Search Documents

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By R. L. Clayton

The Bagdad district is 67 kilometers west of Prescott, Arizona, (Figure 1). The area north of the Old Dick and Bruce Mines was originally mapped by Anderson, Scholz and Strobell between 1943 and 1945, (1). The region is perhaps better known for the Bagdad porphyry copper deposit of tertiary age. However, 2 to 5 kilometers south of this deposit are several small massive sulfide occurrences in a eugeosynclinal Precambrian greenschist environment. More specifically, in. the Bridle formation of the Yavapai schist series. Three of these mines - Old Dick, Bruce and Copper Queen - were mined by Cyprus Mines Corporation between 1957 and 1977, and produced nearly 2mm tons of 3.6% copper and 12% zinc. These deposits occur at the interface between andesite and rhyolite and are stratiform in character. Certain structural and textural properties of the Bruce orebody suggest that remobilization of the massive sulfides occurred at some period during the metamorphic history of the area.

Jan 1, 1978

Placing a detonating explosive inside a volume of rock is an efficient method of rock fragmentation. The explosion generates internal tensile stresses in the rock, and because rock is a brittle material, this brings about crack propagation and fragmentation far more efficiently than does application of explosive on the surface. To get the explosive inside, we drill a pattern of boreholes and charge the explosive into the holes. This is really the one and only purpose of making blastholes in mining: to give access for the explosive to the interior of the rock. No matter how big and expensive a drilling jumbo we stand up in front of a rock face, and no matter how many boreholes we let it drill, the rock does not fall apart by itself without blasting. It is the action of the explosive in the boreholes that does it. When we consider that we need a pound or two of explosive for every cubic yard of rock to be fragmented, and a pint of borehole volume for each pound of explosive, we see that the process of blasthole charging is an important element in the whole process of rock blasting.

Jan 1, 1975

By M. Hakan Morcali, Onuralp Yücel, Haldun Gürcan, Serdar Aktas, Semih Özbey, Alper Keskin

"This work presents a method for the precipitation of cobalt sulfate by alcohols, specifically ethanol and methanol. The effect of the initial concentration of cobalt, the volumetric ratio of alcohol to cobalt sulfate solution, the addition of sulfuric acid and ammonia, and the effects of common ions on the precipitation percentage were investigated. The performances of ethanol and methanol were compared in terms of the precipitation percentage of cobalt sulfate, and explanations for different performances are offered. In the sulfate-based solution, the alcohol was shown to displace water ligands from the first coordination sphere of the cobalt(II) cations, which led to the precipitation of the cobalt ions as cobalt sulfate heptahydrate. SEM analysis revealed that the particle sizes of the powders produced by this method are smaller than those of commercially available cobalt sulfate. The scientific literature contains no data on the solubility of cobalt sulfate in ethanol. In this study, the solubility product constant (Ksp) for cobalt sulfate was experimentally calculated to be approximately 1.15 x 10-5.IntroductionCobalt sulfate, which is one of the most important compounds of cobalt, is used in the electroplating and electrochemical industries. The addition of cobalt sulfate to nickel-plating baths makes the treated metals brighter, harder, smoother and more ductile (Armstrong et al., 1988). It is also used as a desiccant for lithographic inks, varnishes, paints and linoleum, as well as in storage batteries, e.g., nickel-cadmium (Ni-Cd) and lithium-ion (Li-ion) rechargeable batteries (Kang et al., 2010). Cobalt sulfate is employed as a coloring agent in ceramics, enamels and glazes to prevent discoloration and as a copigment for the decoration of porcelain. In addition, cobalt sulfate has been used in animal feeds as a mineral supplement (Budavari et al., 1996; Kirk and Othmer, 1999).In the past, brewers used cobalt sulfate to prolong the life of beer foam (Kesteloot et al., 1968). Ranchers have dosed livestock with cobalt sulfate or used fertilizer enriched with this mineral to ensure that their animals obtained sufficient amounts of the trace mineral, which is essential to the production of vitamin B12. Cobalt sulfate has also been used in veterinary medication to prevent and treat cobalt deficiency in ruminants, which causes a reduction in feed intake and body weight, accompanied by emaciation, anemia and debility.Cobalt sulfate is a water-soluble bivalent cobalt salt. Cobalt sulfate heptahydrate dehydrates entirely at 420° C, and the dehydrated salt forms red monoclinic crystals."

Jan 1, 2015

By R. W. Leonardson

Tectonic activity in northern New Mexico during late Oligocene and early Miocene time presaged events which led to the development of molybdenite deposits at Questa. East-northeast directed crustal extension produced north-northwest striking tensional fracture systems paralleling the early Rio Grande rift. A sequence of Oligocene andesite flows and breccias is overlain by a thick early Miocene rhyolite ash-flow tuff. Eruption of the tuff initiated collapse of the Questa cauldron: the south margin of which occurs as an east-northeast striking, north-dipping structurally weak zone. Continued east-northeast post-cauldron extension permitted the high level emplacement of granite stocks with coeval rotational deformation of fault blocks composed of cauldron fill and [ ] floor. The stocks occupy north-northwest fracture zones in the south margin of the cauldron, and porphyry dikes occupy east- northeast striking faults that define the south margin. These two fracture systems have played a dominant role in localizing the intrusive porphyries and associated mineral deposits at Questa. A molybdenite-bearing breccia matrix and related stockwork mineralization generally occur within volcanic rocks. Mineral deposits are spatially related to fault zones and the upper con- tact of their source intrusives. Deposits are localized in fault zones up to several thousand feet long and 100 to 500 feet in diameter. Magmatic-hydrothermal solutions from the source aplite porphyries have produced potash metasomatic alteration which is strongly centered on the mineral and ore zones. Alteration in ore is represented by orthoclase, quartz and secondary biotite. This pattern grades into secondary biotite and propylitic zones forming successively weaker alteration assemblages away from ore. Younger phyllic and argillic assemblages are particularly widespread only where strong north-northwest extensional fracture zones cross the south cauldron margin.

Jan 1, 2013

By Qingwen Shi, Gang Xu, Shuwen Wang, Brijes Mishra

Pressure relief borehole is one of the most effective methods to treat coal burst in deep-buried coal seams. However, due to the large amount of randomly distributed fractures in the coal body and the varying stress environments in underground coal mines, there is no practical method to assess relief boreholes by far, which brings problems for borehole design and construction. This study focuses on the assessment of relief boreholes in a single driving entry wherein the impact of mining panels on relief boreholes is eliminated. A practical method, focusing on field monitoring of borehole deformation with a new device, is developed to evaluate the single driving entry’s relief boreholes. This method is applied to a Chinese coal mine. The application results showed that the convergence process of the boreholes showed a three-phase characteristic. Phase one involves the fastest deformation, reaching up to 8% in the first 3 to 4 days. Phase two lasts longer and converges more, reaching up to 30% in 4 months. Phase three stays balanced until the excavating face moves. The three-phase characteristic indicates that a large diameter of the borehole ensures relief efficiency because the borehole provides adequate space for deformation throughout its life span. In addition, it is verified that long boreholes and slow footage improve relief efficiency by providing adequate time for the boreholes to work. The application proposes that boreholes in the test coal mine need to be drilled larger and longer for optimization.

Oct 19, 2021

By Karoly (Charles) Kocsis, Kyle A. Scalise

Understanding the climatic conditions in underground mines is necessary for efficient ventilation design, cost savings, and to ensure the health and safety of mine workers. Large volumes of ventilation and climatic data including air volume, barometric pressure, dry bulb temperature, and relative humidity were collected at active underground precious metal mines in Nevada, which allows for the determination of wet bulb temperature and other key parameters. Through the utilization of neural networks, the wet bulb temperature at the bottom of the intake shafts is predicted, while taking into account the “thermal flywheel effect” (TFE). Wet bulb temperature is one of the most important climatic parameters to model and understand because it significantly affects the work conditions and the cooling capacity of the ventilating air. The accurate prediction of the dry bulb and the wet bulb temperatures at the bottom of intake shafts is critical when assessing the climatic conditions in future underground mines and deciding onwhether a cooling system is needed to assure adequate working conditions throughout themine. By utilizing accurate predictions of wet bulb temperatures and other climatic parameters, mine personnel will be safer as reported by Bluhm et al. (2003), and a more accurate ventilation design can be achieved resulting in major cost savings for underground mines.

Mar 3, 2021

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Jan D. Miller, Chen‑Luh Lin

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of cm size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of mm size. Based on Micro-XCT, it was expected that 85% of the copper for sample A could be recovered at 65% of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual energy (DE) X-ray radiography was used as a basis for sorting. Previous DE X-ray radiography of a drill core sample demonstrated that this rapid detection method can be used to identify rich or poor Cu-bearing coarse particles. Pilot scale X-ray sorting of sample A (10 × 1 cm) showed 31% rejection of a 0.08% Cu gangue product with a corresponding recovery of 90% copper.

Nov 30, 2021

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By Michael Markels

The United States Environmental Protection Agency (EPA) is charged under the Federal Water Pollution Control Act Amendments of 1972 with establishing effluent limitations which must be achieved by point sources of discharge into the navigable water of the United States. Section 301 (b) of the Act requires the achievement by not later than July 1, 1977, of effluent limitations for point sources, other than publicly owned treatment works, which are based on the application of the best practicable control technology currently available as defined by the Administrator pursuant to Section 304(b) of the Act. Section 301(b) also requires the achievement by not later than July 1, 1983, of effluent limitations for point sources, other than publicly owned treatment works which are based on the application of the best available technology economically achievable which will result in reasonable further progress toward the national goal of eliminating the discharge of all pollutants, as determined in accordance with regulations issued by the Administrator pursuant to Section 304(b) to the Act. Section 306 of the Act requires the achievement by new sources of a Federal standard of performance providing for the control of the discharge of pollutants which reflects the greatest degree of effluent reduction which the Administrator determines to be achievable through the application of the best available demonstrated control technology, processes, operating methods, or other alternatives, including, where practicable, a standard permitting no discharge of pollutants.

Jan 1, 1975

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By M. A. Anderson

After mope than fifty years Of Continuous operation, the Nevada Mines Division found itself faced with declining ore headings and metallurgical efficiencies, and rising operating costs. Although intensive process improvement programs had been initiated at various times in its history, insufficient return on investment served to defeat plans for any major changes in circuitry. The advent of practical large-volume flotation machinery, along with the success of long-range exploration drilling programs, complimented the results of an intensive program of research and development. The result of laboratory testing, pilot plant testing, and full scale plant tests was the proven indication of metallurgical improvement given increased flotation residence time and the effect of mechanical agitation in flotation.

Jan 1, 1975

By D. E. L. Zapata, O. J. R. Baena

"INTRODUCTION Mining is a fundamental part of the historical and economic development of a country. In Colombia, this is reflected from pre-Columbian jewelery, to being now one of the first exporters of coal worldwide, in 2017, the Colombian mining sector contributed approximately 6% of GDP (Ministerio de Minas y Energía, 2017). Coal, nickel, gold, platinum, emeralds, limestone, salt, phosphate rock, clays, siliceous sands and to a lesser extent copper, manganese, magnesite, barite, gypsum and various types of ornamental rocks, among others are produced (UPME, 2016). The contributions of mining activity in the economic dimension is more measurable, on the contrary in other dimensions, as the social and environmental, for this, every day there are new proposals and tools oriented to strengthen how to evaluate the contributions in terms of the sustainability and responsibility, with the aim of quantifying, concreting and non-utopian, to improve the life quality of a community and not only to comply with reporting and gaining prestige. Colombia has a generalized increase in the mining sector where the levels of informality and illegality are evident only 10% of mining activity is legal (UPME, 2014), also, the mining sector is accused of human rights violations, high levels of inequality, poverty and the affectation of ecosystems due to bad environmental management, among other situations (ACNUDH Colombia, 2015). This problem has generated rejection to the realization of the mining activity in many places of Colombia. At this point, it is important to clarify this problem is more complex, different actors are involved in this conflict, but it is an evidence that is needed a sustainability model for specific realities such as the Colombian mining. This situation in the current mining activity, is similar to the chemical industry situation three decades ago, because of an extensive problem in relation to repeated work accidents, natural disasters and indications as a highly polluting and unsustainable industry, with the aim of improving, not only this public perception, but also in the way of carrying out the business activity. Thus, in 1985, the Canadian Chemical Producers Association released the Responsible Care Program (RCP) (ICCA, 2015). Being aware that companies were responsible for the affected lives in some way by the operation and needed to improve workers safety, environmental protection and most importantly how legal persons should comply with the law, but go beyond this. RCP is most recognized sustainability initiative in the chemical sector, companies associated are recognized for having high quality standards, continuous improvement, visibility, corporate ethics, environmental and social management (ACC, 2015). In addition, to meeting the objectives is set out the creation of a model that increasing reputational sector levels. This initiative is considered to be a worldwide successful case of reporting corporate responsibility indicators and contributions to sustainability from the industry sector to local development (BASF Group, 2016)."

Jan 1, 2018

By Ted Budd, Vladimir Goubanov

The East Central Interceptor Sewer, commonly known as the ECIS Project, is the largest public works construction project awarded by the City of Los Angeles. The complexity of this $240 million project, together with the challenge created by the mandated 1,000 calendar days for construction completion, make this project a major interest for the tunneling industry. This paper will describe the ECIS tunnel project, currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor / Frontier-Kemper. Mining of the18.5 km (about 11 miles) long and 4.7 m (15ft-4in) diameter tunnel is underway with four Tunnel Boring Machines mining at the same time. Details on the mining machines, muck handling systems, innovative construction sequence, together with mining progress will be given.

Jan 1, 2003

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

Following the recession of 2001, restrained consumer spending, declines in domestic manufacturing and industrial output, and increased unemployment led to a lack-luster year in the domestic economy. In 2002, the U.S. real gross domestic product (GPD) grew only 2.4%. Significant production declines in the U.S. metals industry were registered by copper, lead and zinc producers. Steel producers, despite a slight improvement in shipments, continued to face strong foreign competition, higher energy costs and lower prices for their products. Homebuilding and other domestic construction sectors— major consumers of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above 2001 levels. A strong U.S. dollar relative to other national currencies continued to weaken the competitive stance of U.S. metal and non-metal mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2003

By A. W. Khair

In 1985, an extensive longwall mining research project was initiated by the West Virginia University Research Center entitled "An Improved Longwall Mining Technique" with the purpose of providing operational guidelines for the mining industry to enable efficient operation of its existing and projected longwall installations. One task involved in this extensive research project was monitoring ground movements due to longwall mining and evaluating their impact on surface and subsurface structures. This paper presents an analysis of the effects of topography on quasi-static and dynamic ground movements and the severity of damage inflicted on surface structures. The site was chosen for the study with an attempt to obtain a representative account of the topography experienced in the Northern Appalachian region, and more importantly to contain a substantial number of varying topographical features i.e., mountains, hillsides, valleys, and flat bottom land. The study was made possible by typical subsidence monitoring technqiues, however subsidence monuments were surveyed on a frequent basis, intermittently during face advancement. Ground movements were investigated under both quasi-static and dynamic conditions. This provided insight into the propagation of subsidence and the dynamic affects it has upon surface structures.

Jan 1, 1987

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By Steve Kral

In December 2013, the Colorado Department of Transportation (CDOT) completed the widening of the eastbound tunnel on Interstate 70 (I-70) from two lanes to three. Work on the westbound tunnel began earlier this year and is scheduled for completion in December. The Twin Tunnels project is located in the mountains about 55 km (35 miles) west of Denver. They were bored during the 1960s when I-70 was being built and became the main access to Colorado?s growing number of ski areas and the state?s Western Slope. Throughout the decades following their construction, traffic on I-70 continued to increase and now the tunnels have a major bottleneck. Com-mutes to and from the mountain resorts, particularly on weekends, have become long and slow. Adding a third lane through the tunnels will help alleviate the congestion. (A complete report on the project can be found in T&UC, December 2013, page 61.) Once the eastbound tunnel was completed late last year, CDOT authorized the funding to begin work on the westbound side. That made economic sense, as the equipment used on the eastbound tunnel needed to only be shifted across I-70 to begin work on the westbound side, rather than removing it in December and bringing it back in March when construction began on the westbound tunnel. Work on the westbound tunnel uses essentially the methods that were used on the eastbound tunnel ? removal of the existing concrete lining and using drill-and-blast methods for tunneling widening. The main difference between the two tunnels is that the westbound side requires more blasting on both ends to widen I-70 to three lanes.