Search Documents

By C. Van Rhee

In dredging practice sand is eroded at very high flow velocities using water jets. The existing pick-up functions overestimate erosion. By taking the permeability into account conventional pick-up functions can be made suitable for high velocity erosion. This can be achieved by modifying the critical Shields parameter. The procedure is demonstrated using the pick-up function of Van Rijn. The theory is compared with experiments and agreement is good.

Jan 1, 2007

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By O. Fenn

Earlier work had shown that the use of water jets at moderate pressure enhances mechanical cutting in hard rock. To assess the potential of this technique for use in conjunction with free-rolling cutters, a series of laboratory tests was conducted with disc and button cutters to determine the effect of variations in the jet and cutting parameters on the cuter performance. In these tests it was found that the use of water jets at pressure in the range 5 to 40 MPa can reduce the forces on a free-rolling cuter by 40 per cent, which represents a significant improvement in cutting performance. The reduction in thrust force was found to be dependent on jet pressure: the greater the pressure, the greater the reduction. The reduction in rolling force was independent of jet pressure over the range investigated. The results indicate that no additional improvements in cutting performance of any significance are to be gained by an increase in jet pressure above 40 MPa. The most effective jet configuration for the reduction of cuter forces was found to be four coherent water jets, two lateraly disposed on each side of the cuter and directed at the arc of contact between the cutting edge and the rock.

Jan 1, 1987

An International Ferro-alloys Congress, arranged by the Ferro Alloy Producers' Association of South Africa, the South African Institute of Mining and Metallurgy, and the National Institute for Metallurgy, will be held in Johannesburg, South Africa, in April 1974. The technical programme, occupying five days, will cover the following topics in relation to all ferro-alloys: 1. Burden preparation, blending, pelletization, handling, reducing agents. 2. Electric smelting furnaces-design, operation, management,- smelting optimization, shop practice, refractories. 3. Mineralogy, reduction behaviour, smelting reactions, slags. 4. Automation, Pollution control. 5. Applications, trends in comsumption, trends in composition specifications. There will be no parallel sessions. Papers in the above topics are invited; review papers will also be welcome. Proposed titles and abstracts in not more than 200 words should be submitted before the 30th of November, 1972, to The Chairman, Programme Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa. The abstracts will be considered during January 1973, and papers accepted for the Congress must be submitted in final form before the 31st of July, 1973. The proceedings of the Congress will be published as a special volume. There will be a series of post-Congress tours to ferroalloy plants and other places of both technical and scenic interest. A full ladies' programme will be arranged. The First Circular, giving further details, can be obtained from: The Secretary of the Organizing Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa.

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007

By C. S. Northcote, I. F. Buchan, L. F. Baars

In 1969 the Coal Division of the Anglo American Corporation was awarded the tender to supply coal to the new 3000 MW power station to be erected at Kriel, which is situated midway between the towns of Ogies and Bethal in the eastern Transvaal. The coal was to be supplied from the No. 4 Seam in the Kriel Area of the Witbank Coalfield. The No. 4 Seam in this area varies in depth of overburden from 75 m to 6 m, with an average of 55 m. Initially, the mine was planned as an underground mine incorporating a three-shaft system for transporting some 8 million tons of coal per annum to the power station. As the result of negotiations between Anglo and Escom to improve the volumetric extraction of coal from the new mine, the Kriel Division of Anglo Power Collieries was finally planned to produce 4,1 million tons of coal from an underground mine and 4,5 million tons from an opencast mine, with a resultant increase in volumetric extraction. This paper describes the opencast operation at Kriel, with particular reference to the water problems encountered and to the operation of the draglines on sloping ground to a depth of 40 m to the top of the coal seam.

Jan 1, 1980

By P. J. van Staden, T. W. Walker

The Minfurn is a novel carbon-regeneration furnace developed at Mintek. It combines the advantages of direct resistive heating in a vertical-tube furnace with those of continuous operation, in a furnace whose capital, operating, and maintenance costs compare favourably with those of conventional rotary kilns. After successful tests under experimental conditions on carbons containing different contaminants, a 3 kg/h unit was installed on the carbon-in-pulp (CIP) plant at the Klipwal Gold Mine near Piet Retief, where it has been operating at, on average, 123 per cent of its design capacity. Since the installation of the Minfurn, monthly average losses of dissolved gold of less than 0,02 p.p.m. have been maintained for several successive months for the first time since January 1989. It is also possible that the monthly average residue values have been reduced. Further improvements to the carbon circuit are possible, and the possibility of making further savings by a reduction in the carbon-throughput rate still needs to be investigated. The mathematical modeling of the furnace has progressed to the stage where the future scale-up and design of the Minfurn can be carried out by simulation of the performance of different designs, and choosing the design that yields the desired performance.

Jan 1, 1993

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

By G. H. Morton

The tenth international symposium on the application of computer methods in the mineral industry (APCOM) was held in Johannesburg in April; the first time it had taken place outside North America. In the technical sessions fifty-seven papers were presented, providing a review of current work and including some important original contributions. These papers and a full account of the discussion at the symposium will soon be published in a single volume. The Technical Programme The first session of the symposium included an opening address given by Mr J. W. Shilling, President of the Chamber of Mines of South Africa, and a keynote address by Mr K. F. Lane of the Rio Tinto Corporation Limited. Mr Shilling spoke about the history of the South African mining industry and about some of the work of the Chamber of Mines. He stressed the importance of the symposium in familiarising those in mining with computer applications, and expressed his hope that it would stimulate and inspire scientists and engineers in the effort to develop safer and more economic methods of mining. Mr Lane, talking about economic and financial modelling, gave a fascinating account of the experience of RTZ over the last twelve years. In a very honest appraisal of the substantial progress that had been made, he confessed some disappointment not only in the cost and

By B. B. Mamba, J Ndalamo

The existence of an impressive reserve of oxidized cobalt-copper bearing ores in the African copper belt area lead the GECAMINES (DRC) to develop specific and adapted mineral processing routes (Mulaba-Bafubiandi, 2001). During the conventional diluted sulphuric acid leaching of oxidized cobalt-copper bearing ores commonly referred to as ?heterogenite?, more than 10% cobalt dissolution yield increase was observed in a plant situation (Mwema et al., 2002) when SO2(g) was flushed into the acidified cobalt leaching solution. The present paper attempts to elucidate mechanisms involved which lead to the increase of total cobalt as SO2 is flushed during the leaching of oxidized cobalt bearing minerals. The kinetics of cobalt dissolution as SO2 is flushed into the acidic solution as well as a full characterization, using UV-Visible spectroscopy, of Co2+ and Co3+ species present in the collected leachate are presented while possible effects of the presence of Cu and Fe on the leachability of cobalt bearing minerals present in the oxidised ore will be discussed. In the view of speeding up the leaching process, the mixed cobalt-copper oxidised ores were microwaves pre-processed. Preliminary results were also discussed.

Jan 1, 2007

The auriferous Carbon Leader reef which is the subject of this study can be subdivided into two types of sedimentological units, each with its characteristic spatial variability. For the longwall mining method applied at Western Deep Levels gold mine, subdivision of the orebody improves the estimation of the actual error variance, but not the grade estimates themselves. This can only be achieved by choosing oreblocks of a size and shape that are maximal parallel to the longwall and minimal at right angles to it, within the limits of mining restrictions. While simple kriging is the only method that gives unbiased results, the difference between untransformed and logtransformed kriging is negligible.

Jan 1, 1987

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

DECEMBER, 1971 The Wanders Club, Johannesburg Sunday, 9th April, to Friday, 14th April, 1972 The Tenth Symposium which is the first ever held outside the North American continent is being organised by the South African Institute of Mining and Metallurgy (with the South African Council for Scientific and Industrial Research and the South African Council for Automation and Computation), in collaboration with the previous co-sponsors. '" The programme includes over 60 papers from thirteen different countries. Attendance promises to be good and interested parties who have not yet registered are earnestly requested to do so without delay. The closure date for registration application is 31st January, 1972. The objective of this symposium is to pool experience and knowledge and to discuss new and potential developments for the planning and control of mineral projects. The papers which are to be presented will indicate the progress which has been made in this direction through the successful application of operations research, mathematical, statistical and computer methods. The intention is to bring together those persons responsible for managing various operations in the mineral industry with those engaged in the development of such mathematical and computer techniques as could assist this management. All interested parties are welcome. PRE-REGISTRATION (please return enclosed form as soon as possible). Applications for registration close on January 31, 1972. The fee payable on application will be R70. Late applications may, subject to vacancies being available,

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

By S. Budavari

The effects of shaft pillars left in deep-level hard-rock mines during the extraction of tabular deposits were studied some time ago, resulting in the formulation of design principles and procedures, which have been used with success in the design of shaft pillars in the deep-level gold mines of South Africa. The method has not yet been utilized in the design of shaft pillars in shallow and moderately deep hard-rock mines. The purpose of the present study was to remedy the situation since a great number of deposits are worked at those depths. The object of this paper is to present governing equations for the components of stress and differential movement as derived by use of an elastic model. The pillar is taken to be circular in the plane of a horizontal deposit. On the basis of the numerical results obtained, a study was made of the distribution of the vertical strain and tilt along the axis of the shaft, and of the vertical stress along the shaft and across the pillar. In every case investigated, the most adverse geometry was taken into consideration. By use of an empirical criterion and the results of some in situ observations, the determination of pillar dimensions and differential displacement components for South African gold-mining conditions is demonstrated. Pillar dimensions for shallow and moderate depths are compared with those accepted for deep-level conditions.

Jan 1, 1986

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007