Search Documents

By Djalma Souza, Rubén Sánchez, Regina Maria Pinheiro, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation up to 10 wt.% on the properties of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis with mass spectrometry. Specimens were prepared by uniaxial pressing at 20 MPa before firing at 750 °C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. However, the waste changes the physical and mechanical properties, generating a deleterious effect on the water absorption and flexural rupture strength of the ceramic.IntroductionAccording to the Brazilian Association of Pulp and Paper, in the last 10 years, the global production of paper grew 35%. Brazil produced 8,2 million tons of paper in 2004 and held the position of the seventh largest world manufacturer of pulp, with about 9,4 million tons per year [1]. The pulp and paper industry generates effluents that present problems related to their disposal, even after the treatment. Among the solid wastes generated by this industry, the main waste is the primary sludge from the effluent treatment plant (ETP).After the initial treatment the decanted solids go through a dewatering stage, generating the solid form denominated primary sludge. This sludge resembles a paper paste of dark gray color when humid, and clear gray color when dry. This primary waste is composed basically of kaolin, pulp, traces of chemical substances and water. This waste generated in the pulp and paper industry depends on the characteristics of the process and of the employed techniques. It can vary significantly from one industrial unit to another, even in the case that the final products are similar. Its composition is approximately 60% of kaolin and 40% of pulp, and these percentages can vary in some moments as a function of the process [2,3]."

Jan 1, 2008

By Richard L. Kerr

The U.S. aluminum recycling industry has experienced rapid growth in both its size and importance over the past two decades. Secondary recovery now makes up about one-third of total U.S .. aluminum supply compared with ]9 percent, of a much smaller total in the early 1970's. This growth has occurred in part because recycled metal performs as well as new aluminum in most applications, and because it provides major savings in production costs and natural resource utilization. In addition, the recycling industry has played a critical role in greatly expanded -production and reclamation of aluminum beverage cans. Recycled metal makes up over half of the content of aluminum sheet used: to manufacture beverage cans. In future years, both the-production and reclamation of aluminum cans are likely to rise in foreign markets, thus providing the industry with opportunities for further growth. Recyclers may also play a larger role in supplying auto producers who are using increasing amounts of aluminum in passenger cars and trucks. However, in order to take advantage of this growing market, an efficient infrastructure for collection of scrap and production of metal must be developed.

Jan 1, 1995

By Cevat Serdar Kucukkaragoz

The kinetics of prereduction of Chromite by carbon was studied under argon atmosphere at temperatures between 1000°C and 1300°C . The compacted and agglomerated specimens were reacted by using a TGA system. The mixing characteristics and the degree of compaction of the chromite and coke particles were the main parameters influencing the reduction kinetics. The reduction rate increased with temperature reaching to 81% reduction at 1300°C. The metallization started as the metallic nucleation around the particles which was first observed at 1100°C. The particles were surrounded by the metallic phase at approximately 40 % reduction obtained at 1200°C. At 1300°C, the reduction proceeded with a high rate during initial stages and with a low rate at final stages. The reduction was found to proceed in the sequence of Fe3+to Fe2+, Fe2+ to Fe(metal) and Cr3+to Cr(metal) with the formation of carbides.

Jan 1, 2006

By Dale T. Peters

In the United States, the United Kingdom and numerous other countries, copper has long been the plumbing material of choice. This has been the case since the late 1920s in the United States and since World War II in the United Kingdom. However, in recent years the plumbing tube market has caught the eye of the chemical industry, and several plastic resins have been introduced to the marketplace as substitutes for copper in household plumbing systems. One of these, polybutylene tube, had so many failures in the United States that a class action law suit was filed, and the manufactures of this product were forced to create a trust fund of nearly one billion dollars to repair damages caused by their product. Chlorinated polyvinylchloride (CPVC), in rigid pipe form, on the other hand, has been mechanically acceptable albeit its recent introduction precludes the test of time enjoyed by copper tube in this application. This paper reviews the State of California's portrayal of copper's environmental effects and will be largely based on the data and information assembled by the Copper Development Association Inc. in its presentation to the State of California in August, 1998 in response to the State's Draft Environmental Impact Report for Chlorinated Polyvinyl Chloride (CVPC) Pipe for Use for Potable Water Piping in Residential Buildings. The paper is intended for use as a model for the use of other copper organizations and individuals in responding to similar situations.

Jan 1, 1999

The entrainment of copper matte in the slag during the slag skimming stage of a Peirce-Smith converter was studied with a dam break model. Experiments were carried out with a range of fluid pairs where the lighter fluid was allowed to overflow a weir and the amount of entrained heavier fluid measured. The resulting entrainment is measured as the ratio of the heavy to light fluid withdrawn. The fluids include oil-water, water- glycerol and salt solutions-water pairs to cover a wide range of densities and viscosities. It was found that the Richardson number, Ri, correlates the entrainment well. For the case of the liquid-liquid interface initially at the same height as the weir, the entrainment was found to vary with Ri-1/3. The transient flow was simulated with a volume of fluid (VOF) code written in-house and used a stairstep approach to represent flow obstacles. The code was validated against the experimental results with good agreement for the variation of the heights of the two fluid with time. The simulation showed that the prevailing mechanism for entrainment is due to a pressure differential created across the liquid in the converter during pouring resulting in the heavier liquid being rotated upwards and over the weir.

Jan 1, 1999

By Bob Drew, Alfred Spanring, Kirschen. Marcus

"Increasing material conversion and energy efficiency, and decreasing carbon dioxide emission levels are crucial for sustainable production processes in the aluminum, cooper, and steel industries. RHI supports these targets by providing a diverse range of solutions including high quality refractory linings, optimum lining maintenance, and process improvements. In this paper examples are provided of process improvements and increased energy efficiency in copper refining, potential energy savings during electric arc furnace and ladle operations in the steel industry, and increased energy efficiency by improved heat transfer in anode baking furnaces in the aluminum industry. In all cases, RHI’s expertise in close collaboration with the customer resulted in an improved performance of the reactor lining and the actual high temperature process with a positive impact on the material conversion and energy efficiency and as a result a decrease in specific carbon dioxide emission levels.IntroductionRefractory linings play an important role in heat transfer during high temperature processes in for example the aluminum, copper, and steel production industries. Due to constantly increasing energy prices worldwide and the increasing demands for environmental and climate protection, improving the energy efficiency and decreasing emission levels of these energy intensive production processes is of significant importance. In this paper, the contribution of modern RHI lining technologies to energy saving measures and the corresponding reduction of specific carbon dioxide emission are described. The type of current refractory solutions for energy intense processes are illustrated with four examples: Optimization and increase of material conversion and energy efficiency in copper refining, energy saving potentials in both electric arc furnace and transport ladle operations in the steel industry, and heat transfer improvements during the carbon anode annealing process in the aluminum industry. These examples focus on particular production processes operating with a high proportion of recycled copper, steel, and carbon anodes. Increased energy efficiency directly decreases the specific energy related carbon emission levels whereas improvements to the metallurgical processes aim to increase material conversion efficiency and, therefore, decrease specific process related carbon emission levels. Significant energy savings can be achieved by maximizing the refractory campaign length through a combination of appropriate refractory material selection, grade zoning, correct installation, careful preheating, and effective maintenance strategies. Besides the efforts to improve the performance and energy efficiency of customer high temperature processes, RHI continuously promotes the development of new low emission carbon-containing refractory bricks and unshaped products."

Jan 1, 2008

By Doon Gibbs

In this talk, we review highlights of x-ray magnetic scattering studies performed during the last decade, concentrating at the beginning on experiments on the rare earth metal holmium.(1-4) Besides intrinsic interest in the x-ray scattering cross-section and its description, studies of this type are motivated by the possibility that new structural and magnetic properties of rare earth metals might be revealed, and that new techniques may thereby be developed. As a result, interest in x-ray magnetic scattering experiments. has grown rapidly during the last 10 years particularly, with the regular application of synchrotron radiation techniques- Magnetic scattering experiments have by now been performed at most of the x-ray synchrotrons around the world. In addition, insertion .device beamlines dedicated to x-ray magnetic scattering experiments are planned at each of the next-generation storage rings presently under construction in the United States (APS), Europe (ESRF), and Japan (SPRING-8). Generally, the results of x-ray magnetic scattering experiments may be analyzed within two regimes of the incident x-ray energy, namely, in the limit of high x-ray energies, when the incident x-ray energy lies above the excitation energy of any absorption edge, and at resonance, when the incident energy lies near an absorption edge. In the high energy limit, the amplitude for x-ray magnetic scattering has the simple form [L(Q)?A + S(Q)?B](5-7) Here, L(Q) and S(Q) refer to the Fourier 'transforms of the atomic orbital and spin magnetization densities, respectively, and the vectors A and B depend on the incident and scattered wavevectors and on the: incident and scattered polarization vectors. 7) Because the vectors A and B are not identical, the polarization dependence of the orbital contribution to the magnetic cross-section differs from that of the spin contribution. This leads to the possibility that the orbital and spin magnetization densities maybe distinguished, in x-ray scattering experiments. The same distinction is not directly possible by neutron diffraction techniques (in dipole approximation, where the polarization dependence of the orbital contribution is identical to that of the spin contribution), and is important to a fundamental understanding of the electronic structure of magnetic materials. A particular

Jan 1, 1992

By Richard Hollis

The Mount Isa copper smelter was expanded in 1998 to a capacity of over 250000 t/y anode copper. This tonnage will be produced from a single stream consisting of an Isasmelt smelting furnace, and four Peirce-Smith converters - one of which was installed as part of the expansion project. During the course of the expansion project Mount Isa Mines Limited (MIM) signed an agreement with WMC Fertilizers Ltd (WMCF) to supply sulphur containing smelter gases over the fence to a new sulphuric acid plant to be built by WMCF. This will result in a further increase in copper production by reducing the time when smelting is curtailed by Air Quality Control restrictions. As well as the need to modify the primary gas system to connect to the acid plant, the hoods and crossover ducts and their support structures on the original three converters required replacement, and secondary ventilation was also needed to improve converter aisle hygiene. Each of these areas was addressed by the project. Preliminary ideas for carrying out the modifications were found to have a serious impact on converter aisle operations, and would have led to a production loss of over 50000 tonnes of copper. Following benchmarking in other copper smelters, a suitable construction plan was developed and carried out to minimise this loss. This paper describes the methodology and construction plan adopted.

Jan 1, 1999

By Zhangm Mingming

Three samples received from the EAF shop were characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work was to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus and to identify their origin and associations with iron minerals in the concentrate samples from the mines. The samples were identified as MINERAL, PELLET, and HRD. The latter is the DRI product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are the major sulfide minerals. Trace amounts of apatite [Ca5(PO4)3(F,Cl,OH)], wardite [Na4CaAli2(PO4)8(OH)8 6H2O], giniite [Fe;(PO4)4(OH)3 2H2O] and vivianite [Fe3(PO4)2 8H2O] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)2O4] in trace amounts in the mineral samples, respectively. Impurities carry over to the pellet and HRD samples. Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed in both the mineral and pellet samples, magnetic and flotation processing routes should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating processes (magnetic separation and flotation).

Jan 1, 2012

By Petr Stehlík

"This paper is aimed at showing and demonstrating progress in technologies and improvements in units for the thermal processing of various types of waste. The following areas are covered: units for the thermal treatment of hazardous industrial waste and common MSW, technologies for the thermal treatment of industrial and sewage sludge, utilizing waste in cement production (material and energy recovery), up-to-date off-gas cleaning systems, original and unique units for the thermal processing of polluted gases, low-NOx burners. The paper represents a review based on industrial applications, papers published in reputable international journals and a monograph under preparation.IntroductionThe present contribution is an overview of the activities and achievements of the Institute of process and environmental engineering (UPEI) of the Brno University of Technology (VUT). The Institute belongs to European leading teams in the field of the thermal processing of various types of waste. The research in the institute currently revolves mainly around a strategic project “Waste and Biomass Utilization focused on Environment Protection and Energy Generation” that is supported by the national government. Due to the limited space this paper is conceived as a review of papers published especially in reputable international journals.Main (strategic) target of the research is development of new, efficient processes (eventually modernized processes with novel original elements) for effective and highly efficient treatment of waste and biomass, including their maximum utilization as renewable energy sources while minimizing harmful emissions. To this purpose, highly advanced know-how for the design and construction of the related technology lines is being developed, supported by mathematical modeling (see e.g. [1]), experimental validation and optimization.Municipal and Industrial Solid Waste – Concept of Waste-to-Energy CentersThermal processing of various types of wastes is not only waste disposal and/or treatment at present. It has to be regarded as waste to energy process wherever and whenever possible and feasible. This observation was at the origin of the concept of new regional Waste-to-Energy Centers (WTEC), outlined in the following paragraphs. The proposal of the centers is based on a combination of experience, know-how and sophisticated approach. The main fact influencing the concept of WTEC is the necessity to treat different types of wastes. Typical types of wastes as well as main products of the processes in a WTEC are shown in Figure 1."

Jan 1, 2008

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By R. Escalera-Lozano, M. Herrera-Trejo, M. A. Pech-Canul, J. López-Cuevas, A. L. Leal-Cruz, M. I. Pech-Canul

"The use fly-ash (FA) and rice-hull-ash (RHA) offers the potential for the manufacture of hybrid Al/SiCp/spinel composites via reactive infiltration, both with recycled aluminum. The main reason behind this statement is the beneficial role that both waste materials play in preventing the degradation of SiCp reinforcements when the composites are processed with aluminum in molten state. Experimentally, MgAl2O4 is formed in situ during the infiltration of SiCp-preforms in the temperature range 1050-1150 oC for 50-70 min in argon atmosphere at a pressure slightly above to that of the atmospheric pressure. Results reveal that both FA and RHA help in preventing SiCp dissolution and the subsequent formation of the unwanted Al4C3; and although FA-composites still might be susceptible to corrosion via Al4C3 -by the interaction of native carbon in FA with liquid aluminum- a proper FA treatment significantly mitigates its deleterious effect. Primary corrosion mechanisms and strategies to overcome the potential degradation effects are outlined.IntroductionOwing to inherent materials characteristics and post-processing complications –such as corrosion damage- development of metal matrix composites (MMCs) from recycling/waste sources might be a challenging task. Fly-ash (FA) and rice-hull-ash (RHA) are two primary waste materials that offer excellent opportunities for the development of Al matrix composites. Due to its singular hollow-spherical shape and low density, FA has attracted the attention of many researchers. For this reason, most of the efforts to develop Al-based composites from waste materials have been centered on the use of fly ash. Extensive research efforts in the use of FA for Al-based composites have been undertaken by Rohatgi and coworkers [1-4]. In addition to lowering costs, incorporation of fly ash into aluminum has been proved to decrease the materials’ density, increase their hardness, abrasion resistance and stiffness [1]. One of the major outcomes from the mechanical evaluation of aluminum composites prepared with fly ash is that related to their compression characteristics. Typical compressive stress-strain curves form A356/hollow fly ash composites show a linear elastic region followed by a plateau (associated to the collapse of the hollow particles), and then an increase in stress, representing densification of the foam. The crushing of the cenospheres in the composites has been related to an enhancement in the energy absorption capabilities of the material and to a better damage tolerance [4]."

Jan 1, 2008

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By Marcel Sturzenegger

Though the extraction of copper is well established, generation of sulfur dioxide (S02) is still a troublesome issue. Conventional processes are further challenged by the increasing amount of impurities in the concentrates. Direct decomposition of the metal sulfides into the metal(s) and elemental sulfur under concentrated solar radiation offers a promising path to solve both problems. Thermogravimetric measurements under inert atmospheres have shown that synthetic chalcocite or chalcopyrite yield copper at temperatures as low as 1773 K. Even though optimum reaction temperatures might be somewhat higher, such temperatures are straightforwardly accessible in solar chemical reactors. The absence of oxygen will reduce the extent of slag forming reactions and thereby alter the evaporation characteristics of volatile impurities such as arsenic or antimony. Chemical equilibrium calculations for a chalcopyrite-enargite feed, e.g., have shown that under inert atmospheres arsenic compounds are completely evaporated at temperatures above 1000 K and an effective separation of arsenic from the matte is expected. An important step towards a solar production of copper is the design and testing of prototype solar chemical reactors for this reaction. Numerical modeling is a key tool supporting a rational design but it requires data of the high-temperature properties that prevail in these processes. Development of techniques for determining the essential quantities such as decomposition rates or radiative properties at temperatures up to 2000 K is therefore a main activity in our laboratory in order to control and optimize the process. Though developed in the frame of high-temperature solar technology, the experimental techniques are also suited to advance the understanding of conventional high-temperature processes. Keywords: Solar technology, Sulfur dioxide, Solar Radiation, Thermogravimetry, Chalcocite, Chalcopyrite, Numerical modeling.

Jan 1, 2003

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000