Search Documents

By Arnulf Muan, R. E. Johnson

Equilibrium CO2 /CO ratios of a gas phase coexisting with selected oxide phase assemblages of the system CaO-"Fe0"-SiOz and vnetallic iron have been determined at 1080°C. The data obtained are used to calculate activity-conzposition relations for metasili-cute, orthosilicate, and CaO- "FeO" solid solutions, and to determine a new value for the free energy of formation of C&S&0,. The metasilicate solution is practically ideal, whereas large deviations from ideality exist in the othe,r two solid solutions. BECAUSE of the geochemical and metallurgical importance of the oxides CaO, "FeO", and SiOz, the system CaO-"FeO"-SiO2 has been the subject of several experimental studies during the past 30 years. Following the delineation of phase relations at liquidus temperatures by a group of investigators at the Geophysical Laboratory of the Carnegie Institution of Washington in 1933,1 Chipman and associates in the early forties2,3 determined activities of FeO in liquids of this system. Since that time, many attempts have been made to interpret the data of Chipman et al. in terms of the constitution of the silicate liquids and the interaction parameters among the various constituents of the system (see for instance papers by Richardson4 and by Flood and coworkers5). One of the assumptions made in some of these interpretations4 is that the binary silicate systems CaSiO3-FeSiO3 and CazSi04-Fe2SiO4 mix ideally in the solid state. The objective of the present study is to provide experimental data on activity-com position relations in solid solutions of the system CaO-"FeO"-SiO2. Such data will contribute toward an understanding of the thermodynamics of silicate solid-solution phases in general, and will serve specifically to confirm or refute some of the assumptions made in interpreting liquid slag behavior. PREVIOUS WORK Phase relations in the system CaO-"FeO"-SiO2 in contact with metallic iron were determined by Bowen, Schairer, and Posnjak,1 and additional phase-equilibrium data for this system have been presented by Allen and snow.' A reproduction of the most up-to-date phase diagram for this system is shown in Fig. 1.7'8 Of particular interest in the present investigation are the relations among the various crystalline phases slightly below the lowest solidus temperature in the system, as shown in Fig. 2. The present work will be concerned primarily with some of the composition

Jan 1, 1968

By D. K. Crampton

NEARLY everyone who has not had the benefit of study in the field of metallurgy subscribes to a persistent and enthusiastic belief in the legendary lost art of hardening copper. This of course supplies a perfect introduction to a chapter of information on copper and its alloys, since the dissipation of fallacies and superstitions affecting an art probably constitutes the best method of getting at its real substance. Metals are hardened, but also embrittled, by a plurality of impurities. In the modern technology of copper-base metal products, we are familiar with a great host of materials, passing from one extreme of dead soft copper better than 99.9 pct pure, which in the form of wire about as thick as a match will stand hundreds of full twists in a 12-in. length, to an alloy containing less than 3 pct of alloyed substance possessing the strength of pretty good steel and capable of manufacture into razor blades, should we suddenly be deprived of steel; certainly a much better material for this purpose. Every copper alloy known to primitive man lies in some inter- mediate position and the ancient bronzes that have been found all over the world wherever an early civilization existed are usually contaminated by such impurities as sulfur, oxygen, antimony, arsenic, iron, or other materials, so that they could not possibly conform to any modern intelligent specification insuring the best combination of useful properties in alloys of their type and would go

Jan 1, 1953

By Maurice L. Pinel, Thomas T. Read, Thomas A. Wright

THE erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1,11,12 but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until more and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: 1. 502 A.D. A pair (right and left) of recumbent lions (Fig. 1). Base 7 ¼ by 14 3/8 in., height over-all 5 ½ in., weight 26 lb. each. The translation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third year of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

Fred. T. Greene, Rossland, B. C. (communication to the Secretary): At the beginning of his gaper, Mr. Herzig refers to an article of mine in the Engineering and Mining Journal of January 27, 1900. I would like to add that the method de-

Jan 1, 1901

By R. A. Meussner, R. T. DeHoff, F. N. Rhines

ZINC diffuses through copper more rapidly than does tin. Accordingly, when a ternary diffusion couple is made, by bringing an 0 copper-zinc brass into contact with an a copper-tin bronze at fixed high temperature, it is to be expected that zinc will diffuse into the bronze faster than tin diffuses into the brass. Adjacent to the brass side of the couple the total alloy content (zinc plus tin) should diminish, therefore, while next to the bronze side the alloy content should increase. Since the path of compo- sition change must be continuous, in a single-phased alloy, it should follow a curved and, in general, an S-shaped course. The realization of this prediction is demonstrated in Fig. 1, where the composition paths of two ternary diffusion couples are plotted on the appropriate isotherm of the copper-tin-zinc phase diagram. The diffusion couples were both made from a binary copper-tin alloy analyzing 5.0 pct tin placed against binary copper-zinc alloys analyzing 18.9 and 29.3 pct Zn, respectively. These alloys were produced from electrolytic grades of copper and zinc and a pure grade of straits tin, melted under borax in clay-graphite crucibles and cast in a vertical iron mold. Cylindrical pieces 1 in. in diam and 1 % in. long were machined from the casting and were faced by metallographic polishing to good matching end surfaces. Pairs of the cylindrical pieces were held

Jan 1, 1959

By Francis B. Foley

In examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found a piece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstattian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: Carbon Nickel Chromium Per Cent. Per Cent. PeR Cent. Metal from skin........................... 0.34 1.26 0.63 Widmannstattian zone.................... 0.21 1.18 0.63 Metal from center......................... 0.34 1.32 0.67 Such a condition might result from decarburization followed by recarburization of the skin. This section came from one of the branch runners to the bottom of the mold, not from the main runner, and it is difficult to conceive of decarburization occurring in this portion of a runner. If the metal were stripped while quite hot, some oxidation would take place but the recarburization is unaccounted for. It could not occur by segregation after solidification—the tendency then is for diffusion and homogeneity. The following seems to fit the conditions and is offered as an explanation. The outside layer of normal structure 0.065 in. (1.6 mm.) thick was chilled on the walls of the runner brick when the molten metal first entered the runner. As the molten metal flows by, the outside of the stream

Jan 1, 1920

By John Charles

The Engineering Method. By John Charles Lou11sbul.y Fish. Stanford University Press. 1950. 186 P. $3.-This book is about the "professional habit often referred to . . . . as 'the scientific method' . . ." It formulates for students the system of logic and reasoning that is the mark of the practicing engineer. The three chapters are, "The Method of Engineering", "Application of the Engineering Method" and "Uncertainties in Engineering." They cover logic and reasoning, terms, nontechnical problems, practical conditions controlling the engineering method, inescapable uncertainties and the method of coping with them. The author is emeritus professor of civil engineering at Stanford. The material presented here formed chapters 9, 10, and 11 of The Engineering Profession, by Hoover and Fish, second edition 1950. Elements of Ore Dressing. By Arthur F. Taggart. John Wiley & Sons, Inc., New York, 1950. $10.- A modern and practical introduction to the subject by the noted author of the Handbook of Mineral Dressing. The philosophy that a mill and all its parts comprise a single treatment process is a continuing theme in the book. Professor Taggart covers hand picking, screening, filtration, and electrical concentration. After introducing sedimentation, he takes up acceleration in free-settling, hindered-settling, sink-float, jigging, film and trough concentrators and shaking concentrators. A discussion of organic chemicals in flotation is followed by a detailed treatment of flotation. Final chapters deal with primary crushing, secondary crushing, grinding, transport, and controls and flowsheets.

Jan 3, 1951

By William E. Ford, Edward Salisbury Dana

5. Crystallography. - The subject of Crystallography includes the description of the characters of crystals in general; of the various forms of crystals and their division into classes and systems; of the methods of studying crystals, including the determination of the mathematical relations of their faces, and the measurement of the angles between them; finally, a description of compound or twin crystals, of irregularities in crystals, of crystal- line aggregates, and of pseudomorphous crystals. 6. Definition of a Crystal.- A crystal * is the regular polyhedral form, bounded by smooth surfaces, which is assumed by a chemical compound, under the action of its intermolecular forces, when passing, under suitable conditions, from the state of a liquid or gas to that of a solid. As expressed in the foregoing definition, a crystal is characterized, first, by its definite internal molecular structure, and, second, by its external form. A crystal is the normal form of a mineral species, as of all solid chemical com- pounds; but the conditions suitable for the formation of a crystal of ideal perfection in symmetry of form and smoothness of surface are never fully realized. Further, many species usually occur not in distinct crystals, but in massive form, and in some exceptional cases the definite molecular structure is absent. 7. Molecular Structure in General.- By definite molecular structure is meant the special arrangement which the physical units, called molecules, assume under the action of the forces exerted between them during the formation of the solid. Some remarks are given in a later article (p. 22 et seq.) in regard to the kinds of molecular arrangement theoretically possible, and their relation to the symmetry of the different systems and classes of crystals.

Jan 1, 1922

By H. M. Otte

Certain choices for the shear elements of the inhomogeneous distortion in the phenomenological theory of martensite formation are examined for their agreement with crystallographic and X-ray data of iron alloys. The assumption that the shear elements must represent slip or twinning systems characteristic of bcc metals is found to covey all observations, even when a small uniform dilatation is taken into consideration. In bct martensite, (011) becomes a possible twinning or faulting plane, in addition to {112), and qualitatively similar X-ray line broadening is to be expected from both. The basic concept inherent in the current theoriesl-4 of the formation of martensite is that the interface between the parent (austenitic) and product (martensitic) phase is an invariant strain plane (i.e., one that is undistorted and unrotated). Experimental evidence that the interface is of such a nature is available in certain transformations2'5'6 but for the transformation in iron alloys direct observation has not proved enlightening. Internal strains resulting from the formation of the small martensite platelets within the parent austenite matrix7 make it difficult to produce the desired evidence. Indirect evidence, however, such as the continuity of scratches in passing from untrans-formed to a transformed region, strongly indicates that the habit plane in iron alloys is an invariant strain interface. The scatter in habit planes in a given specimen8 would suggest that internal stresses have a slight but definite influence. On the other hand, composition changes which affect the lattice parameter can alter the habit plane appreciably, and by an amount greater than the scatter.' The success of the theories depends on the choice made for the "inhomogeneous distortion" or "complementary shear'' in the analysis and also on the choice for the parameter 6 representing a small uniform dilatation. In the approach developed by Wechsler, Lieberman, and Read'," it is implicitly assumed that 6 is unity. In the case of iron alloys, all observations cannot be explained without varying either the inhomogeneous distortion or 6 . Bowles and Mackenzie3 considered only the effect of varying d. They found it difficult to reconcile the wide scatter of habit planes with the theory and were forced to the conclusion that it may also be necessary to consider variations or different choices of the inhomogeneous distortion. Wechsler and Read" considered a limited number of possible choices for the inhomogeneous distortion, but no variation in 6, though this could easily have been introduced if so desired. It is the purpose of the

Jan 1, 1961

By C. S. Barrett, P. Coheur

ANNEALING twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the recrystallization texture,1 and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (111), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3,4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture this is true, for example, with the (113) [211] texture so commonly reported for brass-hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism . MATERIALS AND METHODS The samples investigated were of secondary copper (melted in Belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice has not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip 10 cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a cameral that traversed

Jan 1, 1946

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,' and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3'4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,' and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3'4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By B. Silliman

The experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phœnixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 21o F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so constructed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care-

By N. A. Gjostein

The real and apparent dependence of the surface self-diffusion coefficient, Ds, of gold on crystallo-graphic orientation has been investigated by isolated scratch smoothing and grain boundary grooving experiments. No systematic variation of Ds with orientation was found along the [100] zone. In view of the experimental scatter in these results, however, only aniso-tropy ratios, p, greater than -1.3 would be detectable. Anomalously low values of Ds were found on the [0ll] and [110] zones when the diffusion direction lies along (the scratch or grain boundary groove is perpendicular to) these zones. By comparing these results with a previous y plot study of gold, it is hypothesized that this is not an intrinsic diffusivity effect, but rather it results from a decreased driving force for mass transfer at orientations where the y-plot curvature is negative and appreciable in magnitude relative to y. The characteristics of this type of anisotropy do not appear sEVERAL investigations1-7 have dealt with the anisotropy of the surface self-diffusion coefficient, Ds, of metals as measured by the decay of single or multiple to be in agreement with the hypothesis of fast diffusion along ledges in the surface structure. In certain cases the Fourier method of determining Ds, described in Paper I of this series9 was compared with the second moment analysis in order to determine whether or not the method of analysis affects the anisotropy ratio. While the type of analysis does influence the magnitude of the anisotropy ratio, this effect is not associated with the shape of the profile, but rather is connected with the iterative volume diffusion correction used in conjunction with the second moment analysis. It is further demonstrated that the volume diffusion correction can be too large by either method when the y-plot curvature effect is large. Certain orientations exhibit an unusual temperature dependence of Ds ; this is discussed in terms of the y-plot curvature effect and/or the influence of impurities on Ds . scratches in the surface. Depending on the system investigated, both large1"3'6'7 and small4'5 anisotropies in Ds have been found. Although adsorbed impurities undoubtedly play an important role in determining the magnitude of the anisotropy,8 there are other factors that can give rise to an apparent anisotropy in Ds, thus obscuring the true nature of an intrinsic anisotropy in

Jan 1, 1968

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,' the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*' specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By N. M. Parikh, T. J. Koppenaal

The strengthening mechanism of fiber-reinforced silver has been investigated as a function of fiber density and fiber material. Stress-strain curves were determined in the range 2 x 10-6 to 2 x 10-3 plastic styain and slip lines were examined. The yield strength at 0.2 pct permanent strain is markedly dependent upon fiber density but the stress necessary to initiate plastic deformation is independent of fiber density. The strengthening mechanism of the fibers is shown to be malogous to grain boundary strengthening in poly crystalline metals. The variation in strengthening with different types of fibers is also noted and discussed. In recent years, considerable progress has been made in the understanding of the mechanical properties of two-phase systems, particularly in the classical dispersed-phase alloys where the separation between the dispersed phases is 0.01-0.1µ. However, little work has been done on fiber-reinforced metals where the dispersed-phase separation is considerably larger than this. Parikh1 investigated the mechanical properties of many fiber-reinforced metals and found that two general relationships are always observed, as follows: 1) A fibrous network incorporated into a second weaker metal strengthens the latter, and the amount of strengthening increases with fiber concentration. 2) At a corrstant fiber concentration, the amount of strengthening in a given matrix can vary considerably, depending upon the type of fiber employed. The object of the present investigation was to examine the fuiidamental factors controlling these two observations. procedure: Fig. 1 shows the initial step in the fabrication of the specimens. The sieve is shaken so that the fibers fall into a mold with the longitudinal axes of most fibers in the X-Z plane. The fibers are then compressed to a predetermined density, thus forming a "felt", and the necessary amount of matrix metal is added to the top of the felt. The mold is heated, in vacuum or hydrogen, to above the melting point of the matrix metal; the molten metal flows into the felt, and the entire assembly is cooled. This produces a "composite" that is essentially free of voids. A number of composites were prepared in this manner using 1/4-in. kinked lengths of mild steel

Jan 1, 1962

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943