Search Documents

By A. U. Seybolt

A. U. Seybolt (General Electric Research Laboratory)— As pointed out in an earlier paper,41 it appears to be very difficult to nucleate Si3N4 in Si-Fe of silicon content up to around 5 pet. Therefore, one observes, as did Pearce, that equilibrations with nitrogen gas yield only nitrogen in solid solution at temperatures above about 700°C, or, as Pearce found, 770°C. Evidently, the free energy of formation of Si3N4 only becomes high enough at -770°C to overcome the reluctance of Si3N4 to nucleate. However, as mentioned in Ref. 41, if some Si3N4 is first formed by a mixture of ammonia and hydrogen, one can then replace this gas mixture by nitrogen gas, and either increase or decrease the amount of Si3N4 present at any temperature by suitable adjustment of nitrogen pressure: that is, to equilibrate with Si3N4. In the equilibration experiments cited in Ref. 41, equilibrium was approached from both sides, and it was found that samples up to 944oC, at least, were in equilibrium with Si3N4. Higher temperatures were not employed, as this would have necessitated a redesign of the apparatus for using nitrogen pressures in excess of 1 atm. To summarize, the results of Pearce's experiments and those of Ref. 41 cannot be directly compared because two quite different equilibria were studied. Therefore, the statement by Pearce on p. 1398 indicating apparent error in Ref. 41 is unjustified. M. L. Pearce (author's reply)— There was limited evidence obtained in the current investigation which would indicate that excessive "supercooling" did not occur. A small piece of the same resulting from heat treatment No. 5 in Table III was subsequently held at 800°C for 16 hr in 95 pet N-5 pet H. Isotope-

Jan 1, 1964

By F. H. Froes, D. H. Warrington

Electron microscope evidence which indicates that TaC may precipitate at random sites in the matrix is presented. Initially the particles are almost spherical and coherent with the matrix. However, as they grow in conditions in which there are insufficient vacancies to relieve lattice strain, the particles rapidly lose coherency in two directions and continue to grow as plates with approximately the full lattice mismatch strain present perpendicular to the plane of the plate. The necessary relief of strain comes from dislocations loops which do not become visible until the later stages of aging. The rapid decrease of apparent strain to low values of appoximately 1 pct at small particle sizes arises not from a complete incoherency but from applying a model wrong for the particle shape and strain distribution. PREVIOUS work has shown that MC-type carbides may precipitate intragranularly in austenitic stainless steel on dislocations,1&apos;2 in association with stacking faults,3&apos;4 and randomly through the matrix,5-7 In investigations of the matrix precipitate by thin-foil electron microscopy, considerable lattice strain has been found to occur around the precipitating phase.7&apos;8 Attempts have been made to evaluate the amount of lattice strain by using the methods developed by Ashby and brown.9,10 Values of the linear strain, much less than the 17 pct theoretical mismatch (for TaC), have been reported; it has been suggested that this is due to either a loss of coherency1&apos; or vacancy absorption which occurs during either the initial nucleation or growth of the precipitate." This report is an extension of earlier work7 that dealt with the precipitation of TaC from an 18Cr/12Ni/ 2Ta/O.lC alloy after it had been quenched from 1300°C and aged between 600" and 840°C. In particular, the shape of the precipitate particles and the amount of strain in the matrix, due to the precipitate, have been studied. The work described here is part of a wider investigation of factors that affect carbide precipitation in austenitic stainless steel," details of which are to appear elsewhere. RESULTS The present investigation can be conveniently split into two aspects of the strain-fields surrounding the matrix particles: 1) information derived from the strain-field which indicates the shape and habit plane of the precipitate particles and 2) the magnitude and sign of the strain-field. The Shape and Habit Plane of the TaC Precipitate. In the early stages of aging twin lobes (normally black F. H. FROES, formerly at the University of Sheffield, Sheffield, England, is Staff Scientist, Colt Industries, Crucible Materials Research Center, Pittsburgh, Pa. D. H. WARRINGTON is Lecturer, Department of Metallurgy, University of Sheffield. Manuscript submitted November 1, 1968. IMD on white background, i.e., for the deviation parameter, S > 0) that indicate the strained region of the matrix define the position of the particles by bright field transmission electron microscopy. The actual particles were not detected until they were approximately 120Å diam; below this size they were too small to be imaged in the electron microscope. This meant that particle growth that had occurred before this stage had to be inferred from the matrix strain-field contrast. In all cases when diffraction effects were observed from the precipitate particles, a cube-cube orientation relationship (i.e., (llO)ppt Il<llO>matrix and {1ll }ppt {III} matrix) existed between the precipitate and the matrix. From the matrix precipitate particles lying along edge-on {111} planes (e.g., at A, Fig. I), the precipitates are seen to be plate-like with their diameter being roughly 18 times their thickness after 5000 hr at 650°C. However, the exact shape of the particles cannot be determined because of the masking effect of the strain-field contrast. If a dark-field micrograph, using a precipitate reflection, is studied, Fig. 2, a number of the projected images of the TaC particles [on the (110) foil surface] apear to have straight edges parallel to projected f111) planes. Thus, it appears that in the later stages of aging the TaC particles are plate-like with some tendency for the edges of the plate to be bounded by the matrix close-packed {ill} planes (though the general shape of the particles in the plane of the plate is circular and thus the "diameter" of the particles has a real physical significance). It should be noted that the bands of fine discrete particles observed in Figs. 1 and 2 are not the matrix precipitate discussed in this paper but are precipitates associated with extrinsic stacking faults3j4 occurring on (111) matrix planes. **£** ****** \ *x 23 Fig. 1—18/12/2~a/0.1~ alloy. Solution treated at 1300°C for 1 hr, water quenched, and aged 5000 hr at 650°C. The (112) directions shown are the traces of the e&e-on (111) planes. Foil normal [110]; operating reflection (331); bright field micrograph.

Jan 1, 1970

By Wallace E. Pratt

TO SERVE their primary function of balancing supply with demand. crude-oil prices must not only return full cost plus a reasonable earning to the efficient producer but they must also offer an additional reward to stimulate exploration sufficiently to maintain adequate reserves. High prices increase the volume and efficiency of exploration; low prig e- -Idle exploration. Over the last decade average prices for crude oil have been much lower than for the proceeding ten years, and lower even than the average over the life of industry. Under these circumstances no one should be surprised to learn that over this same recent period of discovery of new oil fields has also lagged and fallen below its average level for the previous decade. Crude oil prices have been too ion to support the required activity in wildcatting.

Jan 1, 1941

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.&apos; Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

By Robert W. Hunt

THE memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444 ; 17,628, re¬issued as 505; 18,910, dated January 10th, 1857 ; June 23d, 1857; November 3d, 1857; and December 22d, 1857, respectively. This association was composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. Z. S. Durfee to England, to secure for this country Mushet&apos;s patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer&apos;s inven¬tion, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer&apos;s American patents. Mr. Holley returned to England in

Jan 1, 1877

By R. J. Cowan

IN the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as "catalytic," "atomic," "nascent" and "activated;" in an attempt to describe the process. These words are used indiscriminately. For, instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process.

Jan 1, 1931

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,&apos; or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By A. G. Jordan, W. Jeitschko, Paul A. Beck

The occurrence qf the V phase structure /Zr,Co,Ge, type) in ternary syste7ns (titanium, zivconium, niobium, lanta1urn) -(nickel, cobalt, iron)-(silicon, germanium) was incestigated. Nine V silicides and four V gertrlanides were found and their lattice constants are reporled. The lattice constants of twenty-one preri-ously identified E phases (TiNiSi type) are given. The average atomic volumes of these phases are discussed in relation to similar binary phases. ThE occurrence of a phase Ti4Ni4Si7 was first reported by Westbrook. DiCerbo, and peat&apos; who gave it the name "V phase". They also reported the existence of an E phase TiNiSi. Subsequently a systematic study was undertaken in this laboratory to explore the occurrence of E&apos; and V phases3 in related ternary systems. In the meantime the crystal structure of the E phase TiNiSi 4 and of the V phase Zr4CO4Ge 75,6 was determined. In the present paper the details of the V phase investigation and the lattice constants of the E and V phases are presented. V PHASES Alloy specimens of approximately 10 to 15 g were prepared by arc melting under argon (99.996 pct Ar) atmosphere. The starting materials were all of purity higher than 99.9 pct, with the exception of cobalt. which contained 0.14 pct Fe as the only major impurity. The weight losses were in all cases less than 2 pct, in most cases less than 1 pct. The samples were encapsulated in fused silica tubes with sufficient argon to yield about 1 atm pressure at the annealing temperature. After the homogenization anneal. Table I. the specimens were water-quenched. A representative portion of each specimen was then examined metallographically (etchant: 20 pct HNO,. 10 pct HF. 25 pct glycerine, 45 pct H20). Only minor amounts of second- and third-phase particles were observed in the specimens listed in Table I, with the exception of alloys Zr4Fe4Si7 and Ta,Fe,Si,. which contained an estimated 10 pct by volume of foreign phases. X-ray powder photographs were taken with a Seeman-Bohlin type focusing camera and Fe-KO radiation. Of the thirty possible combinations of elements in the ternary systems (titanium, zirconium. vanadium. niobium. tantalum)-(iron. cobalt, nickel)-(silicon. germanium) thirteen V phases could be identified. In the remaining seventeen ternary systems and also in the systems Cr-Ni-Si and (M0.W)-(Ni.Co)-Si no V phase was found at the composition 4:4:7 after annealing at temperatures between 900" and 1200&apos;C. For the determination of the lattice constants of the V phases Debye-Scherrer photographs were taken using the asymmetric film arrangement and CrKcr radiation (ka1, = 2.28962A). Using the positional parameters, as determined6 for Zr,Co,Ge,. Table 11. intensity calculations were carried out for each of the V phases with the aid of a computer program.: Thus unequivocal indexing of the diffraction patterns was greatly facilitated. The lattice constants. Table I. were then computed by a least-squares fit of the high-angle lines with f (0) = cos2 Q as extrapolation function. Only few. if any. very weak impurity lines were observed, with the exception of the three iron alloys Zr,Fe,Si7. Zr4Fe,Ge7. and Ta,Fe,Si7. The agreement

Jan 1, 1970

The economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.—The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By M. C. Lavine, H. C. Gatos, R. S. Mroczkowski

The structure of GaAs-Ge heterojunctions prepared by a back-melting process was studied by X-rav diffraction, melallographic, and electron-micro-analyzer techniques. The boundary region between the GaAs and the germanium was found to consist of a four-layered band. A discontinuity between the two inner bands was brought about by solidification occurring simultaneously from the GaAs and the germanium side. The junction material OH either side of the central discotinuity was found to have grown as a single Crystal with the orientation of the parent substrate. It was found essential to determine the GaAs-Ge phase diagram. This was accomplished by a series of alloys containing 0 to 40 wt pet GaAs. Over this range the diagram is a simple eutectic with the eutectic point at 74 wt pet Ge and 845 C. The limiting- solubility of Coils in germanium was found to bc less than 5 wt pet. The Kossel divergent-beam X-ray technique was used to study orientation relationships across the boundary lager. A great deal of effort has been recently expended on the electrical properties of heterojunctions. Little attention, however, has been given to the metallurgical variables which may be of importance in the formation of the junctions. The present work was undertaken to investigate some of the more pertinent metallurgical aspects of interface-alloyed GaAs-Ge heterojunctions. Such parameters as solidification processes, composition gradients, orientation effects, and the accommodation of crystal structures have been the objects of study in this program. EXPERIMENTAL PROCEDURES Phase Diagram. The phase diagram of the GaAs-Ge pseudobinary system was determined by means of cooling curves. A Bridgeman furnace was employed with the center section maintained at 1200°C and the upper section at 800°C. Melts varying from 0 to 40 at. pct in GaAs content were used. Each charge was incapsulated under a two-thirds atmosphere of argon in a carbon-coated quartz tube. Five min in the furnace hot zone provided rapid melting and homogenization. The capsule was then removed to the cooler portion of the furnace. Cooling times were of the order of 3 min. The resulting homogeneous microstructure indicated that equilibrium conditions were obtained by this procedure. Formation of Heterojunctions. Rectangular parallelepiped single-crystal samples were cut with the large faces of either the (l00), (110), or (111) orientation. The remaining four surfaces were also cut to specific orientations to permit accurate relative orientation of the GaAs-Ge pairs. The

Jan 1, 1965

By John E. Hagni, Richard D. Hagni

ORE.ID, a microcomputer program, rapidly searches a database of the principal properties for 573 ore minerals. Searches may be performed on any or all of the following properties: mean Vickers hardness, Talmage hardness, mean reflectance, strength of anisotropism, and colors and tints of the mineral and its internal reflections. Data from the International Mineralogical Association - Commission on Ore Microscopy data card file have been used when available. The program displays the number and type of data matches for each mineral found, displays their chemical components, and allows the range to be narrowed or widened for each of the identification properties for repeated searches, if desired. ORE.ID is much more rapid, allows for the use of more identification properties, and involves more ore minerals than any previous identification system.

Jan 1, 1985

By C. A. Zapffe, C.E. Sims

Many hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel.l05 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlelnent is due to hydride formation aoes not conform to the known facts.l04 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not Yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel.

Jan 1, 1941

By C. E. Sims, C. A. Zapffe

Many hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel.l05 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlelnent is due to hydride formation aoes not conform to the known facts.l04 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not Yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel.

Jan 1, 1941

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today&apos;s competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don&apos;t build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD&apos;s cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962

By Charles S. Barrett

There is a road into the microscopic realm that has remained untraveled through all these years of intense activity with high-power optical and electron microscopy. The road is worthy of careful scouting by metallurgists and other investigators, for it leads into relatively new country and it makes some areas accessible that heretofore could be reached only by very indirect paths or by the use of imagination. And when the road passes through familiar territory it frequently permits a new view of commonplace things that should prove of value from time to time. An accepted way to interest people in new sights such as this is to present an illustrated travelogue. This I propose to do, using many pictures taken in my recent exploration of this road. In the manner of travelogues, I shall touch briefly upon a large number of different subjects in physical metallurgy and shall attempt to give an exhaustive treatment of none, for the objective is to provide a means for further research, to interest others in it, and to indicate what appears at the moment to be profitable directions for it to take. The method I shall present involves X-rays, but does not make use of the usual accompaniments of X-ray research such as reciprocal lattices, Fourier series, or the stereographic projection. The method is so simple in its fundamentals that it could have been developed 2o years ago, or perhaps even 30 years ago. It is well to have a destination for our travels, so that when we are through we shall have explored some region of importance, despite our preoccupation with the novel means of transportation and our interest in the sights to be seen along the way. So let us name the Cold-worked State as our destination, and make side trips into the territories known as Recovery, Recrystallization, and Precipitation-hardening. A great many investigations have been made of the nature of cold-worked metal, and a great variety of methods used, many of which are indirect, such as X-ray line intensities, X-ray line widths, calori-metric measurements, and magnetic measurements. Since comprehensive reviews of these investigations have been published in recent years, they need not be discussed here. The investigations that were the direct forerunners of the present work should be first mentioned. In 1931 I became interested in the structure of individual spots in X-ray diffraction patterns.l When a crystal is placed in the narrow pencil of X-rays in a Laue camera, the spots recorded on the film are not always uniformly black, but may have an internal structure. The meaning of this may be understood from Fig. I, which represents a narrow beam containing X-rays of many wave lengths (&apos;&apos;general radiation") penetrating a crystal in the direction of the arrow and forming a pattern on the vertical film at the right.

Jan 1, 1945

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200&apos; C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

By Charles R. Keyes

I. INTRODUCTORY. IN the dry regions of the globe many silver-deposits display certain remarkable features which at the same time are so totally unlike anything met with among ore-bodies elsewhere, that they have long presented exceptional difficulties not only to a satisfactory explanation of their origin, but to economical milling. A most striking peculiarity of these ores is the haloid character of many of their bonanzas. To this fact more than to any other may be ascribed most of the unusual uncertainties of mining-operations in desert countries-the marvelous local richness of the ores under certain conditions and the often abrupt transition, to utter poverty; the inadequacy of ordinary prospecting customs and the constant devising of new exploratory methods; the unaccountable losses in smelting and the continual change in treatment-practice. For these anomalies certain climatic conditions seem to be chiefly responsible.

Jul 1, 1911

Edward Keller, Baltimore, Md. (communicatioin to the Secretary*):—It is pleasing to note the increasing amount of work on metallurgical problems that is being carried on by exact scientific methods, and the results of such labor issued by the laboratories of our universities. Without doubt, Mr. Bolles&apos;s paper will be welcomed by all progressive practitioners. Many of the results which Mr. Bolles presents to as are new; and I take exceptioil to a few minor points only. The first of his concluding remarks is as follows: "Mattes are not homogeneous, but are composed of distinct mineral entitier, and may be likened to igneous rocks, in which the mineral constituents fall out upon the lowering of the temperature and ensuing solidification." He quotes an introductory remark to a paper1 of mine, as follows: "The true chemical character of copper-mattes does not yet seem to have been definitely determined, i.e, it is still more or less of an open question whether they are true chemical compounds, or mixtures, such as igneous rocks." This quotation, taken alone, would convey the impression that Mr. Bolles&apos;s conclusion is entirely new. Had he quoted also another paragraph from my paper in question, it would be clear that he was, to a certain extent at least, anticipated. I take the liberty, therefore, to state the substance of my own work. In the paper referred to, I showed the existence of the phenomenon of liquation in mattes, and, continuing, said: " A more direct method to test whether a matte is a compound sulphide or a mixture of individual sulphides was attempted by applying hydraulic separation. A clean piece of matte was selected containing practically no magnetic oxide and of the following composition: Cu, 37.96; S, 24.45; Fe, 33.63; Zn, 1.25; Pb, 1.02 ; Sb, 0.26 ; As, 0.065 ; insoluble, 1.15 per cent. ; Ag, 26.7 ; Au, 0.04 oz. per ton. For such a test it is essential to select a chemically uniform piece, other-

Jan 1, 1905

By G. Sachs, G. Espey

IT is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.1-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.1-6, It has also been observed that higher stresses are set up by the use of wide-angle dies than by the use of acute dies.2 The actual stress distribution in drawn .tubing has been investigated by a few workers,7-9 but has not been related to the conditions of the drawing process: Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal.1-10 MATERIALS AND PREPARATION The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.‡ This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2 -in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during sinking, as previously observed 4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation method1,11 of splitting a certain length of tubing was employed to obtain a bird&apos;s-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring on splitting. For the determination of the complete stress

Jan 1, 1941

By J. Burns Read

IT IS the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnance Department, during the War, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Ordnance Department in obtaining these data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The manufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodicals and, therefore, will not be given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540° to 650° C. (1000° to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases are then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followed, by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430° to 480° C. (800° to 900° F.) by immersion in a salt bath or by gas flames. After being washed, the cases are tapered, when they are ready for machining, inspection, and testing.

Jan 4, 1922