly useful for analysis of any other simple temperature-activated processes including conductivity, and certain deformation and chemical processes. The program to generate calibration curves for film-thickness determination using the microprobe is based on a numerical integration of the equation derived by Cockett and ~avis.' Values of film thickness obtained by this program for copper on various substrates are in good agreement with measurements made by other techniques. Versions of the above program system have been prepared for use with or without a remote teletype connection to the computer for processing on either a real-time or time-share basis. The instrumentation coupling a microprobe to a teletype for automatic data collection and analysis by the presently described program system has been reported elsewhere by the authors.' If teletype equipment is not used to communicate with the computer, standard methods of card reading and tape reading can be used. In either

Jan 1, 1967

By James Malcolmson

(New York Meeting, February, 1913.) THE Tigre Mining Co. of Mexico, owned by the Lucky Tiger Combination Gold Mining Co. of Kansas City, decided early in 1910 to enlarge its mill, which consisted of a concentrator milling 3,000 tons of ore per month. The enlarged plant was designed to crush and concentrate 6,000 of ore and to cyanide 7,500 tons per mouth. The extra tonnage cyanided was to be obtained from tailings which were stored below the old mill. Power was supplied to the old mill from four boilers; a 150-h-p.. Corliss engine and two Weber 60-h-p. gas-engines using producer-gas made from charcoal. The total horse-power required, including 60 h-p. used for machine-drills in the mine, was approximately 275. Cord-wood cost $4.32 per cord, 8 by 4 by 3 ft., and charcoal $15 per ton. The fuel supply in the surrounding country was approaching exhaustion; more than 150 mules and 50 men were engaged in cutting and transporting this fuel, and the unsettled political, conditions in Sonora were such that it would be practically impossible to keep an organization of this kind together. The price of fuel was steadily rising and at times it became almost impossible to get sufficient fuel to operate.

Jan 4, 1913

By H. R. Peiffer

The increase in electrical resistivity, ?pT,at 78°K was measured as a function of elongation, E, at 78°K for a 2 pct (approximately) by weight finely divided alumina in silver material. The amount of increase in electrical resistivity (?pT) is a function of the amount of alumina present and can be represented by: ?pT = cen where c and n are constants. The constant c increases and the exponent n decreases with increasing alumina content. Approximately 33 pct of the resistivity increase is recovered upon annealing at room temperature. RECENTLY, dispersed phase alloys' have shown promise for use at elevated temperatures. These materials have a high creep resistance, a high-temperature strength considerably above that of the pure matrix, and a high electrical conductivity. These materials also show other properties such as retardation of re crystallization and resistance to flow even above the melting point of the matrix.' It is believed that high-temperature creep is retarded in these materials because the dispersed phase blocks the motion of dislocations. According to schoeck3 and also Weertman,4 the rate controlling process is the climb of dislocations around the dispersed phase particles. Any mechanical property of these materials, or any other material for that matter, can be explained on the basis of defect structures and their interrelations. It would certainly be interesting to learn something about the effect of a dispersed phase on dislocation densities and also their effect on point defect concentrations following cold work. This is the purpose of the research discussed herein. The method used was the measurement of the electrical resistivity as a function of elongation at low temperatures. This scheme has already been applied to the studies of pure metals.5 Electrical resistivity measurements conducted on pure metals such as copper, silver, gold, and so forth, have indicated that defects such as vacancies and dislocations are formed during deformation.5 It has been shown by van Bueren6 that the resistivity change, ?p, should increase with elongation, E, according to the following relation: Ap=Al/2 + B£3/2 where A and B are constants of the system; ?p is in µ? cm. The first term refers to the amount of resistivity change associated with line defects and the second term with the change associated with point defects. A later calculation yielded exponents of 3/4 and 5/4, respectively.6 Manintveld7 has shown that the resistivity of copper increases with strain according to a 3/2 power law, whereas van Bueren has shown that the resistivity of silver increases according to a 5/4 power law. Assuming then that van Bueren's calculations are correct, it appears that line defects contribute very little to the electrical resistivity. There is some doubt, however, as to the validity of van Bueren's expressions for all cubic metals.' In fact, the data on copper and silver are not conclusive. In this in-

Jan 1, 1962

By C. Ernest Birchenall, Robert F. Mehl

APPLICATION of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion coefficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner1 derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smiths on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 ACTIVITIES IN BRASS9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by azn = Pza/Pzn° [I]

Jan 1, 1947