Search Documents

By P. P. Olórtegui

El presente estudio revisa los principales conceptos que rigen el diseño de campanas exhaustoras que controlan los procesos con desprendimiento de calor, vapores metálicos y gases, propios de las operaciones de fundición en La Oroya. Asi también, se describe las operaciones realizadas en el primer piso de la Planta de Hornos de Plomo de la Cerro de Paseo Corporation y los primeros pasos de aplicación de los conceptos-teóricos dentro de un programa de revisión y asi mejorar de los sistemas de ventilación exhaustiva.

Aug 20, 1963

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By José Darío Sanabria Cerrón

El presente texto describe la operación de las zarandas de alta frecuencia en la etapa de molienda de las operaciones mineras del país. Durante esta etapa se consume la mayor parte de energía que debe ser aprovechada eficientemente a través de una buena clasificaciónen húmedo de la molienda en minerales para disminuir los costos operativos sobre la base productiva de la planta.

Jul 1, 2015

By K. E. Stanfield

[Asphalt and road oil are the principal products manufactured from Wyoming ?clack oils? which, because of their high asphalt an high sulfur content, are difficult and costly to refine into high-grade motor fuels, burning oils, and lubricants by pre sent methods. Accordingly, the remand for these asphaltic residuums for the construction of roads and other uses is a controlling- factor in the quantity of crude oil produced. The increasing utilization of special asphalts as inexpensive bonding, insulating, and waterproofing materials indicates the desirability of obtaining information on the yield and properties, of asphalts from Wyoming black oil to promote a wider and more stable caret for these asphaltic materials.]

Jan 1, 1941

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By J. Kraemer, A. Preusse

In the federal state of North Rhine Westphalia (Germany) small and medium sized companies are beginning to extract the related gas via old shafts or boreholes and to use it as a source for the production of electricity and heat. More than 100 applications for the separate mining right on mine gas had already been filed by beginning of 2002, since mine gas is treated as a mineral resource under the Federal Mining Law. Meanwhile more than 40 mine gas concessions have been granted and first projects are being developed with encouraging results so far. To enhance the applied techniques and their efficiency Aachen University has formed a research team in this discipline. Scope and goals of this research activities are being presented in this paper. Keywords: extraction mine gas, Renewable Energy Act, Ruhr District.

Jan 1, 2003

By Abraão Santos Silvar

Reformadores primários são amplamente adotados em indústrias de fertilizantes. Nos tubos catalisadores que ficam localizados na zona de radiação ocorrem as reações que produzem o hidrogênio. Também nesta zona são localizados os tubos risers que levam os gases produzidos para o reformador secundário. A fluência é um dos principais mecanismos de danos que agem nestes tubos. O objetivo deste estudo é avaliar os danos causados pela fluência em segmento de riser. Foi realizada análise dimensional, microdureza Vickers, ensaio de tração a quente e análise da fratura. Os resultados mostraram que a fluência foi o principal mecanismo de falha, sendo decorrência da exposição dos risers a temperaturas superiores a de projeto.

Aug 16, 2017

By Renan Barrio de Mendoza

"El presente texto señala la aplicación de nuevas tecnologías conceptos para reducir u optimizar el consumo de energía, como los costos de operación en los procesos metalúrgicos. Así, el uso eficiente de la energía en la actividad minera tiene su impacto en la sociedad -en tanto se emplee adecuadamente en las etapas del tratamiento del mineral. Cabe recordar que en las operaciones de reducción de tamaño de partículas es más barato volar que chancar, así como chancar que moler."

Jul 1, 2015

Metana Minerals commenced life in 1970 and graduated to a mining company in 1981 with the opening of a small alluvial tin-tantalite mine at Wodgina (W.A.) The present board of directors assumed control of the company in 1978 and established the exploration and development philosophies that have guided the company's expansion to its present status as an emerging diversified miner. An ability and willingness to raise equity capital when required has been a feature of the company. Company activities include exploration for gold, diamonds, heavy mineral sands, polymetallic (base and precious metals) deposits, strategic minerals, rare earths, oil and gas in a geographical distribution covering the entire Australian mainland Metana owns and/or operates four gold mines (Reedy, Mt Magnet, Youanmi and Howley) and at the time of writing is developing a fifth gold mine - its first underground mine - at Rothsay. In contrast to many similar or larger sized companies, Metana undertakes most activities itself rather than through the use of consultants or contractors. In-house services include: analytical and metallurgical laboratories, plant engineering design and construction, drilling and mining (earthmoving) Metana Minerals has established an enviable reputation for technical excellence and this expertise has placed the company in a sound position to continue its growth pattern into the future. This growth will be achieved through a combination of low cost and successful exploration and acquisition of suitable mines either directly or through corporate activity.

Jan 1, 1989

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By J. Dumont

"Usualmente en la mina se utilizaban maderos como: redondos, rollizos, pértiga, puntiles, productos de sierra. Posteriormente, con el desarrollo de la entibación metálica, se redujo el consumo de las mismas. En ese sentido, el presente texto describe el uso de la entibación de la madera que comprende los recursos, mercado, estudio morfológico, físico y mecánico, métodos de ensayos, agentes de destrucción, tratamiento de protección de las maderas de minas, entibación y posteo y su transporte en los pozos e interior de los grupos mineros Marlebach y Cuvelette. "

Jan 1, 1961

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Juan Silbino Marceliano Rojas

Volcan Compañía Minera S.A.A. es una empresa minera peruana que inicia sus operaciones en el año 1943. A lo largo de sus 71 años ha logrado posicionarse como la primera productora de plata, plomo y la segunda en zinc a nivel nacional. Durante este periodo la compañía se ha expandido y ha alcanzado excelentes resultados de productividad. Sin embargo, estos resultados no han sido acompañados de indicadores de seguridad favorables. En los últimos 12 años (2000-2011) se han presentado 88 fatalidades, 960 accidentes incapacitantes y 1400 accidentes leves. En el 2012, la dirección de la organización decide realizar un cambio trascendental en la gestión de seguridad, estableciendo como primer objetivo estratégico de la compañía la implementación de una cultura de seguridad de clase mundial para minimizar la frecuencia y la severidad de los accidentes de trabajo. Partiendo de este objetivo en el año 2012 realizó un diagnóstico a nivel corporativo que nos ubicó en una fase de dependencia en relación a la curva de cambio de cultura, tomando como base el concepto de Bradley e identificó la necesidad de efectuar un cambio en dos frentes: Sistema de Gestión SSO y Líderes. Diseñamos una "Estructura Organizacional" en los tres niveles de operaciones, lo que involucró a los líderes y evidenció así el "Liderazgo Visible". El sistema se basó en cuatro pilares fundamentales y aplicó las siguientes herramientas: gestión de riesgos, condiciones, conocimiento y comportamiento. Dentro del pilar condiciones, priorizamos doce riesgos críticos para contener los accidentes mortales e incapacitantes. Los Líderes fueron entrenados en la herramienta de gestión y en los cuatro pilares del sistema. De esta manera se logró el impacto directo en la supervisión y los trabajadores, así como desarrollar las competencias de comunicación, motivación, retroalimentación, confianza y compromiso. El modelo está evolucionando la cultura de seguridad hacia una fase de interdependencia. Hemos reducido los índices de frecuencia en un 55%, severidad en un 92% y accidentabilidad en 96%, sin embargo nuestro logro más importante es la contención de los accidentes mortales a la fecha.

Sep 21, 2015

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By William W. Odell

In Europe and in certain other foreign countries studies have been made, extending over a period of years, relating to the winning of oil from oil shale. More work has been done in these countries than in the United States, for the reason that a supply of natural petroleum has not been so generally available there as here. Information has been obtained relating to present practices in these foreign lands in the development of a shale-oil industry. It is realized that in the past there has been very little inducement to invest capital in shale-oil enterprise in the United State's because the supply of petroleum has been plentiful; however, the time possibly is not far distant when the utilization of oil shale may be cons¬idered a desirable and financially sound venture, as it may be necessary before long to augment our supply of oil with that recovered by processing shale. The data presented herein portrays at least some of the thoughts of those engaged in obtaining oil from oil, shale in Europe, and they depict some of the results thus far obtained as well as certain plans for further efforts to win oil from shale; it is hoped that those who undertake the development of a shale-treating industry in this country will find useful information in this report.

Jan 1, 1946

By J. M. Tannenbaum

A depth-sensing micro-indentation technique is developed for evaluating mechanical properties of materials at elevated temperatures (to 1200°C). System description and design considerations of the test apparatus are described. Based on Hertzian spherical indentation approach, the micro-indentation test apparatus is capable of determining Young?s modulus and creep strength of test materials with flat, tubular, or curved architectures from room to 1200°C under either air or controlled gaseous environments. Calibration tests were conducted on a H13 Tool Steel coupon from 22°C to 500°C and single crystal Haynes 230 alloy at 1000°C with excellent agreement to the literature values. Indentation creep tests of Haynes 230 alloy were carried out at 1200°C with preliminary results showing good correlation to creep exponents. Further system refinements will be investigated, and additional testing will be conducted.

Jan 1, 2010