Search Documents

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway's largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

Study on the Effects and Mechanics of Na2SO3 to Chalcopyrite and Galena

Sep 13, 2010

By J A. Rabe, PAP Fouche, K O?Neill

Two of the most important issues mines have to deal with are tracking the ore mined from pit to plant and to test the efficiency of beneficiation equipment. Kumba Resources and Saco Systems are working together at moment to develop a RFID tracer system to help address these issues. This paper will focus on the tracking of ore from pit to plant. The main advantages for ore tracking is to ensure plant feed blending and dilution according to plan. The RFID tracer system works on the basis of a tracer that physically simulates the ore properties and radio frequency technology that facilitates communication with the tracer and allowing information to be stored on the tracer. This paper tends to indicate the progress on the application of RFID tracer technology in the minerals processing environment as tested at Kumba Resources so far. It is concluded that the system has great potential, but some important problems remain

Jan 1, 2005

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010

By Hornsey R., P. van der Merwe

The Two Rivers Project is a feasibility study to evaluate the UG2 chromitite layer on Dwarsrivier372KT, Mpumalanga Province, South Africa. The project, which commenced in August 2001, is expected to receive go-ahead early in 2003. The project sponsors (AVMIN 55%, Implats 45%)required project delivery within a short timeframe requiring optimization of the geological and geostatistical programme. Geological modelling was carried out in parallel to the drilling programme, and significant up-front geostatistical preparatory work was done. The time saving was approximately 4 – 6 months on project delivery. The cost saving to the project (excluding NPV considerations) is estimated at R20–30 million. Keywords; Two Rivers Platinum, Dwarsrivier 372KT, UG2 chromitite layer.

Jan 1, 2003

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By R. A. Wattenbarger, H. J. Ramey

The trend in gas well testing has been to rely more on the early-time flow data of drawdown and buildup tests than on stabilized flow tests. The stabilized testing methods often are not adequate for complicated modern gas reservoirs because many of these reservoirs have extremely low permeabilities and the transient flow period of a well test can last for days or weeks. It has become common to augment the flow capacity of gas wells by hydraulically fracturing their producing formations. In deep reservoirs the induced fractures are generally vertical and tend to follow a single plane of weakness. The presence of a vertical fracture at the wellbore complicates the transient flow behavior of a low permeability gas well. The flow is further complicated when turbulence occurs near the wellbore. Russell and Truittl published transient drawdown solutions for vertically-fractured liquid wells. They developed methods of drawdown and buildup testing utilizing these solutions, which were based on numerical simulation. Clark2 applied the basic Russell-Truitt solutions to analyze fractured water injection wells by falloff tests. Field examples were given to substantiate the method of analysis. The Russell-Truitt solutions and well testing methods can be extended to gas well flow. Millheim and Cichowicz3 presented the drawdown equations for *Now with Scientific Software Corp., Denver. ideal gas flow, including the effects of formation damage and turbulence. Two actual field cases were presented, both of which exhibited extensive fractures and turbulent flow. For the pressure range of these well tests, the use of ideal gas equations was acceptable. These field cases were significant in being the first published data showing the occurrence of turbulence in fractured gas wells. We, also, observed such cases in practice. Our purpose here is to extend the theory of fractured gas well testing to the flow of real gases. To determine the effects of wellbore storage and turbulence on well test interpretation, we developed a finite-difference model to simulate well test conditions. Since gas wells usually are widely spaced and have high compressibility, the emphasis has been put on the early transient behavior before the effects of the outer boundary are noticeable at the wellbore. The Mathematical Model The geometry of our mathematical model is similar to that used by Prats.4 The well is centered in a circular uniform reservoir. A vertical fracture of infinite flow capacity penetrates the formation and passes through the wellbore. The wellbore itself is not important. Fig. 1 shows a sketch of the problem. Fig. 2 shows the idealized model. The equation for the flow of real gas in a porous medium with uniform porosity, permeability and thickness is5-7

Jan 1, 1970

Validation and Application of Filtration Theory to Plate and Frame Pressure Filtration - From Laboratory to Full Scale

Sep 13, 2010

By Matters C. W

THE following paper embodies the present practice and the results of past experience in the survey departments of two of the leading Broken Hill mines, the Central (Sulphide Corporation Ltd.) and the Broken Hill South S. M. Co. N. L.The authors intend to limit the scope of this paper to a consideration of office methods, as much has recently appeared in technical literature concerning field work, both surface and underground. Special reference may here be made to a valuable paper on 'Mine Surveying' by H W Gartrell, in Vol XIII of Transactions, in which the author gives considerable attention to field work. Moreover, much of the office work described in current literature is American, and sometimes not suited to local conditions, being ·often exceedingly elaborate and demanding a large staff of assistants. It is believed that the methods of recording information described in this paper are sufficiently simple and flexible to be adapted to most Australian mines. Brief acknowledgement must be made to the work done by Americans, who have raised mine surveying to the position of a separate profession, instead of being merely an unimportant branch of land surveying.

Jan 1, 1912

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

Jul 20, 1957

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

Following extensive trials on a 100 000 tpa Research and Development facility at Kwinana, Western Australia, Hismelt Corporation (wholly owned by Rio Tinto) are confident of the future commercial success of this technology. The Hlsmelt process uses iron ore fines and non-coking coals to produce molten pig iron suitable for feeding to BOF and EAF steelmaking vessels. The unique process configuration combines direct injection of raw materials into the molten iron bath, high rates of metal and slag mixing, and effective post-combustion of the bath gases to achieve efficient coal utilisation. This is the key to the strong economic performance of the process.

Jan 1, 1999

By W C. Cook, S J. Mathews, A H. Purvis

The Golden Cross Gold Mine is located at the head of the Waite kauri Ri ver, 8 km northwest of Waihi near the southern end of the Coromandel Range. The mine produces gold and silver from epithermal veins hosted by Miocene andesitic flows and pyroclastics of the Coromandel Group. Golden Cross is owned in joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Company Ltd (20 per cent). Mining is by open pit and underground methods. Mineralisation in a near-surface sheeted/stockworked vein zone is mined from the open pit. The deeper Empire Vein System is mined from underground where higher grade mineralisation is restricted to generally discrete veins. The open pit stockwork zone is west of and offset from the updip trend of the Empire Vein System. The Empire (hangingwall) Vein strikes generally north-northeast and dips steeply west. Dips become subvertical at greater depth. The hangingwall vein is a well developed, generally continuous structure with relatively high gold grades. A complex footwall vein system forms shallow west-dipping offshoots to the hangingwall vein. Structure and gold grades become increasingly erratic away from the hangingwall vein. The better developed footwall veins carry economic grades and high 'spot' grades over 50 g/t Au are not uncommon. Highest gold grades are associated with tightly crustiform banded sections of quartz veins and with dark fine grained siliceous breccias. The main hangingwall vein occupies a major north-northeast trending fault structure, the Empire Fault. Footwall veining forms within subordinate splinter fault zones. There has been extensive multidirectional pre-, syn- and post-mineralisation faulting. Fault manifestation is highly dependent on host rock characteristics. The central part of the hangingwall vein and surrounding silicified country rock has been shattered by a major fault structure, the West Mine Fault, forming a poorly consolidated, blocky quartz-breccia ore zone. Away from the more brittle ore zones and associated silicified envelope, wide clay-filled shears mark the major fault trends. Development of the deposit is considered to have occurred in two distinct stages related to separate episodes of dilational jog movement on the Empire Fault. The first phase reactivated the pre-existing Empire Fault as a dilational fissure with subordinate splinters on the footwall side. The Empire Vein System (hangingwall and associated footwall veining) formed during this phase. A second phase of renewed movement with further dilation resulted in more extensive fracturing of the Empire Vein and surrounding country rock and formed the sheeted/stockwork veining of the open pit. An upwards/westward migration of the hydrothermal system is assumed but fluid pathways between underground and open pit veining are unclear. Ore extraction and mining geology methods have responded to improved understanding of the grade and structural variability, and changing ground conditions inherent in the vein system. The underground mine produces ore from flatback cut and fill, post-pillar and bench stopes. Open pit and underground ores are campaign milled through a conventional CIP plant.

Jan 1, 1993

By Fabricio Reis de Almeida

O presente trabalho tem como objetivo mostrar os ganhos financeiros e produtivos do Laminador de Aços Longos da CSN através da otimização do plano de passes. Analisando a árvore de calibração identificamos a possibilidade de ganhos com a unificação de famílias de bitolas. No laminador temos duas famílias: Família Ø 5,5 mm (bitolas 5,5; 7,0; 9,0; 11,0; 14,30) e Família Ø6,3mm (bitolas 6,3; 8; 10; 12,5 e 16) para a fabricação destas bitolas utilizamos até 18 passes no laminador duo horizontal/vertical e mais ate 10 passes no laminador acabador cantilever. Após um estudo detalhado do plano de passes existente, verificou-se a possibilidade da eliminação e unificação de passes entre as duas famílias. Para corroborar as alterações propostas, decidiu-se utilizar um modelo matemático que representasse os passes e realizasse os cálculos para verificar as reduções e capacidades dos equipamentos visando minimizar os riscos e custos adicionais com modificações de ferramental. Após mais de 60 horas de simulações e testes, foi desenhado um novo plano de passes para a Laminação eliminando-se a necessidade de troca de 8 cadeiras, o que representa um aumento de 6 horas no tempo disponível para produção por mês e também a redução de 8 pares de cilindros de laminação, redução de guias e roletes, e tempo de preparação na oficina de cilindros. Só após verificação e aprovação desta etapa foram iniciados os testes no laminador que confirmaram os resultados obtidos nas simulações.

Aug 16, 2017

By N. Barton, E. Quadros

This paper addresses the prediction of groutable joint apertures, grout penetration limitations, and possible grout take volumes per cubic metre of rock, as a result of 5 to 10 MPa pre-injection pressures ahead of tunnels. Joints are obviously opened more than in the preceding Lugeon tests, and many rock mass properties can apparently be improved if stable micro-cement based materials are used. Cet article concerne la prédiction des ouvertures des fractures injectables, les limites de pénétration du coulis et les volumes injectés par mètre cube, d’après les résultats des injections à l’avant tête des tunnels sous pressions de 5 à 10 MPa. Evidemment les joints s’ouvrent plus que dans les essais Lugeon précédents. Maintes propriétés du massif peuvent apparemment être améliorés si l’on emploi des coulis a base de micro-ciment stable. Die Publikation widmet sich der Prognose injizierbarer Kluftöffnungen, Grenzwerte für Injektionsreichweiten und erreichbarer Injektionsvolumen pro Kubikmeter injizierter Fels, durch die Anwendung von 5 bis 10 MPa Vorinjektionsdrücken vor der Tunnelfront.Die Klüfte werden offensichtlich weiter geöffnet als in den vorhergegangenen Lugeon Versuchen und mehrere Felsparameter können durch die Verwendung von stabilisierten Micro-Zement basierten Injektionsmaterialien verbessert werden.

Jan 1, 2003