Search Documents

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By Turker L

The leaching of Tellness (Norway) ilmenite concentrate in hydrochloric acid and mixed aqueous HCl-alcohol solutions at boiling temperatures was investigated. It was found that the alcohols methanol, ethanol and ethylene glycol all substantially increased the leach rate and in the case of methanol and ethanol this was achieved at lower boiling temperatures compared with aqueous HC.

Jan 1, 1986

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By María Jesús Ojeda

El presente texto describe la aplicación de los principios de exploración geoquímica en un sector de la faja aurífera Nazca -Ocoña correspondiente a la mina "Las Agripiinas". El objetivo es determinar anomalías de oro en base a un muestreo sistemático de afloramientos y niveles ya en desarrollo y así ubicar nuevas áreas favorables para la realización de labores mineros que conduzcan a aumentar las reservas de la mina. La exploración por oro se realizó en rocas metamórficas esquistosas con vetas de cuarzo-pirita, intrusivos granodioríticos y volcánicos andesíticos caracterizados por procesos de dispersión primaría. La dispersión secundaria se determina en óxidos, producto de la alteración de los ferromagnesianos y sulfuros.

May 1, 1986

By J. A. Broggi

América es un continente geológico que contiene riquezas minerales descubiertas, pero que a su vez devela otros valores ocultos en su interior. En este aspecto se requiere la realización de un afloramiento mineralizado en condiciones de visibilidad, a fin de percibir mejor las particularidades que se encuentran ellas y evaluar si los carácteres favorales de tal superficie persistirán en profundidad. Por tal motivo, el objetivo del trabajo es resaltar la importancia de este procedimiento en relación a la demanda industrial, asi como revisar los afloramientos de carácter primario y secundario, en tanto ofrezca un tipo de alteración química en su interior y exterior respectivamente. Asimismo, señale la necesidad de registrar las incidencias de una explotación, como documentos de gran valor para el desenvolvimiento de la geología económica y progreso de la minería.

Jul 20, 1955

The main factors which influence disposal of mine waste under New Zealand conditions are identified and discussed: namely, geological conditions which produce soft weather-sensitive waste, wet and cold winters which affect productivity in such waste, elevated seismicity which affects stability and the need for water rights which involve public participation. The waste disposal scheme for the Martha Hill Project is described, thereby illustrating how these factors influence the planning of a current mine strippings and tailings disposal scheme.

Jan 1, 1986

By Carlos R. Scherpenisse

La voladura es una de las operaciones unitarias en la extracción del mineral, donde se busca un adecuado grado de fragmentación de la roca y se reduzca el costo combinado de las operaciones de perforación, voladura, transporte y chancado primario roca, produciendo a la vez el menor daño posible en las cercanías de ésta. En este sentido, el empleo adecuado del Monitoreo de Vibraciones producto de voladuras, es una técnica que provee múltiples ventajas en términos de examinar en detalle el proceso de la voladura y conocer su eficiencia relativa, su interacción con las cargas adyacentes y en definitiva el rendimiento general del diseño. Por ello, el presente trabajo describe algunos casos de aplicación de la técnica de monitoreo de vibraciones -particularmente en Mina Subterránea y su importancia en el diagnóstico, control, modelamiento y optimización del proceso de la voladura. Asimismo, analiza su potencial en términos de alcanzar substantivas mejoras técnico-económicas, aumentar los rendimientos y minimizar los costos operacionales en esta etapa de la explotación minera.

May 25, 1998

By Esteban Chumpitaz, Miguel Pacoticona, Ricardo Huancaya

El sistema cuenta con una alarma audible dentro de la cabina del camión que alerta al conductor en caso que el sistema detecte una condición de somnolencia. La información es almacenada en la base de datos y explotada gracias a los reportes que el sistema brinda, dichos reportes permiten identificar cuáles son los horarios en los cuales se da mayor incidencia de somnolencia, así como el récord por operador y por empresa. La instalación del sistema ha resultado bastante sencilla debido a que los componentes se concentran en un solo dispositivo que es la cámara Kinect, esta cámara consolida diferentes sensores en un solo dispositivo permitiendo su fácil instalación y adaptación por parte del operador. La implementación del presente sistema mantiene una excelente relación costo beneficio, ya que la inversión a realizar es mínima y el beneficio que se obtiene es bastante importante.

Sep 1, 2017

By Tomoharu Jogo

Dado que el yacimiento de la mina Huanzalá de la Compañía Minera Santa Luisa es delgado, se utilizó el método de corte y relleno para la extracción de minerales. Posteriormente en 1979, se complementa este método con el Trackless Mining, adquiriendo óptimos resultados en la eficiencia y costo de operación. En este sentido, el objetivo del presente texto es describir la aplicación de este último método -en tanto cambio de sistema de explotación- y se muestre la eficiencia del autosuministro de material de relleno en yacimientos pequeños.

Oct 14, 1980

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

By C Verdel, M Lee, A Oorloff, K Welsh

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Thomson Orogen is a large but poorly understood element of Queensland geology. Extensive cover conceals the Thomson Orogen at depth, thus limiting studies to a small number of surface exposures. Previous studies of the northern Thomson Orogen have been restricted to the largest of these exposures in the Anakie Inlier and Charters Towers Province. Less extensive exposures, including Mt McLaren in east-central Queensland, are largely overlooked and poorly documented. Fieldwork suggests that Mt McLaren is a west-tilted fault block of Thomson Orogen metasediments that are at least 2200 m thick. The substantial thickness of these sediments (which we have named the Mt McLaren Formation) and the consistent shallow marine facies throughout the block suggest deposition in an actively subsiding basin. Initial dating of detrital zircons places deposition of the Mt McLaren Formation in the Late Cambrian to Early Ordovician, allowing correlations with formations of similar composition and age in the nearby Anakie Inlier and Charters Towers Province. Both of these areas have a long history of mining and exploration for gold and base metals, suggesting that correlation of basement sequences across these areas could be beneficial for exploration models of the Thomson Orogen as well as for tectonic models of eastern Australia.CITATION:Lee, M, Verdel, C, Welsh, K and Oorloff, A, 2015. Stratigraphy of the Thomson Orogen – new insights from Mount McLaren, north-east Australia , in Proceedings PACRIM 2015 Congress, pp 551–556 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

Inpit tailings disposal has been undertaken at a number of mining sites within Australia. This paper presents a brief history of the experience of inpit tailings disposal at the Marymia Gold Operation in Western Australia, including geotechnical aspects of the design. Regular monitoring of the inpit tailings disposal into the K1SE Pit at Marymia has allowed the operators of the mine to assess the performance of the tailings storage against its predicted performance during the design phase. Results of this monitoring indicated that the predicted performance was exceeded and the results have been incorporated into the design of another large inpit tailings disposal, the K1 Pit. Monitoring of tailings disposal to both the K1SE Pit and K1 Pit has allowed the mine operator to make substantial savings from inpit tailings storage when compared with above ground tailings storage facilities. The inpit method of tailings disposal at Marymia has proven to be acceptable from an environmental perspective by reducing the water resource requirements of the project, backfilling pits, which would otherwise collapse with time and eliminating the need for disturbing additional areas of mining leases, which usually accompanies construction of above ground tailings storage facilities.

Jan 1, 1999

The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure to roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations, and trial-and-error testing. Both prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002

By José Luis Calderón Jiménez

"Dadas las limitaciones económicas de los gobiernos locales y poco apoyo del Estado, la mina Poderosa recibe presión de la población para cubrir el déficit de servicios que requiere el distrito de Pataz y mejorar la calidad de vida de sus pobladores influencia. En ese sentido, la mina desarrolló un modelo de organización que busca fortalecer las capacidades de gestión y presencia del Estadoa través del proyecto que implica el fortalecimiento de los CODECOS mediante reconocimiento municipal e inscripción en registros públicos y la capacitación a los líderes y autoridades en talleres, pasantías y encuentros con expertos. Así, se mejora la relación con la comunidad de forma sostenible y armoniosa."

Sep 1, 2016

By Jean Pool Pillihuaman Carmona

En los procesos de separación del material valioso y la ganga, se consume energía que representa un alto costo dentro del proceso productivo minero. Se estima que este costo equivale a un 35% del precio de venta del metal. Este alto consumo de energía es requerido en los procesos de chancado y molienda, durante los cuales se busca un alto grado de reducción, hasta lograr tamaños, cada vez más pequeños, que permitan conseguir la liberación del mineral valioso, para su posterior recuperación como concentrado. El presente trabajo tiene por objetivo investigar y cuantificar el posible efecto positivo en el costo de la energía involucrada, que se conseguiría al aplicar energía microondas. El ensayo se realizó en roca mineralizada de un pórfido de cobre-molibdeno proveniente de la mina Cerro Verde.

Sep 1, 2017

By Rafael Fernández Rubio

El presente texto señala los mitos desarrollados sobre la cabecera de las cuencas andinas peruanas a partir de los yacimientos minerales situados en el Perú. En este sentido, dichos yacimientos no son el origen de las aguas y por ello, no se les puede declarar zonas intangibles en las que no se otorga ningún derecho para su uso, disposición y vertimiento de agua. Para ello, se revisa el origen de las aguas de escorrentia superficial, evolución de precipitaciones con altitud, las precipitaciones en la vertiente del Pacífico Peruano, del Amazonas y en el contexto global peruano.

May 1, 2017