Search Documents

By A. T. Iannacchione

Numerical simulation of coal pi1lar loading has traditionally been a difficult task due to the unique and highly variable properties of coal and the inability of numerical procedures to duplicate these properties. This simulation was based upon material properties developed from laboratory tests of coal cubes and examined against coal pillar strength data developed from actual underground measurements. The coal cube measurements indicated the coal followed a nonlinear Mohr- Coulomb failure criterion. The in situ measurements showed that a pillar yield zone developed similar to Wilson's hypothesis and, at high confinements, the pillar core seemed to followed a pseudo-ductile behavior. The strain-softening material model, based on a 1inear Mohr- Coulomb failure criterion, simulated coal cube and pillar behavior at moderate load conditions. However, at high loads the models were inaccurate, due to an inadequate failure mechanism and/or to changes in the pillar constraints at the coalbed interface.

Jan 1, 1989

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

By Y. M. Jiang

A users friendly PC Computer Program has been developed to implement a systematic design of the powered support. The required input data are: (1) thickness, RQD, and compressive strength of the immediate roof; (2) mining height; and (3) type, thickness, and tensile strength of the main roof. Several important parameters for support selection under a given geological condition are generated through the implementation of the program, including type of support most favorable for the geologic condition, minimum inclination angle of the legs with respect to the horizontal axis, suitable setting load ratio of the front to rear leg for the 4-leg supports, optimum setting load, and support capacity.

Jan 1, 1989

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

By S. L. Huang

The location and shape of potential failure surfaces in soil slopes were directly determined based on the stresses induced in the soil mass and the strength of the soil itself. Stress calculations were carried out by the finite element method with the Drucker-Prager nonlinear material model. The Mohr-Coulomb failure criterion and Mohr's circle stress analysis were then applied to the calculated stresses to determine the characteristics of the failure surface.

Jan 1, 1989

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By Po-Ming Lin

Stress has a significant effect on the stability of pillars. In order to get an accurate picture of pillar stability, one needs information not only on the primary Stress distribution but also on all the Subsequent Stress changes as time passes. Sonic methods are some of the fastest, most economical and least destructive means of stress prediction. The wave propagation velocity has long been applied to the investigation of the upper mantle and crust stress. Recently, it has also been applied to the prediction of rock bursts and to mine site investigations. Another parameter for investigating stresses in rocks is the attenuation coefficient. Attenuation has been observed to be more sensitive to stress changes than wave velocity; however, the measurement of attenuation is more difficult than that of wave velocity. In this paper, the mechanism of sonic attenuation in rock is reviewed. Both the velocity and the attenuation of sound waves in five different rock types under various stress fields were examined in the laboratory. It was found that for a specific rock type the relationship between the velocity ratio and stress, as well as that between the attenuation coefficient ratio and stress, can be expressed by simplified second order polynomial equations.Research showed the attenuation coefficient to be more sensitive to stress change than the velocity ratio. A field investigation method was proposed using a Schmidt hammer as a repeatable energy source. Initial trials appeared to show that monitoring by the wave attenuation method gave more repeatable data than monitoring wave velocity.

Jan 1, 1984

By Raymond A. Mazzoni

Over the last twenty years, roof support technology has made numerous advances since the original wedge and slotted bolts of the 1950's. By comparison, the roof supports used today are more complex and specialized than the supports used in the past, providing mines with a varied selection of supports from which to choose. As a result, when problems with supports are encountered, it is more difficult to determine whether it is the result of geological changes, poor installation practices, or malfunctioning supports. Recognizing this problem, MSHA's Roof Control Division of the Pittsburgh Safety and Health Technology Center, has undertaken the task of publishing a guide for trouble¬shooting problems encountered with roof support systems. The purpose of this guide is to provide a logical sequence to resolving the most common problems encountered with roof supports. The objective of this paper is to introduce this guide to the mining industry as well as provide insight into the evolution of the guide from its beginnings as rudimentary charts to its more comprehensive present format as a practical guide for use by the mining commu¬nity.

Jan 1, 1997

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012