Search Documents

By Leonardo Pereira

Este trabalho reporta a viabilidade de realizar o tratamento térmico de austêmpera, para obtenção de um Ferro Dúctil Austemperado (ADI), utilizando uma liga de Zn-Al-Mg-Cu, como meio de resfriamento e permanência em patamar, durante o processo de tratamento térmico. Por meio da obtenção da curva de resfriamento da liga Zamac 5, constatou-se a viabilidade de realização da austêmpera em temperaturas superiores a 380ºC. A partir de corpos de prova de ferro fundido nodular de matriz predominantemente perlítica, instrumentados e austenitizados a 870°C e 900°C, avaliou-se a taxa de resfriamento promovida pela liga Zamac 5, até a temperatura de 400°C. O tratamento mostrou-se eficiente, utilizando a liga como meio de austêmpera, sendo registradas taxas de resfriamento superiores a 6°C/s. A análise morfológica constatou a formação de ausferrita, sem a presença de perlita, caracterizando assim a formação do ADI.

Oct 30, 2017

By Nelson SOUTO, Nicolas LEGRAND, Christian COUNHAYE, Don EARLEY

The work is motivated by the automotive customer requirements for a roughness with high peak density (RPc > 75 peaks/cm) on steel sheet surfaces to maintain a good strip surface finish after painting. For that purpose, a new approach is utilized to compute roughness transfer and predict final roughness on uncoated steel sheets (average roughness, skewness, peak density) as a function of temper rolling conditions. The approach is based on the Monte Carlo method combined with the Abott curves and an auto-correlation function to numerically generate roughness profiles for roll and strip respectively. To compute the roughness transfer due to the interaction between roll and strip surfaces during rolling, a composite Abott curve that combines roll and strip Abott curves is used with an asperity crushing model integrated with a rolling model. This enables simulating two roughness transfer mechanisms in the roll bite: the strip asperity crushing mechanism by roll roughness and the strip asperity ploughing mechanism due to roll-strip interfacial sliding speed. The model shows the importance of considering the two mechanisms to predict roughness transfer correctly when strip elongation is high, typically a few percent, and roll bite friction is low. In these conditions, the forward slip at the exit of the roll bite tends to erode strip roughness significantly and decrease considerably the peak density on the strip. For lower elongation levels (~1%) and high roll bite friction, the ploughing mechanism becomes negligible and roughness transfer is controlled by the crushing mechanism only. With these two mechanisms, the model reasonably predicts the evolution of average roughness and peak density over a wide range of temper rolling conditions (new/worn work rolls, hard/soft grades, various elongations), but skewness is more difficult to predict for some trials.

Oct 1, 2019

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Ernst Lindemann

Steel suppliers are required to deliver sheets with particular qualities and with lightweight-potential to the automotive industry. New types of steel call for new production processes. SMS group has developed a new micro-mill-concept, the core of which is the belt caster. This was first built on an industrial scale and has been put into operation and developed together with Salzgitter Flachstahl GmbH. The robustness in industrial-scale operation could be verified. The full use of the belt casting technology, mainly related to energy efficiency and CO2 reduction, is realized with the micro-mill-concept. This is an in-line-process, casting and rolling in one line.

Aug 17, 2017

By Débora Cardoso de Oliveira Silveira, Jean-Christophe Huber, Hamzeh Hamadeh, Kateryna Pastel, Guillaume Brosse

The dynamic behavior of oxygen gas flow, determined by the lance nozzle and blow pattern, is a key factor for determining jet efficiency in BOF Steelmaking. The present work compares the performances of Laval and parabolic nozzles with the aid of the Computational Fluid Dynamics (CFD). The Method of Characteristics (MOC) was applied to design a minimum length parabolic nozzle. The results show that the parabolic nozzle generates more uniform and stable jet, with 2% longer potential core and supersonic length and less shock waves. For the parabolic nozzle, the pressure nearby the nozzle wall is higher, which can protect this region from reverse flow of converter gases and offer longer life for the lance tip. Likewise, the flow rate variations would affect less this nozzle. In addition, the nozzle wear was investigated, and the parabolic nozzle has proven relatively less sensitivity to the presence of this deformity.

Oct 1, 2019

By Michael Brandner

In the past the research and development of new materials for hot mill rolls was mostly done by trials. Such trials are expensive and difficult to transform from small size to the big size of a solid roll. Computation is the cheaper way to get ideas processed and can be varied in different directions. The main part before simulation is the generation of the needed basic data of the specific materials. Some data is already well known and can be bought from databases; others have to be done specifically for our materials. The evaluation of such results has to be done still with solid trials, but the number of trials can be reduced. The advanced techniques of finite element calculation offer a wide range of possibilities to get answers about alloys, solidification, casting parameters and their influence. The possibility to calculate a heat treatment cycle and to get an answer about the internal stress modification during the cycle is a great help to understand the principle of transformation. Examples of different calculations in various fields will be given. The close cooperation with universities and other research institutes as well as the in-house possibilities will be presented.

Jul 30, 2018

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Daniel Horta Fernandes, Walter Gomes de Albuquerque, Adriano Cesar Carvalhido, Victor Dias Martins

O trabalho apresenta a experiência recente da troca de 38 staves contribuindo no prolongamento da campanha operacional do Alto-Forno 3. Durante 13 dias ocorreu a substituição dos Staves originais de FoFo instalados em 1999 por novos Staves de cobre fundido. Além da recuperação do sistema de refrigeração, a mudança no material dos Staves contribui para maior troca térmica favorecendo a formação carga inativa (cascão) que protege os Staves e o corpo do Alto-Forno. Esta substituição foi fundamental para recuperar a estabilidade da temperatura da carcaça e prolongar a vida útil do equipamento até o final de sua campanha. Diversos aspectos do projeto serão apresentados: engenharia, metodologia, planejamento, segurança, qualidade técnica, cronograma e outros.

Oct 1, 2019

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Alessandro Martinis

The performance requirements for modern steelmaking facilities are ever more stringent, as customers and markets are continuously pushing for technologies which allow having high quality steel produced in an economic and sustainable way. In the details, this paper has the aim to present the excellent results obtained by integrated steel plant where an EAF is fed with high quality hot ENERGIRON DRI. The recent technology developments, combined with the affirmed basic process design, contributed to further maximize the energy of the DRI, reaching the EAF at temperatures above 600°C with a carbon content up to 3.5%, as confirmed by plant data. These improved input material characteristics resulted in reduced electrical energy consumption and increased liquid steel production.

Aug 16, 2017

By Caio Trindade Almeida, Tharcysio Oliveira Rocha Paiva

Tharcysio de Oliveira Rocha de Paiva2

Oct 3, 2019

By Lidiane da Paixão Carvalho

Foi estudada uma forma de reduzir o custo de produção de aços que atendem a norma NBR 6656 LNE 38 (ou LNE 380) na Companhia Siderúrgica Nacional (CSN). Esses materiais são utilizados em peças de conformabilidade crítica principalmente para indústria automotiva. Na CSN, o Forno Panela tradicionalmente faz parte da rota obrigatória de fabricação desses materiais constituindo um “gargalo” de produção. Efetuou-se uma análise da composição química, então empregada para os aços e das propriedades mecânicas resultantes, e então se buscou uma nova composição que atendesse a norma e que permitisse outra rota de produção. Percebeu-se que uma redução no teor de manganês em relação ao normalmente utilizado propiciava uma melhor adequação à norma, além de permitir o uso de uma rota alternativa que maximizava a produção e permitia reduzir custos.

Jul 30, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Rainer Fackert

3D-Measurements for slabs and heavy plate are now available and close the gap in the production chain. The measuring systems described in this presentation must be seen as high-tech solutions in the field of casting and rolling technology. The measuring systems were developed taking into consideration the harsh casting and rolling mill environment in which they are to be used, with the aim of achieving high operational reliability and eliminating disturbances. Interconnected quality management systems enable optimization across the complete production process. New limits are being defined constantly for all these developments. What is technically feasible today becomes normal practice tomorrow, and will probably be replaced by completely new technologies the day after.

Aug 16, 2017

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018