Search Documents

By F. C. Wagner, E. P. Klier, D. E. Nulk

The presence or absence of plastic strain at a cleavarage surface is a question of much importance, and upon its answer depends future possible theoretical work. To investigate this question back-reflectinn X ray patterns were obained on the cleavage facets of ferrite grains. The test set-up consisting of FeK colli- mated radiation, single grain material and stationary cassette and specimen will not lead to a diffraction pattern, in general, but is an ideal arrangement for the exami-nation of surface effects. A pattern taken on hydrogen purified

Jan 1, 1949

By A. M. Gaudin

THE purpose of ore dressing is to separate the rough ore into one or several valuable concentrates and a discarded tailing. The first step is to crush the ore so that the resulting particles may be individually valuable or worthless. The next step generally has to be a sizing operation, because the property by which concentration is effected depends on the size of the in-dividual mineral particles as well as on their physical properties. These two effects may cancel each other if a preliminary sizing is not resorted to. Sizing is accomplished by screening or classifying. Screening depends almost solely on the dimensions of the particles; classifying depends also on the specific gravity of the particles and the viscosity of the settling medium in which the classifying operation is conducted. Classification, therefore, is to a certain extent a con-centrating operation as well as a sizing operation. Before the days of concentration by flotation, the available screens were mechanically poor. As a result classification was employed for sizing in the range. of comparatively coarse sands (table feeds). In recent years, the advent of stage-grinding to flotation size has brought about the development of good screens, which are more economical than classifiers down to about 20, -mesh. With decreasing size at which separation is to be made, screens become increasingly uneconomical, while classifiers become increasingly economical. The line of demarcation between the respective fields of screening .and classification is, therefore, fairly sharp. With the development of processes of concentrating finely comminuted ore, the need for classifiers or other sizing devices operating so as to make efficiently a split at a very fine size has become increasingly apparent. Such classifiers might be termed de-slimers, from the fact that they separate a material having a slimy ap-pearance from one having the characteristics of a sand. Sizing-tests are carried on by means of testing sieves, the finest of which have apertures of about 1/500 of an inch. The 200-mesh sieve, which has an average open-ing of 0.0029 linear inches is generally considered the limit of practical test-sizing. As a result, little is known of minus 200-mesh material and the advantages of classifying concentrator feeds within the minus 200-mesh range has been overlooked. An extension of the -present sieve scale beyond the 200-mesh screen is given in Table 1.

Jan 2, 1927

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

Jan 1, 1963

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By F. Weinberg, L. MacAulay

DAVIS,&apos; in an investigation of solute redistribution along molten rods of dilute silver in tin, concluded that at horizontal temperature gradients below approximately 5°C per cm very little convective mixing takes place. Cole and winegard2 observed temperature oscillations in horizontal melts of tin, with temperature gradients of several deg per cm. They associated the temperature oscillations with the presence of convective flow in the melt. At temperature gradients less than 1°C per cm they did not detect convective flow. In the present work, direct measurements of con-vective flow in liquid tin have been made using a radioactive tracer technique. The results indicate that extensive convective flow occurs at temperature gradients below those previously reported. The apparatus used to determine the extent of con-vective flow is shown in Fig. 1. The graphite boat Fig. l(a), has two rectangular channels both of which contain molten tin. Radioactive Ag110 in the form of Sn-0.2 pct Ag alloy was introduced at the end of one channel, by rotating the cylinder shown. A series of fixed thermocouples were positioned along the center of the second channel to determine the temperature gradient. It was assumed that the two channels had identical temperature distributions. The graphite boat was inserted into a vycor tube which was surrounded by a multiple winding tube furnace as shown in Fig. l(b). The tin was melted in an argon atmosphere. The distribution of Ag110, as a function of position along the boat at a given time after introduction of the ~g"&apos;, was determined with the

Jan 1, 1970

Executive SCOTT TURNER, Chairman FREDERICK M. BECKET JOHN A. MATHEWS H. A. GUESS WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL D. MERICA ROBERT E. TALLY Admissions JOHN M. LovEJOY, Chairman GEORGE D. BARRON ERLE V. DAVELER WILLIAM H. BASSETT W. D. B. MOTTER, JR. Alternates HENRY B. FERNALD F. JULIUS Polls AMOR F. KEENE

Jan 1, 1932

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl&apos; who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By H. L. Riley, B. W. Gandrud

A froth flotation unit was added to the DeBardeleben Coal Corporation&apos;s Empire washer at Empire, Alabama, in the fall Of I94O following an investigation of possible ways and means of recovering coal values from settling-tank overflow or slurry. Officials of the DeBardeleben corporation hoped that some practical and reasonably economical way could be found for recovering fine coal from overflow water, although there had as yet been very little progress along this line in the Alabama coal fields. The Bureau of Mines was asked to cooperate in the project through its Southern Experiment Station, at University, Alabama. This paper presents a brief description of the process and the installation that resulted from the investigation of the overflow water or slurry problem at the Empire mine. The experimental data include&apos; as a Part of this Paper were obtained during the course of the investigation in 1940 Since that time, however, the flotation unit has been running more or less continuously without significant operational changes and is still Performing pretty much in accordance with the data obtained in 1940. Flowsheet at Empire and Type of Coal Treated The Empire mine is developed on the Black Creek bed near the the border of the Warrior field. The coal in this bed is extremely low-ash and although there is an almost complete absence of bone coal and partings, the bed is so thin that, with mechanized mining, a high percentage of rock from roof and floor inevitably gets into the run-of-mine coal. The thickness of the Black Creek bed throughout the part of the Warrior field in which it is mined extensively is rarely over 30 in. and probably would average about 25 in, the coal is of the high-volatile A rank and of excellent quality, but as a result of admixture of roof and floor material, the run-of-mine product usually contains I ; to 20 pct rock by weight. he following is a proximate analysis on an "as-received " basis of a typical seam sample from the Empire mine:&apos; moisture, 3.0 pet; volatile, 34.6 fixed carbon 58.3; ash, 4.1 This sample shelved 15,070 Btu per pound and 0.9 pct sulphur on a moisture-and-ash-free basis. In the Empire preparation plant the lump sizes above 3 in. are removed and hand-picked on a Marcus conveying Screen, the 3 to ? -in. size is removed by vibrating screens and washed in two Montgomery single-cell jigs, and the ?-in. to o slack is cleaned on four diagonal

Jan 1, 1949

Jan 1, 1967

By G. Reinberg, C. D. Clarke

Most underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating costs, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions.

Aug 1, 1956

Aamot, Olav Crone, (M&apos;29) Chem. Engr., Elektro¬kcmisk, Raadhusgt. 32, Oslo. Norway. . Aase. Glenn D., (J&apos;40) Jr. Met., American Smelt. & Refin. Co., Selby, Calif. Abadie, Henry G., (J&apos;43) Petr. Engrg., Avenal, Calif. Abadilla, Quirico A., (M&apos;38) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin Townsend, (J&apos;40) Jr. Engr., Phelps Dodge Corp., Morenci Branch. Morenci. Ariz. Abbott, Clarence E., (M&apos;04) Civ. Engr. V.P., Tennessee Coal Iron & R.R. Co., 1542. Brown Mars Bldg. Birmingham. Ala. Abel, Raymond L.. (M&apos;23) Chem. Engr., Com¬manding Officer, Pittsburgh Chem. Warfare urement Dist., American Bank Bldg.. Pittsburgh. Pa. Abel, Walter D., (M&apos;32) Min. Engr., Supvr. Engr.. R.F.C., Los Angeles, Calif. Abele, Louis T., (M&apos;31) 423 3rd Ave., Decatur. Ga. Abell, Leo M.: (M&apos;31) Mill Supt. & Met.. Em¬ peror Gold Min. Co., Ltd., Vatukoula. Fiji Islands. Abernathy, G. E., (M&apos;38) Geol., Kansas State Geol. Survey, Pittsburg, Fan. Abernathy, Jack H., (M&apos;40) Cons. Petr. Engr., First National Bldg.. Oklahoma City, Okla.

Jan 1, 1943

By Jei Y. Choi, Paul G. Shewmon

The surface self-diffusion coefficient of copper (D,) has been measured between 847° and 1069 "C for six different orientations. These were the(111), (110, (100, and three higher index surfaces. The activation energy for Ds (designated Q s) was found to be about 49 kcal per mol for all six surfaces, and Do about 2 x 104 sq cm per sec. At any temperature Ds varied by no more than a factor of three over these orientations. It is shown that, if the free energy of a surface atom is uniquely determined by its number of nearest neighbors, it follows from the Principle of microscopic reversibility that Qs should have the same value for all surface orientations, and Ds should vary little with orientation. This model also suggests that for clean fee metals Qs ~ 2/3 AH, (heat of vaporization). This is true for copper. ALTHOUGH it has been appreciated for several decades that atoms can diffuse more rapidly on a surface than through the bulk of a crystal, it has only been in the last few years that reliable values of the surface self-diffusion coefficient (Ds) have become available. Tracer studies of Ds had been attempted prior to this period, but when a tracer is placed on a surface, an ever increasing fraction of it is drained off into the lattice. The correction for this loss involves a very difficult, and as yet unperformed calculation. Those who have worked with tracers have not corrected for this loss.1, 2 Thus their results indicate that Ds is greater than the self-diffusion coefficient in the lattice (Dl), but it has not been established that they give quantitative data on Ds. A procedure which avoids the problem of tracer loss is to study the rate of mass-transfer under the effect of surface tension. If the surface asperity being studied is very small, the mass transfer occurs entirely by surface diffusion. The kinetics at which a grain boundary groove forms on an initially plane surface is a well-studied case of this type. The smoothing of a slight scratch in an otherwise flat surface is another procedure that has been studied. If these grooves are up to 20 to 30 µ in width, the dominant mechanism for mass transfer is surface diffusion (at least in the case of metals with low vapor pressures), and the widths can easily be measured with an interference microscope. Of these two, mass-transfer techniques only in the case of grain boundary grooving has a rigorous mathematical treatment been given. This was done by Mullins.3,4 His analysis predicted that in the case of copper in an atmosphere of an inert gas, surface diffusion should be the dominant transport mechanism. This analysis gave an equation for the groove profile and predicted that the width of the groove would increase as (time)1/4. Mullins and Shewmon showed that both of these predictions agreed with experiments.5 Thus the validity of the values of Ds given by this procedure seems to be well established. Gjostein has used copper bicrystals and the grain boundary grooving technique to determine Ds and the activation energy for surface selfdiffusion (9,) in the [001] direction on surfaces ranging between the (100) and (110) planes.= He reported that Qs = 41 kcal per mole and Do = 6.5 x 102 sq cm per sec for all orientations studied. Since the results did not change with the dew-point of the dry hydrogen atmosphere or the type of refractory tube used, he concluded that the surfaces were clean, or at least that the results were not influenced by any impurities chemisorbed from the atmosphere. The work reported here reproduces and extends Gjostein&apos;s study in that D s and Q s were determined for copper over a wider range of orientations. To study the effects of impurities, two purities of copper were used as well as cathodic etching to remove any possible electropolishing film. Gjostein postulated that the diffusing atoms on a surface near a low index plane are the few atoms which are adsorbed on the smooth region between ledges or steps in the surface. A more rigorous derivation of the equation relating Ds to the concentration and jump frequency of these adsorbed atoms is given here. Using this treatment, our empirical observation that Q s and D s are essentially the same for all surface orientations can be shown to follow from the assumption that the free energy of a surface atom is uniquely determined by its number of nearest neighbors. The studies of D s using the scratch technique have been carried out by Blakely and Mukura on nickel,&apos; and by Geguzin and Oveharenko on copper. The latter study using copper gives values of D s roughly

Jan 1, 1962

Jan 1, 1968

By C. W. Spencer, J. T. Smith

GRAIN-BOUNDARY surfaces are penetrated by a liquid phase when the liquid-solid interfacial tension is less than one-half the tension of the grain-boundary surfaces. Grain growth may occur in the presence of this liquid phase. burke1 reports that grain growth of this nature has been observed in two-phase ceramic systems. He suggests that the presence of a grain-boundary liquid may accelerate or decelerate the

Jan 1, 1963

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation&apos;s mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation&apos;s mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation&apos;s mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By Y. C. Liu, G. A. Alers

The anisotropy of Young&apos;s modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,&apos; the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.&apos;" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling&apos;s work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman&apos;s experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman&apos;s plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916