Search Documents

By A. P. Paiva

Studies focused on the recovery of precious metals by solvent extraction have recently increased. either to devise suitable solvents or to clarify the involved extraction mechanisms and kinetics. In this work, a comparison of the performance exhibited by triphenylphosphine (TPP), bis-(penty1thio)-ethane (BPTE) and triisobutylphosphine sulfide CI"I'BPS) in the extraction of silver from acidic chloride media is carried out. Extraction and stripping isotherms involving the three extractants are presented together with the results obtained on the selectivity of silver extraction against high contents of iron, copper and lead. Attempts to clarify the mechanism of silver extraction by TIBPS were performed by studying the distribution coefficient dependence on ligand and chloride concentrations. The effect of temperature on extraction and stripping is also considered. The interfacial tension for the system, measured with different concentrations of extractant in the organic phase, is analysed.

Jan 1, 1994

By Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Jian-jun Hu

It could significantly increase the leaching rate of refractory gold concentrate containing sulfur and arsenic by roasting pretreatment with adding certain amount of sodium sulfate, and the mechanism of that was systematically researched with DSC, XRD and SEM in this paper. Results indicated that the mechanism of Na2SO4 on double refractory gold concentrate at roasting pretreatment can be summed up in the following three aspects：Firstly, Na2SO4 can react with SO2 and SO3 which is produced by the oxidation of sulfides and generate Na2S2O7(l), which plays buffer effect on sulfides exothermic oxidation, avoiding the secondary-encapsulated of gold. Secondly, the liquid phase of Na2S2O7 can cover mineral particles' surface that possesses a sintering effect, it leads to internal cracks of the particles. Finally, mineral particles will gather with sodium sulfate particles as the center that can improve the permeability of the layer.

Jan 1, 2015

By Suchun Zhang

The alkaline oxidation of refractory gold concentrates containing arsenopyrite and pyrite at ambient temperatures and pressures has been found to be accompanied by the simultaneous dissolution of gold without the addition of cyanide. A detailed study has been made of the kinetics of the oxidation of the pure minerals and of several concentrates. The reaction products of the oxidation of arsenic and sulphur have been monitored using chromatographic techniques. In the case of arsenopyrite, thiosulfate, monothioarsenate, arsenate and sulfite are the principal products while thiosulfate has been confirmed to be the dominant product of pyrite oxidation. Gold, either as added powder or as a constituent of the concentrates has been found to dissolve simultaneously during the alkaline oxidation of both arsenopyrite and pyrite, and this appears to be associated with the in-situ formation of thiosulfate as a lixiviant. The effects of temperature, stirring speed, oxygen partial pressure, alkalinity and pulp density on the oxidation of arsenopyrite and the dissolution of gold have also been investigated. Keywords: Gold, dissolution, arsenopyrite, pyrite, alkaline, oxidation, thiosulfate, thioarsenate

Jan 1, 2005

By S. I. Sobol

The results of the study of the mechanism of a cathode process of cobalt electrolysis to explain disagreements in a form of kinetic equations of autoclave reduction of nickel and cobalt have been used.

Jan 1, 1993

By Tianzu Yang, Weifeng Liu, Lin Chen, Qingkai Xiao, DUCHAO ZHANG

To solve the problem of low leaching ratio of direct gold cyanide leaching from arsenical refractory gold concentrate, this paper proposed a matte smelting process for gold enrichment in low grade copper matte. The effects of copper content in the mixed material, ratio change in slag type, smelting temperature and reaction time on recovery rate of gold and copper were investigated. The experimental results indicated that the recovery rate of gold increased with the increase of copper content in the mixed materials, temperature and reaction time. It was also noted that the recovery rate of gold and copper were respectively 98.16% and 96.39% when the addition of copper content in the mixed material was 3%, slag type of CaO/SiO2 and FeO/SiO2 were 0.6 and 0.9 in 1250°C and the time of reaction was 40min. Most of the arsenic was oxidized into As2O3 existed in the dust. The results showed that the matte smelting method can achieve efficient recovery of gold from arsenical refractory gold concentrate.

Jan 1, 2016

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"The main idea of the report is that the yield surface can be presented as thick, ""foamed surface"" with dimensionality exceeding two. By other words, perhaps, the yield surface is fractal, i.e. it belongs to the class of geometric objects with fractional dimensionality. Apparently, fractal structure of the yield surface is determined by the fractal structure of natural materials. ""Cloud of internal stresses"" term is introduced to describe the stress distribution in representative volume element. Its plastic flow is determined by the interaction of this cloud with the thick yield surface. Thick yield surface and internal stress cloud concepts allow to determine an additional correlation between micro mechanical models of polycrystals and phenomenological theory of plasticity.1. IntroductionClassical plastic flow models are not satisfying the modem requirements. There are two main directions in their development. The first, mathematical, is connected with the development of the general theory of rheological relationships; the second, physical, is connected with the development of the representative volume element (RVE) models which are based on specific ideas about deformation mechanisms. Within the framework of the first direction, the macroscopic experimental data is formalized; the second approach deals with the generalization of physical research results for the different scale levels that are involved in plastic deformation.These approaches have advantages and disadvantages. In phenomenological theories, the advantages are the mathematical simplicity and laconic formulation of constitutive relations, which allows using them in practical calculations. However, the mathematical models of this class can not be considered as general, they are useful only for the description of limited range of deforming processes. On the other hand, physical theories that are based on the description of real plastic deformation mechanisms are very explanatory and predictive, but they lack mathematical simplicity. The above circumstances lead us to the necessity of compromise that can be found in determining the constitutive relations for RVE, which structure and parameters would bear the information about rnicrolevel and mesolevel phenomena. In this synthesis direction, the fundamental role belongs to [1,2], etc."

Jan 1, 2001

By G. H. Khoe

Neutralisation of acid uranium mill tailings with lime or other alkaline materials is usually practised to reduce the dissolved concentration of heavy metals and radio nuclides. Computer modelling of this process was carried out using the geochemical equilibrium code MINTEQA2. Computed dissolved metal and sulfate concentrations were compared with laboratory-based experimental data. It was found necessary to include the modelling of adsorption of trace metals (such as uranium and lead) by the precipitated ferric hydroxide in order to obtain acceptable concentrations in the neutralised liquors. There were limitations of the modelling exercise due to important aspects which were not addressed or properly accounted for such as chemical reaction kinetics and the effect of high ionic strength. These are discussed in the paper.

Jan 1, 1991

By Zdzistaw MiGzkowski

At KGHM Polska Miedi S.A. a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass ex-change inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed. The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ? The second zone moves slower into the grain and the rate of the movement is deter-mined by the presence of oxygen. In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined. The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By W. -D. Schneider, B. Schwab

Like all metals, zinc can be recycled theoretically without end. To demonstrate environmentally friendly use of zinc, it is necessary to increase the recycling rate. In this regard, the Imperial Smelting Process developed in the forties and fifties in the United Kingdom has become more and more important. This unique process combined with a sinter plant, hot briquetting, and direct injection through the ISP furnace tuyeres offers ideal possibilities to recycle all kinds of zinc and lead bearing materials. Possible secondary materials include Electric Arc Furnace (EAF) dust, zinc-containing sludges and even zinc/carbon batteries. This high temperature process also destroys all organic materials, like dioxin, and can be seen as a sink for many harmful substances.

Jan 1, 2000

By M. Demuth, B. Holleis, M. Potesser, D. Spoljaric

"In 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today's and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Warme-Institut ""GWI"" in Essen (Germany) and the University of Leoben, different new burners have been developed.The efficiency of industrial combustion processes can be increased in two ways (which can be seen in Figure 1 ), either by preheating the fuel and combustion air or by adding oxygen. Due to the high 79 % Nz ballast in air combustion, only low flame temperatures can be reached. This results in high heat loss in the exhaust gas, caused by the low combustion efficiency. Oxygen can be introduced into the combustion chamber using different techniques:• Oxygen fuel burners• Direct oxygen injection into the fuel air flame• Underlaying of the fuel air flame• Enrichment of the combustion airIn Figure 2, the theoretical flame temperature for the stoichiometrical combustion of natural gas is plotted as a function of oxygen enrichment. Therefore, it can be concluded that even low enrichment values produce higher flame temperatures and result in higher combustion efficiency."

Jan 1, 2012

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By Chen Song

In the experiments of purifying the solution of chlorine leaching from nickel concentrate with N235, the effects of organic phase composition on purifying efficiency have been studied. From the results obtained, the optimal organic phase composition is found to be 25%N235+12%isomerous alcohol +63%sulfonic kerosene (VIV) and the saturated content of cobalt in organic phase is7.95 g*dm3. And then the serial experiment is carried out. The results show that at the given organic phase composition, the purified solution contains p(Ni) >200 gm dm3, p(Ni)l p(Co) >50000 and the contents of Cu, Fe, Mn, Zn meet the technical criterion of standard nickel electrolyte. The cobalt chloride solution contains p(Co) >I10 g L-1, p(Co) lp(Ni)>50000 and the enrichment of cobalt has been achieved.

Jan 1, 2006

By Alicia Esther Ares, Carlos Enrique Schvezov, Alejandra Silvina Roman, Claudia Marcela Méndez

In this paper the structure of aluminum based alloys and their corrosion behavior by using different electrochemical techniques as characterization methods are considered. Currently, it becomes imperative to know the role of the Al2Cu against the susceptibility to corrosion of these alloys. The present work aims to studying the electrochemical behavior of aluminum base alloys with the following compositions: Al-1wt.%Cu, Al-4.5wt.%Cu and Al-15wt.%Cu (with different grain structures), in 1M NaCl solutions, at room temperature. Cyclic potentiodynamic polarization tests were performed and were found that the alloys with more than 1wt.%Cu in the matrix have an unstable behavior and without tendency to reach passivity. The equivalent circuits derived from electrochemical impedance spectroscopy technique (EIS) generally showed two capacitive contributions. The susceptibility to corrosion becomes a complex function, not only of copper concentration and structure, but also with interdendritic spacings and distribution of phases in the alloys.

Jan 1, 2015

By G. Kugler, M. Tercelj

"The use of the up-to date light alloys and their development are in the sharp ascent especially in transportation industry. In the last years the use of the magnesium alloys for the various purposes was strongly increased. The aim of present research was to study the influence of solidification rate on hot workability and on obtained mechanical properties of AM60 magnesium alloy. The study was also focused on possibility to omit prior homogenisation process which would result in cost reduction. The solidification of gravity cast alloy has been investigated with various methods of the thermal analysis: in situ simple thermal analysis and simultaneous thermal analysis. In order to reveal optimal hot working conditions the deformation behaviour was studied in the temperature range 200-450°C and strain rates between 0.001-lOs-1. Mechanical properties have been studied with tensile and impact toughness testing.IntroductionIn recent years, the increased demand for magnesium alloys has been mainly driven by the need of automotive and transportation industry to reduce the weight, as this is the most important parameter to reduce the energy consumption. Beside their very low weight in comparison to other metals, the magnesium alloys are characterized by good machinability, corrosion resistance and good mechanical properties, and can thus compete with aluminium alloys and for some applications even with steels. Due their decreased workabilty they are typically used as cast alloys, but in recent years also the research of their wrought state has become more extensive [1-7]. Decreased hot workability of magnesium alloys originates from their hexagonal close-packed structure. One of the most popular magnesium alloys with great potential for many applications is AM60 (MgA16Mn), which is predominately used for casting. But its application could be increased if the mechanical properties, could be improved. This can be done by hot working. Namely it is well known that wrought microstructure is characterized by better mechanical properties in comparison to as-cast state. On the other hand due to its low hot workability the homogenization process is required prior hot deformation, which results in increased production costs. Thus the aim of the present research was to study the influence of solidification rate on hot workability of AM60 alloy in order to improve its mechanical properties and to check the possibility of producing near-net-shape casting products omitting homogenisation process by employing small additional deformations after casting. Within the framework of this research the solidification of gravity cast AM60 alloy has been investigated with various methods of the thermal analysis."

Jan 1, 2011

By Dr. -Ing. Wolfgang Pietsch

Many primary metallurgical wastes are in the sh.-ape of turnings; borings, chips, dusts, and other particuletes. While such. materials can be easily segregated and/or upgraded to yield high quality ?secondary metals with often known composition for easy recirculation into the production? process; their particulate nature results in various problems. Roller presses are used in an ever increasing number for size enlargement and densification of primary particulate metallurgical wastes for secondary metal recycling. The paper will mention the areas of application from A(luminum) to Z(ink), also including Brass; Cast Iron, lead, and Stainless Steel, as well as dusts from all types of melting and ladle furnaces or converters. Typical systems using roller presses for size enlargement. will be discussed.

Jan 1, 1995

By Denise Corrêa de Oliveira

Household zinc based batteries, dry and alkaline, has become the most popular sources of electrical energy, and are widely used. Because of their heavy metals content such as mercury, zinc and manganese, spent batteries cannot be directly placed in common landfills without a pretreatment. As a municipal solid waste, these batteries may cause serious health problems and environmental impacts. These damages can be reduced by recovery (which means saving natural sources and energy), recycling and adoption of cleaner technologies. Although this worry has been increasing recently, and producers are doing efforts to reduce the mercury content, batteries still need proper safe disposal conditions or recycling processes. This work presents the efforts in progress to characterize and recycle mixed - dry and alkaline - spent batteries, by using low cost unit operations. Some possible recycling stages and recovery parameters of metals as zinc and manganese are also discussed.

Jan 1, 2001

By R. G. Reddy

Nickel solubilities in spent pickling solutions (i.e. HF-HNO3-H2O solutions ) were measured as a function of HF and HNO3 acid concentrations. The chemical analysis of the industrial pickling solutions and sludges were made. The stable phases observed in the sludges are FeF3?3H2O, and ( FeCr ) F3?3H2O. Pure Ni, and stainless steel type 316 were used in this study. The results showed that the solubility of Ni increased with increase in concentrations of HF in pickling solution at a fixed concentration of HNO3: An excellent agreement between the experimental solubility data and the theoretical data was obtained. X-ray diffraction analysis showed that the solid solubility product formed is mainly NiF2?4H2O compound.

Jan 1, 1992