Search Documents

By S. E. Haszko

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuA12 and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band. 1,4 Europium in EuAl2, appears to have a valence closer to 2. In previous work.' X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref 1. One of the other phases was identified as Co,Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. 'J. H. Wernick and S. Geller: AIME Trans., in press. 'J. H. Wernick and S. E. Haszko: to be published. 'F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. 'S. E. Haszko: to be published. 'J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acla Cryst., 1959, vol. 12, p. '162. The Influence of Hydrogen on the Lattice Parameters of Ti-Sn Alloys A. Coucoulas and H. Margolin A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently higher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By G. Howell Clevenger

FORMERLY great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,1 Breuil,2 Wigham,3 Burgess and Aston,4 Ball and Wingham,5 Miiller,6 Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil 9 and Stead.10 Stead 11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness " to the presence of small amounts of copper. Turner 12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 10, 1913

R. Schuhmann, Jr. (Purdue University)— Fulton and Chipman's results on rate of silica reduction from slags are analogous in many was to the results of Parlee, Seagle, and Schuhmann10 on rate of alumina reduction from alumina crucibles. Both investigations have given comparably low rates of reduction and slow approaches to equilibrium. Accordingly, we may hypothesize that the rate-determining step is the same in both kinds of experiments; that is, oxygen diffusion across the stagnant boundary layer on the liquid-metal side of the interface between the liquid metal and the oxide phase (slag or solid oxide). I suggest that silica reduction involves the following consecutive steps: I) At the slag-metal interface: SiO2(slag) Si+ 20 II) Transport of oxygen from slag-metal to gas-metal interface: a) diffusion across liquid-metal boundary layer at slag-metal interface. b) convection within the body of liquid metal. c) diffusion across boundary layer at metal-gas interface. 111) At the metal-gas interface: C +O- CO (gas) Iv) At the graphite-metal interface: C (graphite) -C At steelmaking temperatures it is reasonable to assume that equilibrium is attained in all three chemical reactions (I, 111, and IV) right at the respective interfaces. Convection within the stirred liquid metal (step IIb) is also rapid. Transport of Si and C should be orders of magnitude easier than transport of 0, because of the relatively high concentrations of Si and C. Accordingly, we might expect the overall reaction rate to be determined by boundary-layer diffusion of oxygen, either IIa or IIc. Fulton and Chipman's demonstration that bubbling CO through the system had no major effect on reaction rate indicates that IIc is not the slowest step. Therefore, it becomes logical to estimate the maximum rate for step IIa and to compare this theoretical estimate with Fulton and Chipman's experimental data. If oxygen diffusion across the liquid metal boundary layer at the slag metal interface (step IIa) is rate-determining, In this equation, dn sio, /dt is the rate of silica reduction in moles per sec,A is the area of slag-metal interface in sq cm, Do is the diffusivity of oxygen in sq cm per sec, 6, is the boundary layer thickness in cm, c,* is the oxygen concentration right at the slag-metal interface in moles per cubic cm, and co is the oxygen concentration in the body of the liquid metal, also in moles per cubic cm. Equilibrium data" on the silicon deoxidation reaction in liquid iron and steel at 1600°C indicate that the oxygen contents of the liquid metal in Fulton and Chipman's experiments at 1600°C probably fell in the range of 0.5 x10-3 x10-3wt pct. That is, the maximum conceivable value of co*-co for the system under consideration was on the order of 10"5 mole oxygen per cubic cm. On the basis of previously published data,1O,11 it is estimated that Do/0 will fall somewhere in the range from 10-3 to 10-1 cm per sec. The surface area A in Fulton and Chipman's experiments was approximately 20 sq cm, and the weight of metal involved was about 500 grams. Combination of all these figures with the above rate equation leads to an estimate that the rate of silica reduction should fall within the range from 0.002 to 0.2 wt pct Si per hr. This estimate is consistent with the experimental data. For example, Fulton and Chipman's Fig. 2 shows a change of about 0.3 pct Si in 10 hr, corresponding to an average rate of 0.03 pct per hr. According to the proposed hypothesis, increasing the temperature will increase the reaction rate ill two ways: 1) by increasing oxygen diffusivity and 2) by increasing the oxygen concentration (oxygen solubility) in the liquid metal. The combination of these two effects accounts for the high value of the observed activation energy. Summarizing, I propose that the rate of silica reduction, like that of the carbon-oxygen reaction, is diffusion controlled and that low oxygen concentration in the liquid metal is the major factor accounting for the very low observed rates of silica reduction. John Chipman (author's reply)—The authors thank Professor Schuhmann for his interesting contribution. His proposed explanation may well prove to be the correct one. There is clearly a need for much further experimental work on this problem, and further research is in progress.

Jan 1, 1961

By K. R. Garr, D. Kramer, A. G. Pard

EXPOSURE of steels to a fast-neutron flux results in helium generation by (n,a) reactions. The elements Fe, Ni, Cr, and N are major participants in the (n,a) reaction and helium concentrations of up to 5 x 10"5 atom fraction could accrue in fuel clads after a year of service in proposed fast reactors.' Such concentrations of helium can severely reduce the ductility of alloys at temperatures of reactor service. The phenomenon of helium embrittlement has been studied in austenitic alloys which were irradiated with particles as a rapid means of producing significant helium concentrations.2-5 The pres-ent work is a continuation of those studies and is concerned with helium effects in a ferritic stainless steel. I) EXPERIMENT Small sheet tensile samples with a gage length of 0.50 in. and a cross-section of 0.009 by 0.040 in. in the gage length were punched from cold-rolled type 405 stainless steel. The composition of the steel used in this work is given in Table I. Prior to helium injection, the samples were annealed 24 hr at 760°C which caused complete recrys-tallization with a resulting grain size of 40 u. This treatment rendered the alloy completely ferritic and carbide particles, 0.5 to 2 uin size, were present at a density of 1 x 1011 cm-3, Fig. 1. These carbide particles were probably a mixture of the M7C3 and M4C types.6 Helium was injected into the samples by irradiation with a particles from a cyclotron, which produced uniform concentrations through the center two-thirds of the sample thickness. Details of this procedure were previously described.' The average helium concentration, as measured on a gas-source mass spec- 11) RESULTS A) Tensile Tests. The results of the tensile tests are given in Table I1 where the values shown are averages of two samples. There was no significant effect of helium on either the yield strength or tensile strength at 550" or 650°C but an increase in both is apparent at 750°C. Samples with helium showed a 20 pct loss in total elongation at 650°C which increased to a 55 pct loss at 750°C. The uniform elongation is not affected by helium at 550" or 650°C but shows an increase at 750°C.

Jan 1, 1970

EXPLORATION U.S. 4,065,972 - Exploration for subsurface ore bodies of uranium. mercury or other inorganic or organic minerals having specific gases associated thereto Small gas sample containers are planted in a plurality of shallow holes in the surface of the earth in a predetermined pattern and left in place for a period of time sufficient to collect migrating gases. Each container includes a gas collection chamber and means for admitting gases at a predetermined flow rate. Strips of detector material which is sensitive to specific gases are mounted in the collection chamber. Recovered containers are subjected to qualitative and quantitative analysis. F. W Holub and H. W. Alter, assigned to Terradex Corp Jan. 3, 1978. 9 pp (73-421 5R) Filed 5-24-76 (689,710) Same. British 1,498,737, dated Jan. 25, 1978

Jan 1, 1979

By Paul A. Beck, M. N. Parthasarathi

The vecrystallization texture. formed by selective growth of random nuclei in an 80 pct volled 99.997 pct A1 crystal of initial orientation mear (123) (41.21 was found to consist of components related to the single-component rolling texture by 40 deg. rota-tiows around [111]axes. The relative-volume fractiovz of the various recrystallization-texture componezts may be accouzted for 012 the basis of the Lou) mobility of twist boundaries, if it is assumed that the mobility of the tilt boundaries also varies with their orientation. Similar results with a, aluminum-alloy cystal of the (110) [112] orientation, containing iron, silicon, and zinc, show that these solute contents do not impair the effectivezess of the oriented growth mechanism of re cry s-tallization- texture formation. In a previous investigation1,2 it was found that a sharp recrystallization texture is formed as a result of the oriented growth of random artificial nuclei in an aluminum crystal rolled to 80 pct RA, on the (110) plane in the [ 112] direction. Four recrystallization-texture components were found to occur, with orientations corresponding to 40-deg rotations around [111 1 axes of the deformation texture. Reorientations of this type were already found in earlier work,3,4 where the presence of random nuclei could be reasonably assumed, but was not rigorously documented. The same orientation relationship was found also by Lucke and Liebmann, who actually measured the orientation dependence of boundary-migration rates in the recrystallization of A1 crystals slightly deformed in tension.5,6 The occurrence in the recrystallization texture of only four of the eight crystallographically equivalent orientations of the type referred to above remained unexplained,1,2 although it was clearly not a result of the absence of suitable nuclei. Recently Burgers7 suggested that this effect may be due to the aniso-tropy of boundary mobility observed2'6; it was found that the recrystallized grains of the 40-deg [111]-rotated type grow much faster in directions perpendicular to the [ 111] they have in common with the matrix than parallel to this direction, i.e., the tilt boundaries have much higher mobility than the twist boundaries. The four orientations corresponding to

Jan 1, 1962

By W. C. Ellis, E. S. Greiner, M. E. Fine

C. H. Samans and W. R. Ham (Chicago, Ill., and Dix-field, Maine, respectively)-—For several years we have been studying transitions of this basic type in metals, alloys, glasses, etc. Usually, however, they are not so clearly marked as those which the authors have found, and hence are much more difficult to determine accurately. Since our studies indicate that most of them occur virtually unchanged (as far as temperature is concerned) regardless of the form in which the element appears, we believe that they are a characteristic of the atom. Specifically, we believe that there is an additional rotational degree of freedom possessed by the nucleus which has not been considered heretofore. This nuclear rotation is made up of several components, each related to the several quantum shells of electrons. In chromium there are four of these shells and hence four separate series of characteristic transition temperatures. The lowest temperature at which any transition occurs, based on the present state of our computations, is 125°K, 4° higher than the authors' value of 121°K. A convergence of this series, we believe, shows up at the higher temperature of 2085 °K, surprisingly close to the transformation temperature of 2103°K recently announced by N. J. Grant of M.I.T. for a body-centered to face-centered transformation in chromium. Likewise, our computations indicate a temperature of 311°K for the second transition temperature, reported by the authors as 310 °K. A convergence of this series, we believe, shows up at a higher temperature as the melting point at 2163°K. Although our work on these series must, in a sense, still be regarded as empirical, since we do not understand fully as yet just what the series mean, it is based on a reasonably firm picture. The individual constants, from which the various series are computed for each element, comes directly from the X-ray K absorption limit. Furthermore, the same basic method has accounted for transformation and melting temperatures in about 50 of the chemical elements, which is all we have tried thus far. In many cases the only known transformation is the melting point, but in others the occurrence of transformations or other transitions, equally as well marked as those of the authors, has been pointed out by others. These observations have assisted us greatly. Consequently we were very pleased to see the authors' excellent work in finding these two transitions in chromium. With these confirming data, our picture of this element is clarified considerably, so we expect that at least some of our work can be published in the near future. R. C. Ruder (E. I. du Pont de Nemours & Cu., Wilmington, Del.)—The authors' interpretation of these transitions in terms of 3d to 4s electronic structure transitions is most interesting. It would be interesting to have additional experimental evidence of such transitions from the temperature dependence of the Hall coefficient in the neighborhood of the property changes discussed in this paper. Simple theory15 suggests the Hall coefficient as a measure of the free electron (or s electron) concentration per unit volume. It has been shown that for paramagnetic'" and ferromagnetic1? metals the simple theory is in fact too simple. However, the existence of a discontinuity in the Hall coefficient would provide information which should aid both in our understanding of these transitions and the significance of the Hall coefficient in these metals. It was rather surprising that no significant paramagnetic effects were observed. In this connection the recent work of McGuire and Kriessman18 is cited. They measured the magnetic susceptibility of chromium from 20" to 1460 °C. They also observed no large change in the susceptibility although there might be a change in slope in the vicinity of the 40 °C transition. The existence of these 3d to 4s electronic transitions has been discussed in connection with the paramagnetic susceptibility behavior of nickel and nickel alloys.'"-" Assuming a correspondence principle between classical and quantum mechanical paramagnetic theory and using classical theory to calculate the effective Bohr magneton number from the Curie constant for substances obeying the Curie-Weiss law," it is found that the effective magneton number is a function of temperature. The process of calculation involves the inverse of the differential of the 1/x4 vs. temperature curve so that good and numerous data are necessary to obtain significant results. The data of Fallot23 show a discontinuous increase of about 12 pct in the effective magneton number between 850" and 900 oC, followed by a continuous increase up to the melting point. The data of Sucksmith and Pearce24 show a possible 8 pct increase. The older data of Terry25 and Weiss and Foex26 show a continuous increase. It is possible that small amounts of impurity atoms change these electronic transitions significantly. Fallot's23 data on a nickel alloy with 4.5 atomic pct Fe indicate that the discontinuity occurs around 1300 °C. Systematic investigation of the transition metals for transitions of this nature should provide information which would be very valuable for our understanding of these metals. The absence of antiferromagnetic structures in chromium has been shown by Shull27 using neutron diffraction techniques. M. E. Fine, E. S. Greiner, and W. C. Ellis (authors' reply)—The remarks by Drs. Samans and Ham are certainly very interesting, in particular those pertaining to the close agreement between the theoretically calculated values for transition temperatures in chromium and the experimental values reported by a number of investigators. This is a remarkable achievement and we shall look forward to a more detailed presentation of the method followed in their calculations. We do not believe that the transition in pure chromium near 40 °C remains temperature invariant with alloying, as was reported by Samans and Ham for a number of the substances that they studied. We have not done any work with alloys but base our belief on the results of earlier studies in which less pure chromium was included and considerably lower transition temperatures were observed. The transition tempera-

Jan 1, 1952

By GILBERT C. DAVIS

ANY thought of Morenci naturally includes its sister town of Clifton, its gateway to the outside world. Clifton, the country seat of Greenlee County, is the terminus of a branch line of the Southern Pacific railroad from Lordsburg, N.M. Carload freight incident to the Morenci operation moves from Clifton over Phelps Dodge?s standard-gauge industrial railroad. Private freight must be hauled by truck. These two communities fell far short of supplying adequate housing for the personnel concerned with the new operations so a new townsite, Stargo, was developed adjacent to Morenci. Here 234 housing units with garages have been built and twenty similar units have been erected near the reduction works.

Jan 1, 1942

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By R. W. Raymond

The various modifications of the art of photography have become within the last few years the indispensable allies of every art and science. But, before the introduction of the process which is the subject of this paper, there was, so far as I am aware, no satisfactory means by which certain photographic negatives could be made to yield, without the intervention of the skilled draughtsman, electrotypes suitable for surface-printing. I refer to negatives taken from originals, such as natural objects, or or lithographs, in which the lights and shadows are not represented exclusively by lines and dots, such as can be photo-engraved. The greater usefulness to engineers and manufacturers of electrotypes as compared with lithographs is evident. The electrotypes can be kept indefinitely and used in the production of many thousand copies. They can be duplicated at trifling cost. They can be placed for printing together with the " forms " of type, or included in these, upon an ordinary press. Finally, they are cheap, when made mechanically from a suitable original. Various methods have been adopted for the preparation of such a secondary original (as it might be called) in cases where the first original is unsuitable for photo-engraving. Thus, for instance, portraits have been produced in electrotype from ordinary photographs as follows: A large negative is made of the original (say a carle de visite of a person deceased), and a proof taken, but not " fixed." Over this proof a skilled artist draws the portrait with a pen, producing a picture which resembles a line-engraving. The photographic proof, which has served merely to guide the artist, is now obliterated, and the pen-and-ink drawing is photo-engraved. Electrotypes thus produced often retain the likeness in a wonderful degree, and give spirited and satisfactory pictures. 1 may instance, as examples, which many will recollect, the portraits of our deceased members,

Jan 1, 1887

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,&apos; and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon&apos;s data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

The President was authorized to appoint. a liaison committee to cooperate with the American Mining Congress in respect to the establishment of a Secretary of Mines and Mining in the President&apos;s Cabinet. He appointed Edwin Ludlow, Chairman; Mark L. Requa, and J. E. Johnson, Jr. It was resolved to accept the invitation from the Chicago Section to hold the. 120th meeting of the Institute in Chicago during the week of Sept. 15, 1919. The action of the Executive Committee in appointing Past President E. Gybbon Spilsbury as representative of this Institute to visit France upon the invitation of the Société des Ingénieurs Civils de France was approved. The final budget for 1918 was approved. Tile President was authorized to appoint a committee, of three members, on the Development of Activities of the Institute. The committee was requested to report at the February meeting of the Institute, and the Secretary was requested to invite each local section to have a member present to discuss the subject. The President appointed J. W. Richards, Chairman; P. N. Moore, and Allen H. Rogers. Thirty-six members, ten associates, and five junior associates were elected; one change of status from associate to member was granted; two members were reinstated; and eight resignations were accepted. An extension of time was granted to nine members. The dues of eight members were suspended on account of their being in active service.

Jan 2, 1919

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent&apos;s office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day&apos;s pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent&apos;s office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day&apos;s pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

By Benjamin C. Craft

Oil and gas development in Louisiana during 1935 brought this state at the close of the year up to fourth place in the nation as a producing area. A review of development in North Louisiana centers around Rodessa, the most important reserve discovered in this area in many years. While the producing limits have not been defined, this discovery is one of the major developments of the year. New gas fields were discovered in Lincoln, De Soto and Bossier parishes. The Lincoln Parish discovery, completed flowing a highly saturated gas from the Glen Rose, further indicates the importance of deep-seated prospects in the interior salt-dome area. Minor extensions were made at Sligo and Pine Island. During the year, 126 oil wells and 103 gas wells were completed in North Louisiana as compared with 144 oil wells and 68 gas wells during 1934. The North Louisiana oil production was 9,617,405 bbl. as com-pared with 9,274,050 bbl. during 1934, an increase of 343,355 bbl., while the gas production increased 18 billion cu. ft. in 1935 over its 1934 figure. The Louisiana Department of Conservation gage of Nov. 1, 1935, shows an open-flow capacity of 4,563,725,000 cu. ft. per day from 941 wells in the Monroe field and 682,770,000 cu. ft. from 159 wells in the Rich-land field. A great deal of leasing continues in North Louisiana as a result of the Lincoln Parish discovery and development in the Rodessa field, especially in Bossier, De Soto, Winn, Lincoln, Bienville, Webster, Ouachita and Richland parishes. South Louisiana&apos;s position as an area of important reserves was further proved during the past year. Increased drilling resulted in the discovery of seven new fields: Lafitte, Garden Island Bay, Tepetate, Bunkie, St. Martinsville, Jeanerette and Big Lake. New sands or producing horizons proved productive in 15 of the proven fields. The total oil production for South Louisiana during 1935 was 40,731,-056 bbl. as compared with 23,255,437 bbl. during 1934. There were 222 oil and gas wells completed in South Louisiana during 1935 as compared with 214 oil wells during the previous period. Drilling during

Jan 1, 1936

By Benjamin C. Craft

Oil and gas development in Louisiana during 1935 brought this state at the close of the year up to fourth place in the nation as a producing area. A review of development in North Louisiana centers around Rodessa, the most important reserve discovered in this area in many years. While the producing limits have not been defined, this discovery is one of the major developments of the year. New gas fields were discovered in Lincoln, De Soto and Bossier parishes. The Lincoln Parish discovery, completed flowing a highly saturated gas from the Glen Rose, further indicates the importance of deep-seated prospects in the interior salt-dome area. Minor extensions were made at Sligo and Pine Island. During the year, 126 oil wells and 103 gas wells were completed in North Louisiana as compared with 144 oil wells and 68 gas wells during 1934. The North Louisiana oil production was 9,617,405 bbl. as com-pared with 9,274,050 bbl. during 1934, an increase of 343,355 bbl., while the gas production increased 18 billion cu. ft. in 1935 over its 1934 figure. The Louisiana Department of Conservation gage of Nov. 1, 1935, shows an open-flow capacity of 4,563,725,000 cu. ft. per day from 941 wells in the Monroe field and 682,770,000 cu. ft. from 159 wells in the Rich-land field. A great deal of leasing continues in North Louisiana as a result of the Lincoln Parish discovery and development in the Rodessa field, especially in Bossier, De Soto, Winn, Lincoln, Bienville, Webster, Ouachita and Richland parishes. South Louisiana&apos;s position as an area of important reserves was further proved during the past year. Increased drilling resulted in the discovery of seven new fields: Lafitte, Garden Island Bay, Tepetate, Bunkie, St. Martinsville, Jeanerette and Big Lake. New sands or producing horizons proved productive in 15 of the proven fields. The total oil production for South Louisiana during 1935 was 40,731,-056 bbl. as compared with 23,255,437 bbl. during 1934. There were 222 oil and gas wells completed in South Louisiana during 1935 as compared with 214 oil wells during the previous period. Drilling during

Jan 1, 1936

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at temperatures from 0 to approximately 1030&apos; C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825" C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some additional data which will subsequently be described. Materials and Methods The alloys used in this investigation are listed in Table 1. They were prepared in 30 or 50-gram ingots by melting specially purified silicon and electrolytic or carbonyl iron in alundum crucibles under a pressure of less than 1 mm. of mercury. The purity of the silicon, electrolytic and carbonyl irons has been given by the authors in previous publications2, 5. The ingots were homogenized in vacuo at approximately 1000" C. for at least 96 hr. and then slowly cooled. The homogenized specimens were ground to powder in a hardened steel mortar. This powder was passed through a 150 or 200-mesh screen and sealed in evacuated quartz, Jena or Pyrex glass tubes and heat-treated as noted in the various tables. Specimens 23A, 24B, 33 and 35 and the specimens heated for one month at 700" C. were quenched by quickly removing the tubes from a horizontal tubular furnace and dropping them into water. The other specimens were quenched by means of a drop-quenching device, which has been described previously3.

Jan 1, 1937

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa&apos;s Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect&apos; and by Chapman in a report on the San Manuel Copper Deposit.&apos; The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect&apos; and by Chapman in a report on the San Manuel Copper Deposit.&apos; The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953