Search Documents

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1' shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter's' original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By Thomas T., Read

THROUGHOUT the Colonial era, Philadelphia was easily , the leading city of North America, and it still held that position at the end of the period, with a population of about 25,000, though closely pressed by Boston, which had slightly over 20,000, and New York, which had nearly as many. It was the center of a region in which mineral industry was important. Thomas Rutter's bloomery, built in the Schuylkill valley in 1716, was quickly followed by many others, and during the Colonial period at least 20 blast furnaces, 45 forges, and iron- works of other types were built in eastern Pennsylvania, which easily led all the other colonies in iron manufacture. During the Revolutionary period others were erected as far west as Fort Loudon, in the Cumberland c alley.^ After 1800 the rapid development of the anthracite mining industry profoundly affected Philadelphia's, development, since transportation of the coal was then necessarily by water, and the streams of the anthracite . regions mostly flowed into either the Schuylkill or the Delaware Rivers. With an abundant near-by supply of coal and iron, with the seat of government, which had been there since 1774, and with a National Bank established there in 1791, one would have seemed safe in prophesying, at the beginning of the nineteenth century, that Philadelphia would permanently remain the leading city of the United States. Education in Philadelphia was at first wholly in the hands of the Quakers, who had established a "Public School" there in 1689, but in November 1739 George Whitefield, who had created a sensation in England by his preaching, though only 24 years old, passed through Philadelphia on his way to Georgia to found an orphan school there. He preached a series of sermons in Christ Church that were so disturbing to the established church that on Nov. 25 the Rev..Richard Peters (who was also Provincial

Jan 1, 1941

Jan 1, 1893

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By Edward I. Salkovitz

THE determination of the orientation of metal single crystals and the studies of plastic deformation are greatly facilitated by the use of the stereographic projection. To draw a standard projection of the crystal it is necessary to have a tabulation of the angles between the various crystal-lographic planes of the particular crystal studied. Bozorth' has published such a table for the cubic system which can be found in many reference books; such convenient tabulation for the hexagonal metals, however, does not appear to be in the literature, although scores of workers have calculated these angles. Therefore, Table I of angles for magnesium, zinc, and cadmium has been compiled. Since the c/a ratio is different for each of these metals, three separate calculations are necessary. The angles 4 between (HKIL) and (hkil) were calculated by means of the formula: Hh+Kk+½(Hk + hK)1+~3aLl cos The c/a ratios were calculated from data given in the 1948 edition of Metals Handbook. Fig. 1 is a typical (0001) standard projection of zinc. For all practical purposes, it serves for cadmium as well, as can be seen from the table. For magnesium, however, it is necessary to construct another net. R. M. Bozorth: Physical Review. (1925) 26, 390.

Jan 1, 1952

By E. S. Machlin, A. A. Hendrickson

Use was made of a recently developed surface-accumulation diffusion technique to measure the self-diffusivity of edge-type dislocation singular lines (Burgers vector along <110>) in a bent and polygonized single crystal of silver. Two factors are involved in obtaining a number for the diffusivity. One factor, the dislocation-line density, was measured by a microscopic technique recently developed, and the value of the other parameter, the effective "diameter" of a dislocation pipe, was estimated. With these parameters equal to 7.3 X 106 dislocations per sq cm and 10-7 cm, respectively, it was found that the self-diffusivity along edge-type dislocation lines was a factor of about two times the average grain-boundary self-diffusivity. The dislocation-pipe diffusivity is about 7x10-7 sq cm per sec at 450°C. THE possibility of short-circuit diffusion through imperfections in crystals has been recognized for some time. It was only recently, however, that concerted effort has been expended to obtain values of diffusivity for grain-boundary short circuits. The work, for example, of Hoffman and Turnbull1 on silver, Fisher&apos;s&apos; analysis of the grain-boundary dif-

Jan 1, 1955

By J. T. Burwell

THE crystal orientation in silicon iron that has been given a particular treatment described by Goss,1 has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualita-tive. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200, It is now generally agreed that Goss&apos;s original conclusion&apos; that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom.

Jan 1, 1940

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953&apos; when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these&apos; provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By A. D. Zunkel, A. H. Larson

Equilibrium arsenic contents of Pb-As alloys in contact with PbO-As2O3 slags containing less than 30 mol pct As2O3, were determined at 650°, 700: and 750 C in an inert at?rzosphere. In this temperature range, the arsenic content of the alloy increased with increasing temperature in the single-phase liquid slag region and decreased with increasing temperature in the two-phase slag region and the single-phase solid-solution slag region. The PbO-As2O3 phase diagram below 22 mol pct As2O3 was determined by thertrzal analysis and by application of a log ?As2O3/?PbO vS log XAs2o3 /x3pbO plot determined from the equilibrium actiuity data. The resulting phase diagram was not well-defined since the eutectic temperature was not detected in the thermal analysis experiments, although a region of terminal solid solubility of As2O3 was found. Results from the phase diagram determination are compared with an existing diagram in the literature. THIS experimental investigation is an extension of a study by the authors1 on the slag-metal equilibria in the systems concerned with commercial lead refining processes such as softening and dross fuming. The first part of this investigation was a study of the slag-metal equilibria in the Pb-PbO-Sb2O3 system. The only experimental work previously done on the Pb-PbO-As2O3 system was by Pelzel2,3 in which the phase diagram for the PbO-As2O3 system was determined below 50 wt pct As2O3 and the equilibrium constant for the reaction 3Pb + As2O3 + 3PbO + 2As was determined as a function of temperature. No slag-metal equilibrium data have been determined. It is due to the scarcity of information regarding the Pb-PbO-As203 system that this work was undertaken. This paper describes the determination of the slag-metal equilibria in the Pb-PbO-As203 system by equilibrating Pb-As alloys with PbO-As2O3 slags in an inert atmosphere, the effect of 1 wt pct additions of bismuth and copper on the slag-metal equilibria, and the PbO-As2O3 phase diagram both by thermal analysis and the use of the slag-metal equilibria data. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade and assayed as follows: 1) 99.8 pct PbO (0.014 pct insoluble in CHJCOOH, 0.02 pct not precipitated by H2S, 0.1 pct CaO, and 0.08 pct SiO2); 2) 99.95 pct As2O3; 3) 99.99 pct Pb; 4) 99.0 pct As; 5) 99.99 pct Cu; and 6) 99.97 pct Bi. Room-temperature X-ray patterns revealed no detectable impurities in any of these materials. Apparatus for Equilibrium and Thermal-Analysis Determinations. The resistance-heated crucible furnace used in this investigation employed nichrome elements and was mounted so that it could be raised to surround the reaction tube during each experiment and, subsequently, lowered. A schematic diagram of the apparatus is shown in Fig. 1. Each charge was heated in a 3+-in.-OD by 31/2-in.-high 416 stainless-steel crucible placed in a 41/4-in.-1D by 18-in.-long fused-silica reaction tube which was closed at one end. On a shoulder around the crucible was placed a 3: -in.-OD by 12-in.-long open-end fused-silica condenser tube. The open end of the reaction tube was covered by a water-cooled brass cap with ports for 1) admitting an inert atmosphere to the system through a stopcock, 2) introducing a stainless-steel, motor-driven, paddle stirrer into the crucible, 3) evacuating the system with a mechanical vacuum pump, and 4) sampling the melt with Vycor sampling tubes. The brass cap was fitted to the open end of the reaction tube with a silicone gasket and collar clamp. The furnace temperature was controlled by a Barber-Coleman Capacitrol controller and a chromel-alumel thermocouple. Due to the corrosiveness of the melt, the controlling thermocouple also served as the measuring thermocouple. The temperature of the melt was calibrated against the controller temperature and was checked periodically during each test with a Vycor-enclosed calibrated chromel-alumel thermocouple. The temperature measurement and control can be considered accurate to ±3°C. Procedure. The charge placed in the crucible for each experiment consisted of 1000 g of Pb-As alloy and 300 g of PbO-As2O3 slag. The crucible was then placed in the reaction tube, the condenser tube was placed on the shoulder of the crucible, the silicone gasket and brass cap were fitted on the open end of the reaction tube, and the entire system was evacuated and filled with argon ten times. After the last flushing, a positive argon pressure of 1 psig was impressed on the system. The furnace was then raised to sur-

Jan 1, 1968

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By Samuel Hoyt

SOME of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc: Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is clue, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that, parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become, accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring, or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. CLASSIFICATION OF MATERIALS ACCORDING TO TOUGHNESS Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may&apos; be deformed plastically, but only by the expenditure of considerable energy. In other words; tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is

Jan 2, 1919

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By Arnulf Muan

PHASE relations in three isothermal sections (l000°, 1100°, 1200°C) of the system Ag-Fe-Pd have been determined as part of a program to develop improved crucible materials for containing low-melting iron silicates at low oxygen potentials. The following experimental method was used: Two- to 3- g samples of each of forty different alloys within the system Ag-Fe-Pd were made up from metals of 99.9 pct purity. The mixed metal powders were contained in a 1-cc crucible of dense recrystal-lized alumina and heated in a protective atmosphere (90 vol pct A, 10 vol pct H2), first to complete melting for approximately 30 min and subsequently at the desired equilibration temperature (1000°, 1100°, or 1200°C) for approximately 24 hr. The samples were then quenched rapidly to room temperature and examined metallographically as well as by X-ray techniques. Unit cell dimensions were compared with standards obtained by study of one-phase alloys of known compositions. The results are summarized in diagrams (a), (b), and (c) shown in Fig. 1. Heavy solid curves outline areas comprising compositions of mixtures consisting of the phases labeled for each area. Mixtures in which liquid is the only condensed phase present are confined to very narrow areas adjacent to the Ag-Pd join at high silver contents. An enlarged, distorted picture of the phase relations prevailing in these areas is shown in the upper-left circular insert. Particular attention is directed toward the misci-bility gap which occupies major parts of the composi-

Jan 1, 1962

By C. G. Dunn, W. W. Martin

Various X ray diffraction techniques have been developed for determining orientations of crystals. Transmission and back-reflection Laue methods1,2,3 in particular have been found to be very useful. In many applications, however, a need still exists for a simplification of the details of analysis so that orientations can be determined more rapidly, and operators with little or no training in crystallography can be easily instructed in the necessary procedures. Filling this need in part is a system of analysis that has been in use for several years in the Metals Section of the Laboratory, General Electric Co., Pittsfield, Mass. This method is an extension of the one of Majima and Togino,4 which uses fifty-five indexed standard transmission Lauemams to cover the entire range of crystal orientations. Greater rapidity in determining the orientation of a crystal is achieved by using a slightly larger set of standard Lauegrams and by systematizing the steps followed. This system of analysis in its present form constitutes the subject matter of the present paper. Although the method uses transmission X ray Laue patterns, many of the operations are applicable to the analysis of back-reflection Lauegrams. Very briefly the method is based on the fact that Bragg and azimuthal angles for two or more identified Laue diffraction spots completely determine the orientation of a crystal, and standard Laue photographs of the Majima and Togino type provide a ready means for identifying Laue spots. After a preliminary analysis, which consists of identifying the pattern in terms of one of the standard patterns, a correctly marked Lauegram is selected to carry out the final analysis. From measured Bragg and azimuthal angles, the normals (poles) of the reflecting planes for the selected Laue spots are located on a stereographic projection and the orient.at.ion of the crystal determined (in terms of the positions of cube poles for example) by a few additional operations on a \I1ulff net. The actual procedure followed will be illustrated in detail after a brief treatment or X ray problems connected with orientation determinations and a discussion of useful principles and techniques. X Ray and Plotting Problems RELATIVE ADVANTAGES OF BACK-REFLECTION AND TRANSMISSION LAUE DIFFRACTION METHODS In the back-reflection Laue method it is easy to make a direct measurement of the tilt of a zone of Laue spots. Specimen thickness also is generally no problem. In the case of thin specimens, however, the time of exposure is less for the transmission Laue method. For example, with silicon ferrite this advantage holds up to a thickness of 0.6 mm if tungsten radiation at 40 kv peak voltage is used. Furthermore, the transmission photograph represents the entire thickness of the crystal whereas the back-reflection picture represents only a surface layer (a thickness of less than 0.05 mm for silicon ferrite), the deeper layers supplying a negligible amount to the diffraction pattern. If a crystal is distorted, the transmission Laue pattern gives more information particularly with regard to the orientation of the crystal and the overall amount of spread in orientation. Finally a 3 1/4 X 4 in. film suffices for transmission photograms; a 4 X 5 in. or 5 X 7 in. film with a central hole is needed for back-reflection patterns Not only is the manipulation of film easier because of the size of film, but

Jan 1, 1950

By I. C. Edwards, W. J. Dengler, D. F. Lillie

By 1959 the milling plant of Bicr oft Uranium Mines Ltd. had been in operation for two years. During this time many changes, both physical and chemical, had been made in an effort to improve plant efficiency. Investigational work had been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of interrelated variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feels that much progress has been made, but there is much yet to be done and many questions still to be answered. The Addendum outlines noteworthy developments to the fall of 1960. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic. nonsegregated, syenite and granite pegmatite. Microline, microline perthite, quartz, sodic plagioclase, and pyroxene or biotite are the main constituents with uraninite, uranothorite, fluorite, titanite, cryolite, calcite, pyrite, pyrrhotite, and molybdenite as important accessories. The mill was designed for a nominal capacity of 1000 tpd with all sections except grinding, leaching, and clarification capable of 1500 tons. Feed was entered to one mill unit on Oct. 29, 1956, and to the second parallel line on November 13. The total feed rate was at 1000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93.0 pct on several months, but a recovery of 92.5 pct appears to be most economical. Operating time for eight months in 1958 has been 97.1 pct although all grinding mills were relined during this period. A generalized flowsheet is shown in Fig. 1 and the plant layout in Fig. 2. The ore is crushed in three stages to -3/8-in. and then is wet ground in two stages to approximately 50 pct -200 mesh. The pulp is thickened to 68 pct solids and agitated by air for 33 hr at a pH of 1.9 as maintained by the addition of 93 pct sulfuric acid. Separation of the uranium-bearing pregnant liquor from the residue is accomplished by five-stage countercurrent decantation (CCD), following which the liquor is clarified for removal of fine slimes. The clarified liquor is treated in the ion exchange equipment in which both the upgrading of the solution and the removal of some impurities is accomplished. Addition of magnesia to the high-grade eluate from ion exchange precipitates the uranium as sodium-magnesium diuranate. After being filtered and dried this precipitate is packaged in drums for shipment. The residue from CCD and the barren solution from ion exchange are neutralized by the addition of lime and pumped to the tailings disposal area. CRUSHING All crushing is done on surface in a conventional three-stage unit consisting of a 36x48-in. Birdsboro Buchanan jaw crusher, a 4 1/4-ft standard Symons cone crusher, and a 4-ft Symons shorthead. Both the two primary and the two secondary screens are 4X 8-ft Symons rod decks. Moisture content of the feed ranges from 3 to 4 pct. In the initial installation the primary screens were equipped with 5/16-in. rods at 1 1/4-in. spacing and the secondaries with 5/16-in. rods at 1/2-in. spacing. With this arrangement the average crushing rate was better than 180 tph. To reduce the work required of the grinding circuit as tonnage was increased, several changes were made in the crushing circuit. By September 1957, both secondary screens had been reduced to 3/8-in. spacing, and rod size had been reduced to 3/16-in. to provide increased open area. Average throughput was reduced to 160 tph. Later, 50 pct of one primary screen was decreased to 1/2-in. opening to better balance the load between the two cone crushers. In May 1958,

Jan 1, 1961

The visitors to the October meeting will be given opportunity to visit the coal fields in Illinois, adjacent to St. Louis, the steam-shovel operations near Pittsburgh, Kan., and the Oklahoma oil fields. The coal mines of Illinois, Missouri, Kansas, Oklahoma and Arkansas furnish fuel over all of the central region of the country. Especially at this time, this district is of importance because of the necessity of producing enormous quantities to meet the country&apos;s demand. Some of the mines produce as much as 5,500 tons in 8 hr., and. the total output of Illinois, alone, in 1916, was 63,000,000 tons. Visitors may see elaborate underground electric tram systems, large underground machine repair shops, surface plants equipped for rapid loading, and some of the most modern coal-washing installations. The conditions for mining here are somewhat simpler than in the east.

Jan 8, 1917

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note&apos; describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris&apos;s latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Cananea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geo- logic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline.

Jan 6, 1954