Search Documents

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2001

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Junior S.J. Ramokgopa Immediate Past President J.R. Dixon Honorary Treasurer J.A. Cruise [ ] Annual report In accordance with the current management policy, this report on the activities of the Institute is presented under eight main headings: 1. Interests of Individual Members 2. Technical Meetings 3. Publications 4. Regional Development 5. Engineering Science and Technology in South Africa 6. International Liaison 7. State Liaison 8. Management and Administration.

Jan 1, 2001

By N. Kornelius

In recent years there has been an increased focus on corporate governance matters worldwide. The duties and responsibilities of directors of companies have come under close scrutiny, with shareholders increasing their demands for greater responsibility and accountability. Media attention and pressure groups have also had their effect. Governmental actions have supported these demands and directors have witnessed sweeping legislative changes imposing more onerous duties and liabilities than formerly imposed upon them at common law and in terms of the Companies Act. At the same time, the power of regulatory bodies has been increased to enforce this legislation and make someone pay to remedy an alleged infringement. Breach of such duties may incur personal or criminal liability, or both. Environmental protection legislation has become a particularly prevalent feature in this regard, and the number and complexity of statutes concerning the environment have increased over the past few years. Directors of South African companies will be familiar with relevant acts such as the National Environmental Management Act 107 of 1998; Conservation of Agricultural Resources Act 43 of 1983;Hazardous Substances Act 15 of 1973, as well as the National Water Act 36 of 1998. Now the directors of mining companies are faced with the Mineral and Petroleum Resources Development Act 28 of 2002.

Jan 1, 2003

By S. Sun

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest is reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi-component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By M. Vandewalle

What separates the support of mining openings from the support of similar civil engineering structures is the fact that mine openings have to survive large deformations as a result of changing stress conditions induced by progressive mining. Steel fibres impart to concrete and shotcrete a high degree of ductility which not only allows the shotcrete and concrete linings to absorb important rock movements but also to increase its bearing capacity by a redistribution of the loads. A range of applications will be discussed technically and economically.

Jan 1, 1998

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004

By L. C. Stilwell

Input-output analysis is a major branch of quantitative economics, and is used to analyse the flow of goods and services between production sectors in a national economy. Its purpose is to determine the relative value-adding capacity of each sector. The model has also, in recent years, found increasing use in assessing the environmental and ecological impact of development projects. It has, however, never been applied to individual production facilities, such as large mines, which themselves have complex economic structures, through which there is a flow of goods and services. Conventional cost and accounting systems, as used on mines, treat production sectors as separate cost centres, and do not determine the inter-relationships between them. This can lead to incorrect conclusions on the relative value of sectors and their impact on the total economic performance of the facility. This paper explains the basic principles of input-output analysis, and presents an example of its application to a simplistic model of a mine, which is used in the absence of any real data. The paper concludes that, by forcing definition of the value adding function of each sector, input output analysis will facilitate control of inputs, or costs. This will result in optimal application of resources and exploitation of ore reserves. The authors realise the model needs to be tested on an operating mine, and hope this paper will result in an opportunity to do so. The authors wish to thank the anonymous referees for their valuable comments.

Jan 1, 2000

By T. Nishimura, H. Kiyama, K. Wakimoto

Discussion on the load bearing capacity of ground and the stability of tunnel is presented. We derive a simplified solution of a circular lined-tunnel in an elastic ground. The solution results in a better understanding of characteristic curves. Use of DEM allows us to consider effects of possible yield of the overstressed zone around the tunnel and inherent discontinuity of ground on the curves. Diskussion auf der Last Tragfähigkeit Bodens und die Stabilität des Tunnels wird dargestellt. Wir leiten eine vereinfachte Lösung eines kreisförmigen Ausbautunnels in einem elastischen Boden ab. Die Lösung ergibt ein besseres Verständnis der Kennlinien. Um Gebrauch DEM erlaubt uns, zu betrachten Effekte des möglichen Ergebnisses der überbetonten Zone den Tunnel und zugehörige Unstimmigkeit des Bodens auf den Kurven. La discussion sur la portance de charge de la terre et de la stabilité du tunnel est présentée. Nous dérivons une solution simplifiée d'un revêtement-tunnel circulaire dans une terre élastique. La solution a comme conséquence une meilleure compréhension des courbes caractéristiques. L'utilisation de DEM nous permet de considérer des effets du rendement possible de la zone surchargée autour du tunnel et de la discontinuité inhérente de la terre sur les courbes.

Jan 1, 2003

By M. A. Amarante

Beneficiation studies were conducted on a Portuguese feldspar ore, in order to obtain final products capable of being used in the ceramic industry. A simple scrubbing operation is enough to break the lumps in the feed. The ore deposit contains ca 35 x 106tonnesfrom which, by screening, three main products could be obtained. This paper focuses on the beneficiation of the 500/74 µm fraction, which constitutes about 27% of the ore, assaying 9.42% Al2O3,equivalent to approximately ca 46% feldspar, with a mean iron content of 0.29% iron oxides. Magnetic separation and froth flotation testwork was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron content of the feed to values between 0.04 and 0.08% iron oxides with an average yield greater than 90%. Flotation with HF, provided a feldspar recovery of 45?46% with a concentrate assaying 17.6% Al2O3. The use of H2SO4, gave a recovery of 35?36% of feldspar concentrate, assaying 16.1% Al2O3. However, economic and environmental advantages of using sulphuric acid may compensate for the lower mass recovery. The iron content of0.12% iron oxides in these concentrates, could be reduced to 0.04?0.05%, by further magnetic separation.

Jan 1, 1997

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

The EMEM Awards of the Department of Minerals and Energy (DME) were formally launched on 3 March 2000 by Ms Susan Shabangu, Deputy Minister at the Department?s Mineralia Centre in Pretoria. The launch was attended by invited guests from the mining and aggregate industries ,representatives of the Patron Organisations (see below),non- government and scientific organizations, the media, other government departments involved with mining environmental management and members of staff of the DME both nationally and regionally.

Jan 1, 2000

Work undertaken in the field of cut-off grade optimization has not advanced much beyond the work undertaken by Lane in 1988. His definitive work is based on the calculus of the Net Present Value criterion which is the most widely understood, consistent, and appropriate method by which sequential cash flows arising from the extraction of mineral reserves from an exhaustible resource can be represented. Although the mathematics is not complex Lane’s method is not a widely appreciated or applied approach to maximizing the value of a mining operation through selection and balancing of operational cut-off grades. Three stages in a mining operation namely, mining, processing and marketing were defined by Lane and the economics of each stage are identified and isolated to provide an optimum cut-off for each stage. Points of intersection along the present value curves for each stage of a mining operation are used to identify balancing cut-off grades at points where the capacity of the mining, processing and marketing stages is fully utilized and the Net Present Value of the operation is optimized. Data that simulate a small, deep-level Witwatersrand-type gold mine with an average grade of 6 g/t Au and a logrithmic variance of 1.2,are applied to the model to illustrate the benefits of representing cut-off grades in terms of present value curves for different segments of a mining operation. Keywords: Cut-off grade, Net Present Value, grade-tonnage curve, balancing cut-off grade, mining, processing, marketing.

Jan 1, 2003

By T. E. Pogue

This paper traces the co-operative initiative undertaken by South Africa?s gold mining companies through the Chamber of Mines Research Organization (COMRO) in development of hydraulic technologies. After a brief description of the structure of these technologies? development under COMRO?s stewardship, the paper turns to an overview of the structure of innovation within which these hydraulic technologies were developed. A central focus of this paper is systematic review on whether similar technologies are likely to emerge in the present system of innovation and the role played by innovation policy.

Jan 1, 2006

By J. T. Kalala

Energy consumption and wear of grinding media and liners are the major cost factors in milling plants. Since the beginning of the last century, much effort has been directed at the prediction of the power draw as affected by the mill operating conditions. This paper explores the prediction of the liner wear using the discrete element method (DEM). A mathematical model taking into account adhesion, abrasion and impact wear which occur in dry mills is derived in order to predict the loss of material on liners. The mathematical model is implemented in the DEM code using an objective function in order to produce realistic simulated profiles. Our DEM simulated predictions are compared to published experimental and industrial data. Keywords: modelling; discrete element method; liner wear

Jan 1, 2004

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton's JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton's empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d'évaluer JRC qui est un indice de rugosité superficielle d'une fracture de roche à l'aide du modèle de fracturation, compte tenu de son effet d'échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d'une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l'aide de la formule empirique Barton sur la base des résultats de l'essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d'évaluer l'échelle d'endentement d'une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d'évaluation de JRC par rapport au profil JRC.

Jan 1, 2003