Search Documents

By Adam Mackenzie, Dan Payne, Yass-Marie Rutty

"Historically, the Crinum mine has experienced significant falls of ground when longwall production slowed to prepare for recovery in weak roof areas. These conditions continue through the recovery process and result in both safety concerns and delays. When mine plans and exploration revealed that most of the mine's future longwall recoveries were located in weak roof areas, a decision was made to try pre-driven recovery roads as a solution to the problem. After completing eight pre-driven recovery roads with varying degrees of success and numerous lessons, the Crinum North mine now utilizes a modified Pre-driven Recovery Roadway (PDRR) to improve the longwall take-off process in weak roof areas. During mine development, a standard roadway is driven where the final recovery location of each longwall is planned. After the installation of secondary support, the PDRR is backfilled with a cement-flyash mix to provide support to the roof, and confinement to the ribs and floor of the roadway. The method has been refined over the last four years to provide greater strata stability and improved operational and safety performance compared with conventional take-offs at Crinum, and has resulted in a site record of longwall relocation in 11.5 days (pull mesh to picks in coal). This paper describes the evolution of the PDRRs from Crinum East to Crinum North, including lessons from initial attempts and changes to the secondary support regime, the operational approach during the final stages of retreat, the backfill strategy and plans for the future.INTRODUCTIONThe Crinum mine is the underground component of BHP Billiton Mitsubishi Alliance's (BMA) Gregory Crinum mine, located northeast of Emerald, Queensland (Figure 1).The Crinum mine has a history of roof control problems coming into and during longwall recoveries. Weak roof, combined with the slow mining, which is a consequence of preparing for equipment recovery, pulling mesh (which also creates tip-to-face issues), and the lengthy bolt-up process, often results in loss of immediate roof and subsequent roof falls. In fact, approximately 50% of the first 13 longwall recoveries (which were at depths of 180 to 200m) experienced roof fall delays, the longest of which took four months to mine the last pillar and recover the longwall. This recurring problem prompted the mine to investigate options to reduce or eliminate the problem."

Jan 1, 2016

By J. R. M. Hill

The U.S. Bureau of Mines is involved in research to improve geological sensing (or geo-sensing) techniques. This paper presents results from field trials of two research projects concerned with new technologies for geosensing. The goal of the first project was to develop a "smart" roof bolter drill so that it could probe into roof rock to evaluate rock conditions. The goal of the second project was to modify an existing mine-wide monitoring system in a continuous mining operation so that the system could interface with geotechnical instruments to provide near real-time geosensing. Integration of this mine-wide monitoring system with the smart roof drill to collect, reduce, and analyze geotechnical data and the potential applications of the resulting technology in mining, are described.

Jan 1, 1992

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By J. K. Whyatt

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that. within the scope of this study, the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard. However, much work will be required to make good on this promise.

Jan 1, 1998

By Gustavo Herrera Rico

As part of a general effort to increase safety, efficiency, and profitability of its mining operations, MICARE personnel with the support of NorWest Mine Services, Inc. determined that the key to improving development mining was the implementation of roof bolting as the means of primary roof support for both main entry and longwall gate road development. Until mid-1994, MICARE had relied exclusively upon primary roof support systems composed of heavy steel beams and wooden posts. Support systems were designed, implemented, and evaluated that were successful in controlling the mine roof under extreme geological conditions. This paper describes the geological challenges, support selection criteria, and presents the instrumentation and 'mine measurements made to assess the bolting performance during the development and retreat mining process of longwall mining.

Jan 1, 1997

By Winston Gale

This paper is presents a summary of recent investigations into fracture and caving about longwall panels. The results of these investigations indicate that rock failure initiates well ahead of the longwall face. Rock fracture typically forms in response failure through the material and bedding planes. Tensile fractures also form in massive units. These fracture patterns typically create a fracture network which determines the caving characteristics encountered at the faceline. The action of longwall face supports under such conditions is to maintain confinement to the fractured ground and develop a consistent caving line, The confinement developed above the canopy under these conditions can be variable on a shear by shear basis and the operational face support procedures play an important role in stability about the face area.

Jan 1, 2004

By Eric G. Zahl

Researchers at the Spokane Research Laboratory of the National institute for Occupational Safety and health are evaluating stress and displacement measurements in a longwall coal mine. The objective is to determine the best indicators of coal bump hazards during operations so that mine foremen and technical stall can make more informed intervention decisions to protect miners from coal bumps. Instruments were clustered in two panels, a yield pillar, and the immediate roof and floor of a two-entry longwall coal mine. Data were gathered continuously from a variety of instruments as mining proceeded toward and past the instrument cluster. Researchers and the mine's technical staff evaluated these data with respect to coal bumps and bump mechanisms. Selected graphs were then presented to mine foremen on a periodic basis to test their usefulness in identifying hazards. Of particular interest was the use of horizontal stress data from the immediate roof. To measure changes in horizontal stress, a new technique was devel¬oped for installing a grouted biaxial stressmeter in the roof. An evaluation of the development of this stress monitoring system in producing data beneficial to mine foremen is presented.

Jan 1, 2000

By Mario G. Karfakis

Mining related subsidence is a major concern over abandoned shallow coal mines. Many of the subsidence prone areas are presently used or will be used in the future for residential housing development. Concern over mine subsidence is inhibiting the development of surface land uses on previously mined area. This concern prompted public officials to realize the need to develop guidelines which can be used to assess and reduce the risk of mine subsidence damage to building and other improvements. Subsidence and the associated ground movements must be defined before one can relate them to building damage. Surface movements resulting from underground coal mining occurs in two phases termed as: active subsidence and residual subsidence. Active subsidence refers to all surface movements occur in^ simultaneously with the mining operations, while residual subsidence is-that part of the surface deformation which occurs following the cessation of mining. Residual subsidence is the major concern over abandoned mine lands. The duration of residual subsidence is of particular importance from the standpoint of damage at the surface to structures built after the mine has been abandoned. Time spans during which surface subsidence may occur, vary markedly with the mining method being used. In total extraction methods, such as longwalls, subsidence is induced rapidly, beginning almost immediately after mining. Subsidence concurrent with coal extraction is desirable for a safe longwall mining operation. Usually subsidence is complete within a relatively short time. The remaining settlement occurs as residual subsidence due to the gradual compaction of the subsided ground. The relative proportion of the residual subsidence movements is dependent upon the presence of remnant pillars and roadside packs. rate of face advance and depth of workings. In partial extraction methods, such as with room-and-pillar systems. major occurrences of surface subsidence may be delayed for decades until the support pillars and/or the roof have substantially deteriorated and collapsed. The actual time involved depends on a number of factors such as the strength of coal, roof, and floor, extent of fracturing. presence of water, depth of workings, pillar size and percentage extraction. Consequently residual subsidence is more likely to occur over abandoned room-and-pillar mines. The following sections define subsidence over abandoned mines, review the proposed mechanisms, identify the controlling factors and examine the prediction methods.

Jan 1, 1987

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By S. K. Sharma

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae, Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar strength.

Jan 1, 1992

By A. Wahab Khair

This paper presents an analysis of surface ground movements recorded from two longwall mines in Northern West Virginia which operate in the Pittsburgh Seam. The instrumentation areas consisted of four panels, two at each mine, covering various sections with unique topographic features. Instrumentation consisted of survey monuments on 25 to 120 ft. spacing. Vertical and horizontal ground movements were measured at specified intervals to determine subsidence rate, developing and final subsidence profiles, angle of draw, horizontal displacements and associated strain profiles. A relationship between panel depth and width and the subsidence factor was also developed.

Jan 1, 1988

By Robert C. Garson

The Mine Roof Simulator at the DOE'S Mining Equipment Test Facility is described. Its use in the research and development on the behavior and response of longwall roof supports to simulated mine environment is investigated. Advanced technology analysis methods such as finite element modeling, strain gage instrumentation, and photoelastic techniques are investigated for application in roof support design two case studies are presented of test data and results.

Jan 1, 1982

By Z. T. Bieniawski

A major study was performed on determination of long term strength of coal strata directed to the design of coal pillars to ensure their stability beyond the life-time of a mine. Based on field investigations, numerical modeling and reliable data from 12 case histories, three aspects of time effect in the strength of coal strata were studied; (1) strength reduction based on the concept of volumetric strain estimate from in-situ tests, (2) strength reduction in terms of three failure criteria applicable to coal strata: original Hoek-Brown criterion, modified Hoek-Brown criterion, and Generalized criterion, and (3) long-term strength estimation as a function of coal strata quality RMR based on case studies. From these investigations, an integrated approach to long-term pillar stability is proposed, based on numerical modeling and empirical pillar strength formulation. The values of factors of safety for coal pillars are analyzed in terms of probability of failure and practical meaning for mine design purposes.

Jan 1, 1994

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

Tailgate pillar and tailgate-face corner humps have been a major threat to longwall coal mines where hump-prone conditions exist. The yield pillar design concept, in which the longwall chain pillars are designed in such way that they can yield in a nonviolent or controlled manner during longwall retreat, has been used in many longwall mines to prevent tailgate pillar humps. However, this practice often shifts the side abutment load onto the tailgate-face corner especially when a massive and strong sandstone member is present within the caving zone or in the vicinity of the coal seam. Therefore, the abutment pillar design concept has also been used in some hump-prone coal mines to minimize the stress concentration on the tailgate panel rib for the control of tailgate-race corner humps. The disadvantage of using the abutment pillar design concept is that it is more costly and puts additional pressure on mine operations for gate entry development and significantly reduces the recovery of coal reserve. In addition to pillar size, panel layouts. such as the panel width and panel orientation also play a critical role in pillar or face humps and should he taken into account. Based Upon the Cyprus mine design and operational experiences at Willow Creek and case studies at other bump-prone longwall nines in the U.S., the authors attempt to identify the critical factors causing coal mine bumps and to introduce some guidelines and criteria for the design of both yield and abutment pillar systems and panel layouts.

Jan 1, 1999

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002