Search Documents

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By R. Escalera-Lozano, M. Herrera-Trejo, M. A. Pech-Canul, J. López-Cuevas, A. L. Leal-Cruz, M. I. Pech-Canul

"The use fly-ash (FA) and rice-hull-ash (RHA) offers the potential for the manufacture of hybrid Al/SiCp/spinel composites via reactive infiltration, both with recycled aluminum. The main reason behind this statement is the beneficial role that both waste materials play in preventing the degradation of SiCp reinforcements when the composites are processed with aluminum in molten state. Experimentally, MgAl2O4 is formed in situ during the infiltration of SiCp-preforms in the temperature range 1050-1150 oC for 50-70 min in argon atmosphere at a pressure slightly above to that of the atmospheric pressure. Results reveal that both FA and RHA help in preventing SiCp dissolution and the subsequent formation of the unwanted Al4C3; and although FA-composites still might be susceptible to corrosion via Al4C3 -by the interaction of native carbon in FA with liquid aluminum- a proper FA treatment significantly mitigates its deleterious effect. Primary corrosion mechanisms and strategies to overcome the potential degradation effects are outlined.IntroductionOwing to inherent materials characteristics and post-processing complications –such as corrosion damage- development of metal matrix composites (MMCs) from recycling/waste sources might be a challenging task. Fly-ash (FA) and rice-hull-ash (RHA) are two primary waste materials that offer excellent opportunities for the development of Al matrix composites. Due to its singular hollow-spherical shape and low density, FA has attracted the attention of many researchers. For this reason, most of the efforts to develop Al-based composites from waste materials have been centered on the use of fly ash. Extensive research efforts in the use of FA for Al-based composites have been undertaken by Rohatgi and coworkers [1-4]. In addition to lowering costs, incorporation of fly ash into aluminum has been proved to decrease the materials’ density, increase their hardness, abrasion resistance and stiffness [1]. One of the major outcomes from the mechanical evaluation of aluminum composites prepared with fly ash is that related to their compression characteristics. Typical compressive stress-strain curves form A356/hollow fly ash composites show a linear elastic region followed by a plateau (associated to the collapse of the hollow particles), and then an increase in stress, representing densification of the foam. The crushing of the cenospheres in the composites has been related to an enhancement in the energy absorption capabilities of the material and to a better damage tolerance [4]."

Jan 1, 2008

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By Marcel Sturzenegger

Though the extraction of copper is well established, generation of sulfur dioxide (S02) is still a troublesome issue. Conventional processes are further challenged by the increasing amount of impurities in the concentrates. Direct decomposition of the metal sulfides into the metal(s) and elemental sulfur under concentrated solar radiation offers a promising path to solve both problems. Thermogravimetric measurements under inert atmospheres have shown that synthetic chalcocite or chalcopyrite yield copper at temperatures as low as 1773 K. Even though optimum reaction temperatures might be somewhat higher, such temperatures are straightforwardly accessible in solar chemical reactors. The absence of oxygen will reduce the extent of slag forming reactions and thereby alter the evaporation characteristics of volatile impurities such as arsenic or antimony. Chemical equilibrium calculations for a chalcopyrite-enargite feed, e.g., have shown that under inert atmospheres arsenic compounds are completely evaporated at temperatures above 1000 K and an effective separation of arsenic from the matte is expected. An important step towards a solar production of copper is the design and testing of prototype solar chemical reactors for this reaction. Numerical modeling is a key tool supporting a rational design but it requires data of the high-temperature properties that prevail in these processes. Development of techniques for determining the essential quantities such as decomposition rates or radiative properties at temperatures up to 2000 K is therefore a main activity in our laboratory in order to control and optimize the process. Though developed in the frame of high-temperature solar technology, the experimental techniques are also suited to advance the understanding of conventional high-temperature processes. Keywords: Solar technology, Sulfur dioxide, Solar Radiation, Thermogravimetry, Chalcocite, Chalcopyrite, Numerical modeling.

Jan 1, 2003

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By T. A. Venugopalan

The 'Hall-Heroult' Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000

By Lichao Ding, Chunhua Liu, Yunnen Chen

"In this paper the simulated acid magenta dye discoloring the reaction process was researched. The results showed that it attained highest decolorization efficiency for acidic magenta simulation dye wastewater when pH 9 and reaction time 10 min. With the initial dye wastewater concentration increased, the decolored rate decreased. The decolored rate in general kept a tendency to increase with the temperature increased. Kinetics researches showed that when pH 9, reaction temperature 20 and 35 ?, the decoloring reaction process for the dyes accorded with the First-order dynamic equation. The decoloring reaction rate constant was influenced by initial concentration of dye wastewater and temperature.1. IntroductionIn China, textile printing and dyeing industry is one of industrial departments which using more water and discharging more wastewater. There is about 7 billion tons of waste water discharge each year, of which 80% from the process of printing and dyeing. Being complex ingredients, high chroma, more toxic substances and severe environment pollution, the treatment of printing and dyeing wastewater becomes problem urgent to be resolved. The traditional treatment methods such as adsorption [1], coagulation [2], biochemical method [3,4], which has advantages of simple equipment, simple operation and mature process, but they can cause waste accumulation and secondary pollution [5,6].Magenta is a kind of organic compounds, which classified into acid and alkaline magenta. Considering the advantages of simple operation, low cost, simple experiment equipment and friendly to environment, acid magenta dyes wastewater was chose as object in this paper. Some parameters such as pH, contact time, temperature and the initial concentration on of simulative acid magenta dyes wastewater were studied."

Jan 1, 2012

By Robert A. Medower

This paper will review the operational benefits of applying contemporary control technology to balance the blast to a cupola. Reported benefits from existing installations include reduced channelling, higher pour temperature, reduced oxygen consumption, lower coke consumption & reduced emissions.

Jan 1, 2001

By Ho Jung Heo

The proper control of slag composition is a dominant factor affecting yield of iron as well as dephosphorization efficiency in an electric arc furnace (EAF) operation. Moreover, thermophysical properties of slags such as viscosity are strongly affected by the changes in slag composition. Slag foaming, which is also a function of viscosity, is directly connected with the yield of iron and thus optimum slag chemistry are highly required in view of thermodynamics and physical properties. Therefore, we analyzed the slag composition in commercial melt shop (70 ton EAF) with the aim of higher yield of iron as well as higher dephosphorization during EAF process.

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By A. V. Tarasov, V. M. Paretsky

"The design is based on the thermal processing of the wastes in· the intensively bubbled melt in the Vanyukov furnace at the relatively high temperatures (1350- 1450 °C), In this case: -the secondary wastes are not formed; - the especially toxic substances at the outlet from the furnace are absent. The technology was tested on a large scale (on semicommersial bases). Technical and economical basis show profitability of recovery complex for processing of hard garbage waste (HGW) using this technology: the period of capital, investments refunding for the, recovery, complex construction with process annual capacity of 240 thousands tons of wastes is 1,5-2,5 years,"

Jan 1, 2000