Search Documents

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By Howard N. Egan

The importance of coal as the major energy source has led to wider interest in the recovery of waste coal fines as a usable product. An additional incentive for fine coal recovery has been the increased emphasis on environ- mental pollution control and conservation of the nation's natural resources, Accordingly, a series of studies and tests were performed to investigate the feasibility of the recovery, concentration, balling and pelletizing of coal fines as a marketable adjunct to existing mining and beneficiation operations. These studies were conducted at the existing operations of the Eastern Coal Corporation at Stone, Kentucky, and the Metallurgical Laboratory of Arthur G. McKee & Company in Cleveland, Ohio. The purpose of the investigations was to recover the fines from the effluent waste waters of an existing preparation plant and transform them into a high carbon, low sulfur and ash product capable of being handled with a minimum of degradation and dusting problems. The fines were relatively high in ash content prior to processing, and flotation pretreatment served a combined function of beneficiation, recovery and water clarification, The minus 28 mesh coal concentrate containing 40 to 45 percent minus 325 mesh size material had an ash content varying between 5 and 7 percent and a sulfur content of less than 0.5 percent. Chemical and size analyses of the effluent and concentrated fines are presented in Table I for comparison.

Jan 1, 1967

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020

By Edwin R. Phelps

Good morning ladies and gentlemen - today I am in an enviable position for two basic reasons - No. 1, since I am first on the program, the audience should start out awake because those that partied too much last night are still asleep, but in their room, not here. No. 2, since copper, iron, and mining technology are not competitive, the veracity of my statements will not be questioned. Most such meetings I attend are based on the subject of energy and the coal industry does have competition from oil, gas, hydro, and nuclear. However, to counteract this advantage I am the usual engineer with a limited vocabulary by schooling, and the remaining vocabulary almost completely eliminated due to the presence of ladies. In relation to the past of the coal industry, we have not only suffered the competition of other energy sources mentioned before, but in addition have in the last 25 to 30 years been required to meet the demands of a vastly changing market. To explain this statement, I am sure many of you can remember 30 to 40 years back when most homes were heated by coal furnaces or stoves and shudder to recall the shoveling of coal into the fire and the carrying out of ashes with the attendent manual labor dust. Now this space heating portion of our sales has almost become non-existant due to an almost universal switch from coal to natural gas, oil, and electric heating. Actual figures show a decrease from 119 million to less than 28 million tons per year in less than a twenty year span. Also, most of you can remember the coal burning steam locomotives and the tremendous volume of coal they consumed and then the very rapid change to the diesel-electric locomotives, incorporating improved large diesel engines driving D C generators and electric drive motors, which resulted in cheaper motive power. This change over was so complete that the annual tonnage of coal dropped from 125 million to less than 2 million tons in 15 years. 'Actually, now it requires some considerable interrogation and traveling to find a locomotive still operating on steam.

Jan 1, 1968

By J. J. Zaluski

The Surface Mining control and Reclamation Act (public Law 95-87) (here-inafter the "Act" or "SMCRA") passed by congress in August of 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines, and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations.

Jan 1, 1992

By Adrian C. Dorenfeld

The concentrator of Bonneville Ltd.* at Wendover, Utah, processes a feed obtained by, solar evaporation of a brine containing sodium and potassium chlorides with minor amounts of impurities. Salable potassium chloride concentrateis produced from this feed in two steps: flotation with amine reagents to concentrate the potassium chloride, and washing of the concentrate with fresh water to reach final grade. In the flotation step emphasis is placed on recovery, whereas the washing step has as its objective the production of salable grade (in excess of 60 percent K20 equivalent), with recovery being important but secondary Ideally, flotation should give maximum recovery at a concentrate grade which will permit washing to salable grade with a minimum recovery loss, thereby maximizing over-all recovery. Except for this relationship, flotation and washing are two separate and distinct operations.

Jan 1, 1965

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

By D. Jacobson

There are many different machine design parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the speed at which the cone gyrates. In June 2012, pilot tests were conducted to determine the production and operating conditions over a wide spectrum of speeds. mining operations will have variations in the ore characteristics and feed rates that result in non optimal use of the crushing energy and inconsistent process control. This study documents the measured variation in production and energy efficiency with two operating modes. Overall, the results match the theory, and the capacity and power fluctuated by 25% and 17%, respectively, when operated at full capacity, with an overall trend of slightly coarser discharge size distribution as the speed decreased. Using a fixed feed rate, the crushers had 4-14% higher production when operating at the optimal speed. Secondary analysis showed that the power draw consistency and magnitude of power spikes could also be improved by optimizing the cone speed. Varying the speed of the crusher can be used to tune the crusher during commissioning, adapt to changing ore conditions over long periods of time or be used as a dynamic input into an advanced control system. each action above would serve to make the crusher(s) more productive, more energy efficient, impove process control and would also have mechanical benefits for the machine

Dec 1, 2013

By Nilufer Kursunoglu

Despite being crucial for meeting the world’s energy demands, coal mining operations present considerable health risks, especially when it comes to exposure to coal dust. Longwall coal mining, an advanced technique, has considerably enhanced production but made dust control more difficult. Due to its explosive nature, coal dust continues to be a serious and dangerous concern in the industry despite developments in safety technology. This study aims to comprehensively assess the risk of coal dust explosions by integrating fuzzy risk matrix and Pareto analysis methodologies, offering precise risk ratings for various root causes. A fuzzy risk matrix was developed to assign exact risk ratings to identified root causes. Additionally, a Pareto chart was used to identify the main reasons and suggest particular preventive measures. 17 significant causes were determined for underground coal mines based on the study’s methodology, and some preventive measures were suggested. In accordance with fuzzy risk rating values, root causes were divided into six categories. The root hazard with the highest risk rating was identified as ‘accumulation of inflammable gas/gases’. The proposed approach was used to examine incidents caused by coal dust explosions in Turkish coal mines in order to demonstrate the effectiveness of combining the fuzzy risk matrix and Pareto analysis for assessing coal dust explosions. This study gives not only a solid framework for risk assessment but also critical information for classifying the risks associated with coal mine dust explosions. The results highlight the critical necessity for proactive and preventive actions to reduce the hazards of coal dust explosions and protect the safety of mining workers.

Nov 16, 2023

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The history of Duluth commences with Daniel de Greysolon du Lhut, one of the explorers of the Upper Mississippi who came to the head of the lakes in the summer of 1679. Radisson and Groseillier, and Claude Allouez, a Jesuit priest, are supposed to have visited the head of the lakes, -but there is no authentic record previous to that of du Lhut.In 1792, the fur traders established a fort at Fond du Lac, fifteen miles up the St. Louis River from Lake Superior, but within the limits of the present city •of Duluth. In the early 50's, there were a few scattering settlers at Oneota and around the George Stuntz trading post on Minnesota point. In 1855-6, the settlement on Minnesota point was called Duluth, commemorating the name du Lhut, and organized as a town in 1857. The first board of trustees and town council consisted of -William Nettleton, J. B. Culver; Robert E. Jefferson, Grin W. Rice and William Old: In 1870, the city of Duluth was incorporated, and five years later a portion of the same territory was incorporated as the village of Duluth, and the two municipal corporations were still in existence on March 1, 1887, when the city and the village of Duluth were incorporated as the present city.The first saw mill in Duluth was erected in 1856-57, on the present site of the ship canal. It cut logs from a virgin forest at the upper end of Minnesota point.The first railroad was built to the head of the lakes in 1870. The charter for this road had been granted in 1861 to the Lake Superior and Mississippi Railroad Company, afterward called the St. Paul and Duluth, and which is now a part of the Northern Pacific Railroad."

Jan 1, 1920

By J. P. Matoney

The operation of a modern coal preparation plant, particularly in western Canada, is a very complex task. Most western Canadian operations are processing two or more, sometimes up to ten, different seams through the same plant. This requires a sophisticated multi-circuit plant that needs close operational control. Add the soft nature and large amounts of natural fines of western Canadian coal and you have a formidable cleaning task. To assist in the operation, programmable controllers and sophisticated control concepts are being more widely used. Two of the newest coal preparation plants in Canada have been designed by Raymond Kaiser Engineers Inc. and its Canadian subsidiary, Phillips Barratt Kaiser Engineering, Ltd. The use of programmable controllers and control systems will be illustrated by showing their application in a "typical" western Canadian coal plant. This example will cover flowsheet design, control concept systems application, and possible future uses.

Jan 1, 1983

By Alexander Sutulov

1. INTRODUCTION According to the classical economic approach of the open market economy, copper supply should be regulated by market forces which are (a) demand and (b) prices. In fact, demand is of primordial importance because prices are a reflection of supply-demand balance: they go up in times of shortages of supply and down when over-supply situation exists. In the past few years, this basic mechanism of market economy has been under pressure from a number of non-market forces, such as social and monetary problems of sane important copper producing countries; structural changes in copper mining companies through mergers with oil companies; and other factors which greatly contributed to distortion of the basic supply-¬demand equation. As a result, we have faced in the last three years a situation of oversupply rarely seen in the past, with a catastrophic fall in copper prices, huge losses at mines and unprecedented indebtedness of copper producers. This has deep repercussions in the copper business and its future supply outlook. This is particularly so when taking into consideration that high indebtedness and high interest rates conspire against the very survival of some traditional producers. As we write this comment (July of 1985), close to one half of U.S. copper production capacity is closed down, sane of it for good, while the same precarious situation exists in Canada, Australia, Zambia, and some other primary producers who cannot face present low prices with equally low costs. The question is then what this situation means for the medium-¬term future, until the end of this decade, Particularly when taking into consideration the fact that some of the factors influencing it are of a long-term character. 2. SUPPLY-DEMAND SITUATION IN THE LAST FIVE YEARS Since the last boon year, in 1979, when world copper consumption reached a record of 9.8 million metric tons of refined copper, demand dropped to only 9.0 million tons in 1982, when the crisis bottomed out, and then steadily recovered to the level of 9.7 million tons in 1984. Meanwhile, copper production, which in 1979 was only 9.4 million tons, in spite of the fall in demand, grew to 9.7 million tons in 1981 and 1983 and only temporarily was cut to 9.4 million tons in 1982 and to 9.5 million tons in 1984. As a result of this imbalance, hugh copper stocks were accumulated with supply systematically out¬growing demand by over 2 million tons at one time. With the Western World refined copper demand running at an average of 115,000 tons per week, this oversupply was equivalent to between 15 and 18 weeks production, i.e. twice as large as normal. This was immediately reflected in very low copper prices. Another contributing factor to relatively low copper prices was the lack of speculator interest for this commodity. Between 1981 and 1984 the world experienced a very intensive period of wealth distribution, high interest rates and intensive restructuring off world economy and its industrial sector. Therefore, much of the available money was attracted to more lucrative and attractive investments rather than to the lack-luster performance of copper, and for that matter, of the metal sector in general. The much announced and discussed recovery of the U.S. economy since 1983, and particularly in 1984, with an overall growth of the GNP by 6.8% in 1984, happened to be more oriented to the service sector than the industrial sector and therefore this recovery was not adequately reflected in copper consumption nor to metals in general. This put serious doubts about the future demand for copper. Consequently copper prices failed to improve in spite of an apparent fall in stocks and a healthy increase in the demand for copper since 1982. At the time of this writing (July, 1985), although same analysts claim that the available stocks are running at about 8 weeks of supply, which are considered to be below normal, copper prices are still very low at between 65 and 67 cents per pound of copper. Part of the answer may be the normal seasonal slow-down period in the Northern Hemisphere due to summer vacations and

Jan 1, 1986

By Norman Miskelly

Substantial progress has been made over the last ten years in the development of uniform national and international standards covering the definition, estimation and public reporting of mineral resources and mineral reserves. Agreement between the major participating countries has been reached, which include the requirement that a Competent Person prepares and approves publication of mineral resources and reserves. Most national regulatory organizations have accepted the new standards and have included them in the rules that must be followed by mining companies operating under their jurisdiction. These developments are the result of a concerted effort on the part of professional societies, national regulatory agencies, international organizations, and many dedicated individuals. The historical development of these standards is summarized in this paper. Accepted definitions of mineral resources and mineral reserves are discussed, as well as the definition and role of the Competent Person. Additional effort is needed before the international standards are fully understood, accepted and followed by mining companies, regulatory agencies, the investment community and the general public. Steps being taken toward development of a Mineral Reserves International Reporting Code Template (International Template) that will be available for all countries to use in deriving their specific country reporting codes, are outlined

Jan 1, 2003

By Lorraine B. Burgin

The extensive lead time to develop most Arizona copper deposits commenced with initial production efforts before the turn of the century, when the first attempts were made to recover gold and silver and later copper from the high-grade vein deposits of the territory. Each of these discoveries, prospects, and early operations had its own lead time and life cycle as economic production was attempted. Because prices of the metals fluctuated and the higher grade material was depleted, economics forced operations to close and companies to fail. Renewed interest in the property because of improved conditions, different interpretation of the geologic structure, or new promotional ability frequently resulted in the formation of yet another company to finance the exploration and, hopefully, the development of the property. This cycle of renewed activity and subsequent abandonment was and is common, accounting for many lead times and for the long period of time from the initial location of claims to large-scale production. In order to gain a perspective on the lead-time interval necessary to achieve development of a large-scale operation, the histories of several major Arizona mines were examined, rather than a simple listing of discovery and production dates of many mines to arrive at a statistical average. The Miami, Castle Dome, Copper Cities, San Manuel, and Twin Buttes properties were studied, and as much data as possible obtained on the Pinto Valley, Esperanza, Sierrita, Pima, and Mineral Park-Ithaca Peak properties.

Jan 1, 1974

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By C. M. Brown

The semi-autogenous grinding circuit at the Utah Mines Limited, Island Copper Operation, located on Vancouver Island, British Columbia, is described. Since start-up of the operation in 1971 grinding circuit throughput has been progressively increased from the initial design rate of 30,000 to the current average 45,000 tonnes per day (t/d) of porphyry copper ore. Key developments and modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1985

By Jeff Salai

The CP-3A contract is the final segment of the MWWST’s 28.3 km (17.6 mile)pressurized water supply tunnel for the metropolitan Boston area. The 1,288 m (4,226 feet) of U-shaped tunnel alignment passed through five rock zones employing four different primary support systems. The short tunnel began in Weston, Massachusetts, at Shaft 5A in soft, completely weathered argillite, passed through a fault zone, and ended in Dedham granite. An 18-foot diameter horseshoe starter tunnel was built to accommodate a 4.94 m (16-foot 2 1 / 2 inch) diameter Robbins TBM. Heavy water inflows were anticipated and subsequently encountered during probe drilling. Pre-excavation grouting was implemented at high pressures to displace high water inflows in the starter tunnel and consolidate the fault zone. This paper will provide an overview of the tunnel construction with an emphasis on ground control, grouting and survey control.

Jan 1, 2001

By Stewart W. Daniel

Competitive pressures involving product duality, uniformity and economics are increasing the interest in and accelerating' the adoption of automation by the cement industry. The demands of this industry on instrumentation and control manufacturers for more effective and reliable control of process variables is also increasing. The trend to replacing small grinding mills with a fewer number of larger mills is lowering the investment requirement per unit of capacity both for the mills and for their automation. Cement process control systems of today are more sophisticated than the equipment installed two or three years ago, not because the process itself is more complex but because todays demands require a higher degree of control action and accuracy. Because of increasing labor costs, an important objective of an automation program is a reduction in the process labor content. This can be realized by allowing the operator free time for other duties, by increasing the number of grinding circuits one operator can supervise and by removing to. a large extent the need for the operator to make process' adjustment decisions.

Jan 1, 1965

By D. W. McGlashan

[Becaune ad ;the extennive nwrgace anea od u.X chopRex2 in emmiom, emuhion dRokdtiun oddeh poaaibWa don ;the necove/ry ul; BinQey divided minmcd pa~LL&a, Swr~aC;tavu% mu2 akab&ze ;the emu-bion and poan an an ad~i&y don ;the dahed mina&. OZhm hpohtant acto oh me ;the naAwre od ;the em&iun inghedied, ;the nQRaLLve volwna 06 the colz;tinuoun and dincon;tinuoun phaa, ;the change aign bonne by the dnuplm ad the o.X phae, ;the z&a pu;tenticd od ;the dahed minmd, the ~olubRe am curdent 06 khe wcr;ten-pulped and gnuund onu. AX on nem ;the AoQRec;trtic point on ZPC, ;the doubRe Raym about ;the minW-&den oil dnopR& i~ neduced in ;tkichnaa and the dn_opR& wU codace and continue to aggnegate into agglommaka . Invetmion dnom O/U ko W/O can UCCWL depending upon a nwnbm a 6 in;tmQeaked daotuh~. EReothokin&Lc inn&wnenta;t/iun to meanwre ;the ZPC, QReckProphonQkic mobilXty z&a pokeW and hakerning cuttrtent me invcduabte in ;the appficatiun ud emu-bion dRo;tat;iun ;to m&~c and nonm&~c minu.&. ] INTRODUCTION Recent interest in emulsion flotation can be ascribed to the necessity of selective separation and concentration of extremely fine minerals. That which follows is an elucidation of the many factors-in emulsion technology in application. In applied surface chemistry for solid-particulate separation and concentration, emulsion flotation is one of the intermediate processes between froth flotation, in which the continuous phase is water (99.5 to 99.999% by volume), and particulate extraction, in which the continuous phase is almost entirely an organic-fluid. Another intermediate process is particulate exchange (or partition) in which immiscible or very limitedly miscible phases are in controll¬ed but appreciable volumes. Surfactants are common to all of these

Jan 1, 1968