Search Documents

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By G. G. Marino, J. W. Mahar

This paper provides an utierstanding of the betivior and potenttil damage of homes resulting from sag-type mine subsidence. This is done with extemive research of numerom case histories in Illinois collected by the authors. The howe response to substience-itiuced ground displacements are summarized and evaluuted. A damage level criteriu, specifically developed for residenttil structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 9, 1985

By T. W. Camm

Some of the defining characteristics of narcissists include a grandiose sense of self-importance, preoccupation with success and power, a sense of infallibility, and a supreme confidence in their ability and intelligence. Ironically, many of these characteristics are rewarded in business organizations, which may explain why there seems to be so many narcissists in management positions. Assuming we will be dealing with narcissists throughout our career, it makes sense for us to understand what makes them tick, and more importantly what we can do to work with them in a constructive manner.

Feb 23, 2014

By Philip A. Bucci

The Florida phosphate industry successfully uses froth flotation to concentrate phosphate in: the particle size range of approximately 28 to 150 mesh. However, as recently as 1965, coarse particles in the range of 14 to 28 mesh generally had not been beneficiated by conventional flotation methods at recoveries high enough to be considered adequate. It has been customary to upgrade this coarse material; by "agglomerate flotation" or "skin flotation" using belts, tables or spirals. While these devices have proved commercially effective, their capacities are much lower than those of froth flotation cells. To determine whether coarse phosphate material could be recovered successfully by froth flotation, Armour Agricultural Chemical Company began a series of pilot and plant tests; in April 1965. Objective of the tests was to compare over-all performance of a froth flotation cell design relatively new to the phosphate industry with results from the belt circuit at the Bartow, Fla., plant.

Jan 1, 1966

By T. O. Llewellyn

The Bureau of Mines, U.S. Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8 to 10.2 percent P205 and 1.7 to 1.8 percent MgO. Chemical analyses of sized fractions indicated that no pebble concentrate (plus 1.2 mm) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid-fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0 to 31.3 percent P205 at flotation recoveries ranging from 72.4 to 96.1 percent of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36 percent. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3 percent P205 and 0.55 percent MgO could be produced with a flotation recovery of 89.9 percent. The MgO content of concentrates obtained from the Manatee No. I and Hardee samples was 1.20 to 1.36 percent, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 percent, but with a concomitant loss in phosphate recovery.

Jan 1, 1983

By Paul D. Bybee

The Freeport Sulphur Company operates four sulphur mines in the coastal marsh area-03 South Louisiana. Employing the Frasch process of mining, approximately 13-million gallons of water per day is heated to a mining temperature of 325°F and is injected into the sulphur bearing formations of the four mines. A volume of cold waste water, roughly equal to the Input, is removed from the formations and presents a disposal problem. Two additional mines are currently being developed and will increase the disposal volume by an additional 5-million gallons per day. Although these properties are in a relatively small area, geographically speaking, as shown in Figure 1, they each represent a separate disposal problem with the treatment methods designed for the individual mine.

Jan 1, 1959

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By C. Webb, M. A. Tuck

This paper describes the application of a cable disc elevator to continuous lift ore vertically from underground mines. Application of this system requires the tensions developed within the cable must remain within the carrying capacity of the cable including applicable safety margins. A critical element occurs at starting the system when it is fully loaded which requires the force developed by the system to exceed the static friction forces. This paper describes the laboratory rig developed to investigate the static friction forces. Details of the results of tests on three different ores for both dry and wet conditions are given. These results are discussed.

Nov 19, 2020

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By M. Adnan Göksel

Pyrite cinder is generated by roasting pyrite for sulfur dioxide production. It contains up to 62% iron, but also may contain other hazardous or toxic materials such as Zn, Pb, As, T1, Cd, Cu, Sn and S. Furthermore, the physical characteristics are not properly suited for conventional sintering. As a result pyrite cinder is considered to be unsuitable for iron and steelmaking or for outside storage because of its potential for causing environmental problems. In recent years industrialized nations have put increasing pressure on the manufacturers to either use such waste products or properly dispose of them. In this study, solutions to both the iron recovery and disposal problem were attempted by pelletizing the pyrite fines with internal carbon. The pellets, after hydrothermal hardening, were reduced and melted in a furnace for hot metal production. Hot metal of usuable quality was produced and the hazardous materials were either collected with the fumes or in the slag.

Jan 1, 1984

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand's approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By Armine F. Banfield

The Purpose of the Paper It is fitting that the first paper of a session on the Financial Aspects of Mining should be on the basic data upon which any financial discussion of a mining project must be based. The history of a mining project starts with exploration in an area considered geologically favorable for mineralization and culminates in the discovery of a body of valuable mineral material commonly known as a mineral deposit. Subsequently more detailed exploration establishes the approximate size, shape, tonnage and average grade of the deposit by surface and/or underground drilling, -surface trenching and/or underground workings. Some preliminary metallurgical testing and other studies, as required, are made at this time. Development work is then carried out to provide representative samples for determining flowsheet and metallurgical balances, preparing the deposit for production and establishing more firmly the grade and mining characteristics of the deposit. A feasibility study is then made of the engineering aspects of the project including the estimation of operating coats, the capital required to place the deposit into production, profit and return on investment. A valuation of the deposit

Jan 1, 1972

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By Paul H. Johnson

Heap leaching is a simple means of recovering copper from oxide and oxide-sulfide ores. Although this method requires relatively low capital investment, it suffers from low copper recoveries and relatively high acid consumption. The objectives of this study were (1) to determine what factors influence these shortcomings, and (2) to establish a basis of correlation. between laboratory and field testing. The principal methods of leaching copper ores at the present time are heap, dump, in-place, and vat. A number of references are presented in the bibliography on the theoretical and practical aspects of these methods. In the heap-leaching method, crushed or uncrushed oxidized copper ore is placed on a prepared drainage pad. Acid leach solutions are dis¬tributed over the top of the heap, caused to percolate downward through the ore bed by gravity, and are drained from its base. The leach duration is generally a matter of a few months. Dump leaching is used to recover copper from very low-grade oxide-sulfide pit-waste materials. Here again, leach solutions are, percolated downward through a heap. However, in this method, little or no acid is added to the leach liquors, prepared drainage pads are not used and the leaching cycle is generally measured in terms of several years. Leaching agents are usually autogenously generated by the breakdown of sulfide minerals within the dump.

Jan 1, 1970

By J. C. Norman

The United States was the world’s largest producer and consumer of boron compounds during 1995. According to estimates from the US Geological Survey(USGS), boron mineral concentrate and chemical production in the United States totaled an estimated 1.1 Mt(1.2 million st) yielding 602 kt (663,000 st) of B2O3 for an estimated value of $462 million. This level of production exceeded 1994 revised production figures by about 9%. The United States continued to provide nearly all its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. During 1995, about 900 people worked in domestic boron mines and plants, about the same as in1994. USGS estimated total world production of boron during 1995 to be about 3 Mt (3.3 million st), yielding about 1.6 Mt (1.8 million st) of B2O3. World production in 1995 was about equal to revised 1994 levels.

Jan 1, 1996