Search Documents

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,&apos; and his experiments have been described and summarized by Richards.&apos; White&apos;s contributions seem to have passed unnoticed by Fahrenwald,2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,&apos; USSR; Anselm and Grunder,&apos;, Germany: and Rose and Evans." Great Britain. Subcritical and Supercritical Speeds: In the formula of the critical speed given in the textbooks of mineral dressing, no factor indicating the coefficient of friction is generally included. If this factor = 1.0, which is equivalent to grinding conditions in a mill provided with heavily ribbed lining, the formula of the critical speed holds as such and grinding is possible at subcritical speeds only. In a mill equipped with a smooth or relatively smooth lining, the numerical value of the friction factor in the denominator of the formula becomes <1.0, indicating that grinding at supercritical speeds should be possible in such mills. It has been recently shown by the author&apos; that a wide supercritical speed range will become available for grinding—and especially for fine grinding—if the basic conditions within the mill have been selected properly. Mathematical analysis of mill dynamics at supercritical speeds&apos; has indicated that the mill speed may be increased if: 1) total mass of grinding medium decreases, 2) mass of the individual grinding piece increases, and 3) the coefficient of friction between the outer layer of medium and the mill lining decreases. It is obvious that the mass of the individual grinding piece will be affected by its shape and by its specific gravity. The coefficient of friction decreases with: 1) increasing smoothness of liner surface, 2) increasing roundness of the grinding piece, 3) increasing fineness of material to be ground, 4) decreasing pulp density, and 5) decreasing hardness (abrasiveness) of the mineral to be ground. In a mill equipped with heavily ribbed lining, practically no size reduction will take place between the lining and the outer layer of tumbling medium, because slippage is prevented. In the overwhelming majority of today&apos;s mills the grinding accomplished is by virtue of cataracting and/or cascading media with some action within the tumbling charge. Sub-critical speeds only can be applied. In grate-type or peripheral discharge mills equipped with a smooth lining a tumbling load of any kind of common medium occupying about 50 pct of mill volume will behave in such a way that practically no slippage will take place. This has been verified in experiments run by the author in the laboratory and in pilot plant mills&apos; equipped with smooth lining. Again, the operation is limited to the subcritical range. In a mill with a smooth lining, grinding will be possible either at subcritical speeds or within a wide supercritical speed range as soon as the basic requirements for a desired speed are fulfilled. In a mill operated at supercritical speed, any point on the liner surface proceeds at a speed greater than that indicated by the formula of the critical speed, while any grinding piece situated in the outer layer of the medium against the lining proceeds in the same direction at a speed less than that indicated by the critical speed. This speed difference produces a very effective attrition grinding zone between the liner surface and the outer layer of the medium. The share of attrition grinding of the total grinding accomplished increases rapidly with increasing speed in the supercritical speed range. The smooth surface of the mill lining may be well illustrated by the surface of a bucking board. The outer ball layer may be similarly represented by the lower surface of a muller. If the bucking board, the material to be ground, and the muller all proceed in the same direction at the same speed, no grinding will result. This is the general situation in the mills of today. If, however, the muller is pulled with respect to the board, moving or stationary, grinding will be accomplished effectively. Although grinding in today&apos;s mills is primarily the result of cataracting and/or cascading media, the principal place of grinding at high supercritical speeds will be the attrition zone.&apos; In the mineral dressing laboratory of the State Institute for Technical Research. Helsinki, Finland, large quantities of different ores have been ground in a pilot plant ball mill (3x3 ft) at a top speed about 230 pct of the critical. With the same mill, theoretical investigations concerning the grinding characteristics of ball mills equipped with a smooth lining have been carried out up to the speed of 313 pct&apos; of the critical. With a smaller mill, the grinding characteristics with a variety of grinding media have been investigated at speeds up to 2000 pct of the

Jan 1, 1959

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation&apos;s Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.&apos;s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,&apos; led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By R. E. Boehler, N. C. Ludwig

At Buffington Station, Gary, Ind., Universal Atlas Cement operates fourteen 8 x 101/2 x 155-ft cement kilns in mill 6 and two 11 x 360-ft kilns in the Harbor plant. The No. 11 and 12 kilns in mill 6 are equipped with Manitowac recuperator sections. This report describes studies in measuring exterior shell temperatures on several of these kilns and the development of a traveling radiation pyrometer with certain novel features. Preliminary Work: At first various temperature-sensing devices were placed on the steel shell: 1) crayons with calibrated melting points, 2) colored paints with temperature-calibrated pigments, 3) aluminum paints with temperature-calibrated binders, and 4) metal-stem dial thermometers. The colored paints and aluminum paints failed to indicate the temperatures correctly. The crayons and thermometers did indicate fairly correct temperatures, but it proved impossible to apply enough of these on the shell to detect all the potential areas where hot spots might develop. Furthermore, considerable labor was required to apply these sensors and read the temperatures. Consequently no further work was done with these devices. Formation of Hot Spots: In the burning or clinker-ing zone of a cement kiln, the thickness of the protective coating and thickness of the brick govern the amount of heat transmitted to the steel kiln shell. Usually the protective coating consists of 4 to 8 in. of fused cement clinker. The formation of a hot spot is usually caused by loss of coating? that is, localized areas of the coating become thin or fall away from the refractory. This is generally caused by excessive temperature in the burning zone over a fairly long period of time. It may also be caused by a sudden thermal change in the burning zone. Variations in raw feed composition and in feed rate require changes in the fuel and air rates, and when these are not appropriately altered, conditions may develop in the kiln that will result in loss of coating. Luminescence on the kiln shell indicates that a hot spot has developed to a point that usually alters the refractory&apos;s thermal conductivity properties. When this thermal weakness zone occurs in the burning zone of the kiln, constant vigilance is required to protect it by maintaining proper coating. Even so, it has been the writers&apos; experience that within a period of several days to about four weeks the hot spot usually recurs with greater severity. This necessitates shutting down the kiln and re-bricking the affected area. One of the prerequisites of a good burnerman is the ability to maintain a protective coating despite the many variables in operation. When he knows that it is getting thin or that an area has dropped off, he reduces the firing rate and kiln speed and brings feed into the affected area in an effort to rebuild the coating. But when powdered fuel is burned, the atmosphere of the kiln may prevent the burnerman&apos;s observing the condition of the coating closely at all times without taking off the fire. It is not considered good practice to do this frequently, as it imposes a thermal shock on the coating and upsets operation of the kiln. To help the burnerman scan the shell of the kiln along the burning zone, therefore, a radiation pyrometer, connected to a potentiometric recorder, was mounted on a slowly moving steel cable. The theory of operation, construction details, and adaptability of the radiation pyrometer are included in an excellent monograph&apos; and also in a textbook.&apos; Shell temperatures of the Atlas Cement kilns were measured with a Brown Instruments Div. low intermediate range Radiamatic unit, of range 200" to 1200°F, and a circular chart Electronik potentio-metric recorder, of range 500" to 1000°F. In Bulletin 59095M the supplier publishes standard calibration data (millivolts vs degrees Fahrenheit) for this radiation pyrometer, These data, however, apply only to flat surfaces having emissivities of unity. Calibration of Radiation Pyrometer for Use on Curved Surfaces: When applied to surface temperature measurements, the radiation pyrometer reading depends on the nature of the surface, the material of which it is composed, and also to some extent on the temperature of the surroundings. Although the present radiation pyrometer is designed to give a calibrated response under ideal (black body) conditions when used commercially, it must be calibrated empirically. The calibration procedure, given below, follows that described by Dike (Ref. 1, pp. 38-39). Calibration tests on plane and curved surfaces showed that the response of the radiation pyrometer was very

Jan 1, 1961

By Rollin A. Pallanch

THE Midvale mill of the United States Smelting Refining and Mining Company is situated on a flat site whose elevation is 50 ft above that of the Jordan River. Tailings are impounded in the area between the river and the flat upon which the mill and railroad switchyard are located. The water supply is pumped from the Galena canal which leads from the river at a point some ten miles to the south. The mill has a present capacity of approximately 1700 tons daily. It started out originally in 1926 as a 750 ton three-unit plant. The tonnage was gradually increased to 1200 tons by 1934, and in late 1935 a fourth unit was added. The accompanying flowsheet shows the principal equipment and how it is utilized. The ore is principally sulphide with varying degrees of oxidation, with individual lots ranging widely in both precious and base metal content. In each of the four individual units of the mill there will often be mixtures of as

Jan 1, 1948

By D. S. Jacobus

It is proposed to give in this paper an estimate of the cost at which carburetted and uncarburetted water-gas will have to he sold, in order to compete successfully for steam-boiler use with anthracite coal. The following are analyses of the gas direct from the generator, and of the same after it has been carburetted for illuminating pnrposes. Per cent. by Volumes. I. 11. Uncarburetted. Carburetted. Nitrogen,.4.69 2.5 Carbonic acid,.3.47 .3 Ethylene,....... 0 12.5 Oxygen,....... 0 .2 Benzole vapor,...... 0 1.5 Carbonic oxide,.36.80 29.0 Marsh-gas,.2.16 24.0 Hydrogen,.52.88 30.0 100.00 100.0

Jan 1, 1889

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author&apos;s reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By J. F. Smith, J. E. Davison

A value for the enthalpy of formation of z2 of -3.14 i 0.21 kcal per g-atom has been measured by the technique of acid solution calorimetry. This result is in quite good agreement with two earlier determinations by tin solution calorimetry and by direct reaction caloriinetry, and averaging of values determined from the three independent calorimetric techniques gives enhanced precision and accuracy with AHh8 (CaMgZ) = - 3.15 i 0.05 kcal per g-atom. For comparison with experimental data, values for the enthalpies of formation of CaMgz, SrMgz, and BaMgz of -9.8, -7.9, and -2.8 kcal per g-atom were estimated from a calculation based on the LVigizer-Seitz approximation as modified by Raimes for polyvalent elements. While complete quantitative accord between these calculated talues and available experimental data is lacking, nonetheless numerical accord is better than might be expected and, more importantly, parallel numerical trends are observed between experimental and calculated vnlues. WITHIN the past decade the enthalpy of formation of CaMg, has been determined a) from measurement of magnesium vapor pressures over binary Ca-Mg alloys,&apos; b) by solution calorimetry with liquid tin as the solvent,&apos; c) from measurement of hydrogen vapor pressures over ternary alloys of calcium, magnesium, and hydrogen,3 and d) by direct reaction alorimetr. The value from tin solution calorimetry is the most precise and is probably the most reliable, and this value is within the quoted uncertainties of the other three experimental results. The overall agreement among the four independent investigations is quite good, particularly so when the diversity of techniques is noted. On the basis of this agreement, CaMgz was chosen as a test material to evaluate the operation of a newly constructed apparatus for the determination of enthalpies of formation of intermetallic phases by acid solution calorimetry. This was believed to be a severe test because of the high chemical reactivity of both calcium and magnesium which reactivity presumably accounts for the fact that an early determination5 of the enthalpies of formation of Ca-Mg alloys by acid solution calorimetry yielded values significantly more negative than the four recent determinations. EXPERIMENTAL APPARATUS AND MATERIALS Experimental Apparatus. The enthalpy of formation of CaMg, was determined by measuring the difference between the heat evolved when dissolving the metallic compound and the heat evolved when dissolving equivalent amounts of unreacted metallic elements in hydro- chloric acid. This was done differentially with an apparatus consisting of twin calorimeters which were constructed to be as nearly identical as possible. The advantage of differential calorimetry is that systematic errors arising from the individual calorimeter design tend to cancel. A schematic representation of the apparatus is shown in Fig. 1. A dead air space around both calorimeters was provided by a large, thermally insulated jacket. Each calorimeter consisted of a 2-liter Dewar flask which was completely enclosed in a copper container. Each Dewar contained 1600 g of 2.5hr HCl to act as the solvent, and thermal effects resulting from solvent evaporation were minimized by covering the acid with 50 g of mineral oil. There was no detectable reaction between the acid and the mineral oil. Equivalent amounts of mechanical energy were added to the calorimeters through twin stirring rods which were driven at the same rpm by a single motor with the intent of the stirring being to maintain thermal equilibrium throughout the solvent. To calibrate the heat capacities of the calorimeters, known amounts of electrical energy could be added by passing measured voltages and currents for known times through submerged heaters, approximately 20 ohms, which were wound noninductively from Manganin wire. A 6-v storage battery was used as a power source, and a dummy heater was used as an exercise circuit to allow the battery to stabilize at a constant electromotive force before energizing one or the other of the calorimetric heaters. A type K-2 potentiometer was used to measure the potential drop across an energized heater while the current was determined from the potential drop across an external standard resistor. Times of energization were measured with an electric timer, and the electrical energy supplied to a heater

Jan 1, 1969

By W. J. Taylor

Nature has furnished us with fuel in three forms, solid, liquid, and gaseous; solid, the most common; liquid, containing the greatest energy; gaseous, the most convenient for use. The tendency of the day is to the conversion of solid and liquid fuel into the gaseous form. There is magic in the word gas to many men who through ignorance or indifference imagine that by mere conversion into gas an immense quantity of energy can he added to fuel of other forms, forgetful of the law of nature, that. the conversion of any substance from one form to another involves a loss of effective energy, and therefore that if in certain cases more duty can be obtained out of the gas resulting from a given amount of coal than the coal itself will supply when used direct, the cause lies solely in the more efficient utilization of the fuel in its gaseous state. Nevertheless, new processes for making gas are constantly crowded upon our notice with claims of less cost for manufacture and delivery than natural gas, and often of far more energy for the product than is contained in the coal or oil from which it is made. I was recently asked to examine a new process of this kind. From an analysis shown me the calorific energy of the gas approximated 375 heat-units per cubic foot; on ascertaining the quantity of gas claimed to be made from a given amount of solid and liquid fuel, it appeared, that for every 325 heat-units contained in the latter 900 heat-units were alleged to he delivered into the gas, or nearly three times as much energy as the original fuel really held. The extravagant claim of some oil-gas advocates is still frequently heard, that by vaporizing oil with steam and then passing the mixture through a coil of hot iron pipe, an oil-water-gas containing 26,600 heat-units is formed from 1 pound of oil carrying originally 21,000 heat-units, while the only energy expended on the gas has been by the introduction of a -little steam and a little extraneous heat. Theoretically, 1 pound of oil converted into water-gas carries 26,600

Jan 1, 1890

Howard N. Eavenson, Gary, W. Va. (communication to the Secretary*):—For some time before the publication of Mr. Scholz&apos;s paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting to the Institute my results in the form of a discussion. It has long been a matter of common opinion among mining-men that mine-explosions are more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more inclined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what otherwise probably would have been small explosions. To show the difference in mine-conditions during summer and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas coal-region, in McDowell county,w.Va., the first one being a shaft-mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jan 1, 1910

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939

Rooms With Bath Rooms Without Bath Name Location Double Single Double Single Astor Times Square, 43d St. and $5.00 up $4.00 up $4.00 $2.50 up Broadway Belmont 42d St. and Park Ave. 6.00 up 5.00 tip 5.00 3.00 up Breslin 29th St. and Broadway 5.00 up 2.50 up 4.00 up 2.00 up Hermitage 42c1 Street and Broadway 4.50 up 2.50 up 3.50 up 2.00 up Imperial 32d St. and Broadway 4.50 up 3.00 up 3.50 up . 2.50 McAlpin 34th St. and Broadway 4.00 up 3.00 up 3.50 up 2.50 up Manhattan 42d St. and, Madison Ave. 6.00 tip 4.00 up 4.50 up 3.00 up Martinique 32d St. and Broadway 4.00 up 3.00 up 3.00 up 2.00 up Monticello 35 West 64th St. 2.50 up 2.00 up Navarre 38th St. and Seventh Ave 3.00 up 1.50 up 2.50 tip 1.50 up Plaza 58th St. and Fifth Ave. 6.00 up 4.00 up, Prince George.... 28th St. anti Fifth Ave. 3.00 up 2.00 up York 36th St. and Seventh Ave. 3.50 2.50 up 2.50 1.50

Jan 1, 1919

By Jack C. Haptonstall

Abstract-Minas de San Luis, S.A. operates the old Tayoltita mine located in the Sierra Madre Occidental in Durango, Mexico. Yearly production is 55 000 kg (1.7 million troy ox) of silver and 1000 kg (31,000 troy ox) of gold from milling 165 000 t/y (181,900 stpy) obtained from fissure veins. A 4.4 km (2.75 miles) adit, to intersect the veins below existing workings, was completed in 1974. The adit and ancillary projects facilitated extensive mechanization of the mine, ramp development of it, integration of duplicate facilities and elimination of obsolete facilities. It provided a deep-level access for exploration and development of the veins, and resulted in a 25% increase in production with the same labor force. The cost of the in-house financed project was $3.4 million.

Jan 2, 1978

By VlNTON H. CLARKE

Diamond-drill blasthole sloping has now been used for a long enough time to permit us to discuss fairly its problems from the ore-breaking angle and to attempt to peer into its future. To do this we have gathered information from many properties through questionnaires. The operators have indicated fairly well in their answers what they think of the method. The many variations of methods have by now been fairly well developed, and performance rates and. mining costs are well established at each property. All this can be laid down on paper with fair completeness. Now. knowing all this, what will the future of the method be? To attempt to look into the future of a mining method immediately brings to light many problems and variables. For instance: why were diamond drills used in the first place? What has the cost trend been? In what type of deposit has the method proved most advantageous? What will the future cost of diamonds be? What are the possible substitutes?

Jan 1, 1949

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By R. M. Rose, K. A. Jones

Resistive measurements ulere made on superconducting niobium single crystals in transverse magnetic fields. Crystals were grouln in both high and ulfrahigh vacua, doped with stnall quantities of oxygen, and annealed in ultrahigh vacua at temperatures from 900&apos; to 1350°C. Maxima in the fluxoid pinr~ir~g force were observedfor the [100] and [210] directions. The increase of the critical current density with dissoved oxygen was seen to saturate at relatively low concentration. This behavior, and the variation of J, and residual resistivity (as a function of oxygen content and annealing) of both clean and dirty gassy) crystals, is seen as a consequence of the formation of clusters with (210)~b habit planes and (200)ffo common boundaries. These suboxide clusters are apparenlly stable at high temperatures and very low oxygen concentrations. It is generally known that dissolved oxygen at concentrations well below the solubility limit sharply increases the critical current density of superconducting niobium.&apos; Such a result would not be expected if Nb-0 solutions were random, not even as the result of segregation on the scale usually encountered in solid solutions. According to the Kim-Anderson theory of flux creep,&apos; the critical transport current density is determined by the pinning force Fp associated with some feature of the microstructure. As the Lorentz force. a or (J X R), of the transport current in the magnetic field approaches Fp, flux creep and then flux flow occur. The pinning force is expected to be quite small if the heterogeneity involved is significantly smaller than tte range of coherency which for niobium is circa 250~.~ Although the strain field of an individual oxygen atom in the niobium lattice is relatively large, it does not seem plausible that individual atoms could be so effective as to account for the data. Also, ~ramer~ found that straining and strain aging specimens containing small amounts of oxygen on occasion decreased the residual resistivity. A possible explanation for the above behavior may be found in the work of van Ooijen and van der Goot,= who found that annealing changed J, for niobium foils containing oxygen, and they attributed the changes to ordering of the oxygen atoms. This phenomenon has been observed by other investigators using X-ray and PROCEDURE Cylindrical 4-in.-diam niobium single crystals with axial orientations [ill], [110], [112], and [oo~] were grown from pure niobium, see Table I for analysis, in an ion-pumped ultrahigh-vacuum system using the electron beam floating zone technique. Total pressure during growth was lo-&apos;9 torr: the oxygen partial pressure was less than lo-" torr, as determined by a mass spectrometer. These crystals will be referred to as the "clean" crystals. Similar crystals were also grown in another system at a pressure of 5 X 10"6 torr. These crystals will be referred to as the "dirty" crystals. Specimens 14 in. long were cut from the as-grown crystals and one end was polished down to no. 600 carbide paper smoothness. A back-reflection Laue photograph was then taken in order to fix the crystallo-graphic directions transverse to the crystal. The critical current density J,, the current density necessary to produce a voltage drop of 1.0 pv between voltage leads placed a in. apart, was determined as a function of the magnitude and direction of the transverse magnetic field and of the oxygen concentration. The technique and experimental arrangement was essentially similar to that of Tedmon et al.&apos; In the remainder of this paper, the azjmuthal angle $ for the field H is referenced to the [ I101 direction in all four crystals, and oxygen was added in small equal increments by anodization and annealing.7 The resistivity ratio, RR, of the resistance at room ternperature to that at 4.2"K (H =7.00 kG) was determined as well.

Jan 1, 1970

By J. Nutting, D. H. Kirkwood

IT is clearly of great metallurgical interest to know the conditions of temperature and gas composition under which different products will form in sulphide roasting. A method of graphically presenting the relevant thermodynamic data will be demonstrated, such that these conditions are readily obtainable. The products of sulphide roasting may be oxide, sulphate, or oxysulphates, and the equilibria between these may be represented in the following way: 2 MSO4 = MOMSO4 + SO3 MO-MSO4 = 2 MO + SO3

Jan 1, 1961

By H. C. Casey, M. B. Panish

The roles of the phase diagram and the diffusion and solubility analyses in the selection of sources for the diffusion of zinc into GaAs are discussed. Isothermal sections of- the phase diagram are described at 1000°, 775°, 744°, and 700°. Below 744° the three solid phases, Zn3As2, GaAs, and ZnAsz, may be in equilibrium. In the composition regions where the three solid phases are in equilibrium, the partial pressures of the components do not vary with composition and there is no liquid phase. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected to yield reproducible diffusion profiles without surface damage. The 5/50/45 ternary source Provides a significant improvement in the reproducibility and planarity of- the zinc diffusion as compared with other zinc diffusion sources that result from starting with elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. Several experimental diffision profiles for the 5/50/45 diffusion source have been determined. The profiles are very steep in the region of the junction and produce devices that exhibit step junction behavior. The junction depth varies as the square root of time. Diffusion at 700°C for 4 hr gives a 5-µ junction depth and a surface concentration of 2.4 x1020 cm-3. The surface concentration is enhanced by a factor of three and the junction depth decreased by a factor of ten as compared with diffusion with a starting source 01- elemental zinc. The differences in dijyusion behavior with these two sources are due primarily to the approximately 10&apos; greater equilibrium As4 partial pressure for the 5/50/45 source. ThE most common technique for the preparation of GaAs p-n junctions for diverse applications ranging from switching diodes to injection lasers has been to diffuse zinc into the solid from the vapor phase. The zinc impurity has generally been provided by introducing into a diffusion ampoule elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. For the purpose of eliminating surface deterioration, zinc has been diffused into GaAs through SiO2 films1 and from zinc-doped SiO2 films.2 During a study of the injection and recombination mechanisms in GaAs junctions, we found that these diffusion techniques either resulted in nonreproducible diffusion profiles and nonplanar junction interfaces or were extremely inconvenient to use. An unpublished report by Allen and pearson3 emphasized that an understanding of diffusion requires relating the diffusion conditions and system compositions to the ternary phase diagram. Recent studies have made it possible to relate the effect of starting source composition on the GaAs sample surface and diffusion profile reproducibility and, in addition, to estimate the expected surface concentration and zinc diffusivity. These studies include the Ga-As-Zn phase diagram,415 the determination of the incorporation reaction for zinc as a substitutional impurity,6 and the analysis of the concentration dependence of the diffusion coefficient.&apos; In this paper the role of the phase diagram in the selection of the starting diffusion source composition is illustrated, and an application of the diffusion and solubility analyses is used to demonstrate their utility in the estimation of surface concentration and diffusivity for various starting source compositions. Consideration of the isothermal sections of the ternary phase diagram shows that below about 744° C a composition region exists where the three solid phases Zn3As2, GaAs, and ZnAs2 are in equilibrium without a liquid phase. In this region the partial pressures of the components do not vary with composition, and thus the surface concentration and diffusivity depend only on temperature. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected. As will be described in detail, this diffusion source yields reproducible diffusion profiles without surface damage, planar junction interfaces, and steep profiles that result in devices with step junction behavior. Only closed diffusion systems are considered. Open or flowing vapor systems require the maintaining of constant vapor pressures in the flowing gas and represent control problems outside the scope of this discussion.

Jan 1, 1969

By M. C. LAKE

THE industrial development of the United States has been stimulated by the presence of high-grade iron ore in the Lake Superior district. These great deposits have been susceptible to economical extraction and are conveniently located for cheap lake vessel transportation to the great consuming centers. The district furnishes from 80 to 85 per cent of the iron ore annually consumed in the United States, and a full understanding of the available supply of this great commodity is so important that it is well to consider whether or not the industrial supremacy and national independence attained as a result of the abundance of cheap ore are permanent. The enormous deposits of high-grade ore available in the Lake Superior district have been the foundation upon which the vast industrial structure of the steel and allied industries has been built. It is extremely important to the country as a whole, and especially to those States and communities now dependent on Lake Superior ore for their prosperity, that their industries shall retain the particular advantages with which they are now endowed, and that a generous supply of high-grade raw material be available for their consumption at a satisfactory cost. The steel industry is so basic and fundamental that any fluctuation in the cost of its finished products as determined by the supply and cost of the raw materials involved in its manufacture will necessarily affect the business of a wide variety of industries which are dependent on it.

Jan 1, 1926