Search Documents

By Suzanne Young

The effect of LiF additions on liqt.1id1.:1s temperature and electrical conductivity over a wide range of cryolite bath ratios (1.0 to 1.5 weight ratio) was investigated. Results did not agree with multi-regression equations reported by Dewing and Choudhary over the entire region. New regression equations were developed. Reasons? are given for the differences. The models are used to discuss the economic implications of LiF additions to Hali cell electrolytes.

Jan 1, 1985

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By L. Sh. Tsemekhman

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By K. Krishnapisharody

The phenomenon of slag droplet formation under the action of gas-stirring in steel ladles has been analyzed with experiments conducted in a thin-slice room-temperature model using water and mineral oils as the working fluids. Visual and video investigations have been performed on the interface behaviour along with measurements of liquid velocities in both phases, using the Particle Image Velocimetry (PIV) technique. The measured velocity data and observations on the interface break-up establish that the droplet formation results primarily from an instability mechanism at the interface.

Jan 1, 2008

By Shane Andrews, Gustavo Vasquez, S. K. Varma

"The effect of solutionizing time on the corrosive wear behavior of 2014 aluminum alloy has been studied using the impact and continuous mode of scratching techniques. The transient currents (TC) evolved during the scratching of the alloy shows a linear dependence between the TC and the solutionizing time. Higher TC values at longer solutionizing time may be associated with the changes in the concentration of quenched-in vacancies, grain sizes and dislocations generated during scratching. These factors can either create (a) anodic sites or (b) pitting corrosion resulting in the generation of transient currents. The results have been compared with the similar study carried out for 6061 aluminum alloys. This 6061 aluminum alloy shows similar behavior but the rate of TC generation per unit solutionizing time is much lower than 2014 aluminum alloy. The morphological changes in the impact scratches and the TEM investigation in the scratch have been presented in this paper.IntroductionThe technique of studying corrosive wear of composites of 6061 aluminum in the monolithic and reinforced forms has been reported in the literature [1]. Two modes of scratching, consisting of impact and continuous, in a corrosive environment indicate that the composites, containing 0.10 and 0.20 volume fractions of alumina particles (VFAP), have higher corrosive wear rates than the monolith. A graph between the transient current (TC) generated during the impact scratching as a function of solutionizing time at 540°C indicates linear relationship between them. A similar slopes for the composites were observed and the TC values were less for the composite containing lesser VFAP."

Jan 1, 1998

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By L. Lewczuk

A detailed mineralogical and liberation study was performed on the iron ore mill products from the Scully concentrator of Wabush Mines, Newfoundland. Automated image analysis techniques were applied to deter-mine grain size distribution and liberation of all mineral components of the ore. As a result of the study it was indicated that iron recovery can be improved and the Mn minerals reduced in the iron ore concentrate by (a) increasing spiral middlings, (b) regrinding the middlings, and (c) separating the Mn minerals from the iron minerals in the reground middlings.

Jan 1, 1988

By S. G. Kumar

Experimental studies on high carbon steelmaking through LD Converter - Vacuum Arc Degassing - Bottom Pouring route to produce low oxygen steels were carried out. The results indicated that it is possible to produce steel with a total oxygen content of less than 15 ppm. Thermodynamic and mass balance calculations are made on low-carbon steels that are treated by a complex deoxidation practice based on primary deoxidation of aluminum, manganese and silicon additions; followed by secondary deoxidation of vacuum degassing with simultaneous additions of aluminum. The results showed that primary deoxidation is mainly due to aluminum and the effect of carbon under reduced pressures on deoxidation of molten steel that is already killed by aluminum is negligible. The effect of process parameters on total oxygen content of steel, like carbon content, slag composition and inert gas purging, are discussed.

Jan 1, 1994

By Kenneth C. Mills

Interfacial phenomena can have a dramatic effect on the separation of phases. Furthermore, since they involve surface-active materials, concentrations at ppm levels are enough to cause dramatic effects on separation processes. The effects of (i) emulsification, (ii) contact angle and wettability and (iii) Marangoni flows on phase separation are reviewed.

Jan 1, 1999

By Jiang Fan, Liu Shi, Wang Haigang

Winter-time natural convection in gravel embankments has been suggested as a technique to provide passive cooling and thereby avoid thaw-settlement of roadways located in permafrost areas. Numerical simulation by finite volume method on the proposed model is perf9rmed using the software FLUENT. A gravels model, in which the embankment is composed of stones and air, has been adopted to investigate the temperature and velocity fields in embankment. Simulation results show that in summer, a weak clockwise circulation of the pore air extending throughout most of the embankment. The pore-air motion is very weak which results in relatively straight horizontal isotherm lines. And heat transfer is mainly maintained through conduction. But in winter, pore-air velocities are higher and multiple vortexes are formed in the embankment. Natural convection then becomes the dominant influence on the isotherm shapes within the embankment. As a result of low ambient temperatures exerted on the embankment surface during winter months, an unstable air density gradient develops within the embankment. This convection increases the heat flux out of the embankment. Therefore, the winter-time convection can further reduce the temperature of the foundation soil beneath the open-graded embankment. In addition, the effects of the size of the stones within the embankment have been analyzed and compared in the gravel model. It shows that in winter, 200mm stones lead to stronger vortexes in the embankment compared with those of 60mm stones. Consequently, the zone oflow-temperature beneath the embankment is extended.

Jan 1, 2004

By A. V. Tarasov, V. M. Paretsky

"The knowledge of the true phase composition of the liquid slag is a very important problem, mastering of which grants the possibilities for the scientifically founded choosing of the decoppering method of the autogenous smelting slags. The investigation using different methods of the phase composition of the flash quenched autogenous copper melt's slags has shown, that the most effective method of the slags' decoppering during smelting with the white matte production is the flotation of the recrystallized slags. In this work the authors posed the problem to realize the slags quenching with the rates similar to those, which are used in the modem investigations devoted to the flash quenching of the ironcontaining alloys, with the subsequent study of the quenched samples using the Mossbauer spectroscopy methods in order to establish the connection between the liquid slag's structure and the metals losses with the slag."

Jan 1, 2000

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

Mineralogical and metallurgical scoping testwork were carried out to investigate the production of separate, marketable gold and platinum concentrates. The study utilized a flotation concentrate assaying approximately 5 wt% gold and 5 grams per tonne platinum. The gold-platinum mineralization was recovered from a placer deposit. Optical microscopy and scanning electron microscopy with energy dispersive x-ray analysis identified gold as zoned Au- Ag and Au-Ag-Cu alloys. Platinum primarily occurred as weakly zoned, variably magnetic Pt- Pd-Fe alloys. A combination of gravity and magnetic separations resulted in a gold concentrate grading 86.9 wt% Au (and 9.lwt% Ag) and a separate platinum concentrate grading 400 g/t Pt with recoveries of 94.5% and 96.7%, respectively. Magnetohydrostatic separation (MHS) using the Magstream 200 Separator indicated promising results.

Jan 1, 1994

By Lichao Ding, Jingbiao Fan, Yunnen Chen

"With the development of industrial production, more and more wastewater containing high concentration ammonia nitrogen was discharge into the environmemt, which caused serious harm to the environmemt. Treating the wastewater has great significance to protect water resources. Using air-stripping combined with oxidation to uptake high concentration of ammonia nitrogen wastewater. The influence of operating parameters was investigated. Experimental results revealed that pH of solution, aeration time and aeration strength showed heavy influence on ammonia nitrogen removal. Air-stripping combined with oxidation can be considered as an alternative approach for the removal of high concentration of ammonia nitrogen from practical metallurgical wastewater. When pH was 11, aeration time 20 min, aeration strength 1040 Lh-1, and oxidation with 10 % NaClO solution 10 min, the initial ammonia nitrogen 2130 mgr1 could reduce to 12 mgr1. Other items could also be removed to meet the ""Integrated wastewater discharge standard (GB8978-88)"".1. IntroductionThe rapid development of human activities has caused a worldwide increase of nitrogen in rivers, lakes and coastal waters. It leads to considerable eutrophication and an increase in the frequency of toxic algae blooms [1,2]. The concentrations of nitrogen in the water of China are pervading high [3]. The discharge of wastewater containing high concentration of ammonia nitrogen is one of the most important factors. Great efforts have been devoted to the removal of ammonia nitrogen from wastewater. Traditional methods include biological denitrication [ 4 ], chemical precipitation with magnesium ammonium phosphate [5], electrochemical conversion [6], air-stripping [7] and so on. Biological denitrication is the most common process in the treatment of ammonia nitrogen wastewater. But the process is only suitable for the removal of relatively low ammonia concentration due to the requirement of appropriate C/N ratio [8]. Chemical precipitation needs additional reagents, which may introduce new pollutants to water body. Electrochemical method often uses expensive metal or metal oxide as electrodes, and also consumes large quantity of energy [6].Although air-stripping makes use of stripping tower and consumes energy, it is very suitable for the removal of relatively high ammonia concentration. Different air-stripping conditions would appear different removal efficiency. And only air-stripping the effluent can not be attained the ""Integrated wastewater discharge standard (GB8978-88)"". In this study, we use air-stripping and oxidation to removal high concentration of ammonia nitrogen from simulated and real ammonia nitrogen wastewater."

Jan 1, 2011

By R. Hurman Eric

The dew-point technique of activity measurements take advantage of the volatility of a component in solution. The pressure of the volatile component over a sample is determined from observations of the temperature at which condensation of the vapor occurs. The method is applicable best when the vapor pressure of the components would differ by about two to three orders of magnitude. Experimentally, this is a closed system involving the use of evacuated and sealed transparent quartz sample probes. Furthermore reliable vapor pressure data of the volatile component is essential along with a specialized high temperature furnace capable of giving reproducible results. In this context, the vertical Dew-Point Furnace (DPF) was designed and built after elaborate trails until enough proficiency was gained for reproducible results. Over the years the DPF was modified and improved. The DPF developed was versatile and could easily be used for activity measurements in the isopiestic mode (another method of measuring activities of a volatile component in a solution). The necessary ancillary systems; namely evacuation-flushing-evacuation followed by sealing of quartz sample probes under vacuum were also perfected over the years. As and when necessary the dew-point technique was supplemented by classical equilibration-quenching method employed on the sealed quartz sample probes to reveal necessary phase equilibrium information. The following were studied utilizing the above technique: (i) Activities in CU2S-PbS and FeS-PbS binaries and CU2S-FeS- PbS ternary at 1200°C; (ii) Activities in Cu2S-SnS and FeS-SnS binaries and Cu2S-FeS-SnS ternary at I200°C; (iii) Phase equilibria and thermodynamic in Cu-Pb-S, Fe-Pb-S, Fe-Sn-S, Cu-Sn-S and Ag-Sn-S systems. Most recently the following systems have been tackled: (i) Phase equilibria and thermodynamics in the Ag-Pb-S and Sn-Pb-S systems; and (ii) Activities in Ag2S-FeS-CuzS-PbS quaternary at 1200°C.

Jan 1, 2003

By Yuri Gelfgat

"The report presents the results of theoretical and experimental investigations of the MHD method used for production of composite materials from immiscible melts, e.g., Al-Pb, Zn-Pb, Bi-Ga and others, which, when solidified, can be presumed as ""frozen emulsions""IntroductionThe searching of the methods for controlling the phase distribution in various liquid heterogeneous media is one of urgent tasks in modem material science. The studies [1-3] have revealed that in case of electrically conducting media the influence of electromagnetic body forces on the liquid can be a rather effective mean of such a control. The current paper investigates some physical conformities governing the behaviour of binary liquid metal systems with a immiscibility region under electromagnetic processing designated to produce ingots with homogeneous structure.The main idea of the proposed method rests upon a concept that the electromagnetic forces in the melt are similar to gravity forces due to buoyancy effects in space and have a selective ability to influence the melt components dependent on their conductivity. In crossed electric E and magnetic B fields (fig.I) each component of the medium is influence by the force density f = jXB, where the current density j is determined by the conductivity a of the component j = -oE. When this force is directed parallel or non-parallel to the gravity vector, the buoyancy of suspended particles can be controlled accordingly.This phenomenon allows one to create a situation in binary system, when the sums of all mass forces (gravity and electromagnetic) affecting every component are equal, and two components are under conditions of equilibrium with respect to each other. These conditions are called quasiweightlessness, which is generated in the melt by the electromagnetic forces."

Jan 1, 1998

By B. Q. Li, R. A. Mirshams

"A numerical algorithm is described for the simultaneous prediction of the thermomechanical behavior of the materials and microstructure evolption during metal forging. The numerical development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The finite element code for rigid viscoplastic deformation is developed based on the modification of the existing code for the thermal and fluid flow calculations. The code is tested against and compares well with the results reported in literature. The procedures for the integration of the · rnicrostructure model into the macro finite element model are described. Results are presented showing the characteristics of materials dynamics and mechanical deformation during simple metal forging processes.IntroductionIn industrial deformation processes such as hot rolling and forging, the workpiece undergoes both macroscopic plastic deformations and microstructural evolution. A computer model that allows to predict both materials dynamics and macroscopic deformation is obviously more useful for both fundamental understanding and deformation process optimization. For some industrial applications, especially those involving novel, light and high strength materials, such an integrated model is critical in that both materials and thermomechanical 'behavior during forging must be carefully controlled to obtain the products that meet the desired strength requirement [I]."

Jan 1, 2000

By Mohamed Ahmed, A. Kawy

"Smelting of scrap copper and residual anodes and cathodes carried out in a reverberatory type furnace. In this, deoxidation process is carried out by wood, which acts as a resource of reduction gases such carbon monoxide, hydrogen and methane. Use of wood causes the formation of soot pollutants and efficiency of oxygen removal from copper is low leading to added costs in removing contaminants. This expensive problem was solved by using of reformed natural gas as a source of reduction gases (CO+ H2).IntroductionThree reverberatory furnaces were used for smelting of scrap copper and residual anodes and cathodes. Each furnace had a 7tpd capacity and was operated at 1183 °C.In this furnace, Step1-compressed air supplied by tubes from the side of the furnace to remove sulfur from copper matte by oxidation .The copper is also oxidized to copper oxide .[1]Step 2- copper from matte is deoxidized by a reductant. Typically deoxidation process is carried out using wood as a resource of carbon monoxide, hydrogen and methane which are the reduction gases. Use of wood causes the following:1- Forms soot pollutants2- Oxygen removal efficiency from copper is low; more contamination in copper matte increased energy in deoxidation3-the process is highly expensive.In the recent trends, this problem has been solved by using reformed natural gas as a source of reduction gases (CO+ H) .This results in 1-Reduced pollution during smelting.2- High efficiency in the removal of oxygen from copper to produce oxygen free copper. The surface of copper produced from this method is smooth which helps in forming and machining.3- Low cost and natural gas is more readily available in Egypt than wood."

Jan 1, 2010

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By Yanlong Li, Lifeng Zhang, Ying Ren

In this work, a multiphase mathematical model for the fluid flow in argon-stirred steel ladles was established and validated by experimental measurement of wood's metal. Alloy dispersion in the molten steel was calculated. The melting and mixing of alloy was faster with smaller size of the alloy particles, larger superheat and bigger slip velocity. The current mixing time is approximately 300 s with 30 mm alloy diameter and 91.5 K superheat.

Jan 1, 2014