Search Documents

By D. D. Marsden, L. E. Kun

Although a regulation is in force that all water used underground shall be free of bacterial contamination, in practice it is often very difficult to accomplish this. The standard method of disinfection m South African mines IS treatment with calcium hypochlorite, although liquid sodium hypochlorite is used at a few sites. Primarily because the process depends on human control for the addition of the hypochlorite and the regulation of its now, it is frequently found difficult to disinfect mine water adequately and continuously. In many marine environments, chlorine generated by the electrolysis of seawater in its passage through an electric cell is used for disinfection. The generation procedure is continuous and needs no human control except for occasional checking of the equipment. This paper describes the successful implementation of the process, suitably .modified, .at four underground sites. After severe scaling problems had been overcome, a procedure resulted that chlorinates considerably more effectively than the previous system (dosing with calcium hypochlorite), and that has a lower amortized operating cost.

Jan 1, 1981

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By D. J. Bosman

The impoved densification of sludge from neutralized acid mine drainage. by D. J. BOSMAN, B.Sc., (Member) The paper describes an investigation aimed at finding a solution to the accumulation of acid mine drainage in the old workings at Coronation Collieries, Kromdraai. The problem involved the neutralization of the acid in the water, without the large volumes of sludge and the large amounts of dissolved solids that usually result from neutralization. Pilot-plant work on the site using a limeneutralization process developed at Bethlehem Steel Corporation (U.S.A.) showed this to be a feasible method. A sludge of 22 per cent density was obtained under optimum operating parameters. The amount of suspended solids in the overflow water was very high, but this does not give rise to concern because the full-scale plant at Kromdraai will practise secondary sedimentation by running the thickener overflow through large dams with a theoretical retention time of 25 days. An analysis of the theory underlying the process is also made.

Jan 4, 1974

By A. C. Legg

BCL Limited operates a nickel-copper flash smelting operation at Selebi-Phikwe, situated in north-eastern Botswana. The original furnace was commissioned in 1973 and produces a high grade sulphide matte, from its own concentrates plus additional custom feeds, which is shipped to refineries in Zimbabwe and Norway for further processing. In 2004 the company embarked on a study to modernize the flash smelting complex, with an emphasis on extending campaign life, improving the furnace integrity and enhancing throughput and process efficiency. First phase initiatives from this exercise, including the fundamental switch to a single concentrate burner operation of the flash smelting furnace, were implemented in July 2007. This paper summarizes experiences prior to implementation, details the specific improvements made to the flash smelting furnace and associated operations, highlights the improved plant performance after modernization, and outlines second phase expansion plans that are currently under consideration.

Jan 1, 2009

By W. T. Ruhmer

Slimes-dam construction in the gold mines of the Anglo American Group by w. T. RUHMER. Pr.Eng.. B.Sc. Eng. (Met.) (Fellow) Current practices generally in accordance with the principles of design and operation of slimes dams within the Gold Mining Division of the Anglo American Corporation are described. Although many of the details given are either obvious or have been amply dealt with elsewhere, these have been included for the sake of completeness. The selection of suitable ground for the deposition of slimes, the initial design and construction of a slimes dam, and its consequent operation are presented in logical sequence. Emphasis is placed on the code of practice for the construction of slimes dams issued by the Chamber of Mines of South Africa, and draft regulations (Water Act of 1956) dealing with pollution. Operating costs are included, and possible future trends are discussed.

Jan 2, 1974

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By R. D. Beck

The minerals industry needs the support of al sections of the population if it is going to be able to supply the new materials required for future development. It will achieve this support only if its image is good. Perceived images of the minerals industry are examined in respect of history, technology, environment, safety, education, and economics. Concern is expressed about the low technological image of the industry and the declining number of students enrolling in minerals-related disciplines. It is concluded that it is the professionals, through institutes like The South African Institute of Mining and Metallurgy, who must take the lead in improving the image of the minerals industry. The Presidential Address gives data to support this thesis; data that, is hoped, can be used in efforts to educate people about the minerals industry.

Jan 1, 1991

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The performance of the improved microclimate suit by N. B. STRYDOM M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, B.Sc. (Potch.) (Visitor), and W. H. VAN DERWALT, M.Sc. (Potch.) (Visitor) An assessment has been made of a new improved microclimate jacket when worn by men working for four hours in a hot environment (wet-bulb temperature of 33,9°C and an air speed of 0,4 m/s) and at work rates of 35 Wand 70W. At the lower rate of work in heat, the use of microclimate suits maintained the rectal temperatures of the men at almost the same level as when they worked without that protection at normal room temperature (20°C). At the greater rate of work without protection, the men's rectal temperatures rose to 40°C within two to three hours, so that they could not complete four hours of work. When they wore microclimate suits, they easily completed four hours of work, and their rectal temperatures were lower than when they worked at the lower rate without protection.

Jan 8, 1975

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

By J. H. Viljoen, N. B. Strydom, J. S. Greyson, C. H. Van Graan

SYNOPSIS Bad eyesight and poor illumination can contribute to the occurrence of accidents in mines. As one part of a study of this problem, surveys of light intensities have been conducted in 19 gold mines. On 17 of the mines the surveys were on one underground level only, whilst in two of the mines more intensive surveys were conducted by measuring light intensities in all areas to determine any inter-mine variations between the levels of illumination. Readings of light intensity were taken underground at stations, tips, winches, stopes, conveyor belts, waiting places, pump stations, fitters' and boilermakers' workshops, ambulance rooms and in haulages. It is concluded that the average levels of illumination in South African gold mines are comparable with those reported in the literature for mines elsewhere. Standardisation of lighting conditions underground could eliminate inter- and intra-mine variation in illumination levels where they occur. A guide to mine illumination practice would assist such standardisation, and help increase the levels and effectiveness of illumination in mines. Some suggestions are made in this latter connection.

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

By H. A. D. Kirsten

The professions are subject to a wide range of changing conditions, and are as a result forced to become more competitive. Although there is a need for specialization under these circumstances, no formal recognition, definition, or control of specialists exists. Some of the professions have attempted, over extensive periods of time, to resolve the issues involved, and have met with varying degrees of success. It appeared from the replies to a questionnaire sent to over one-hundred-and- .fifty professionals, that both advanced education and experiential training, are considered to be necessary qualifications for specialization. The opinion as to whether it should be lift to the individual to cal himself a specialist, or whether recognition should be based on peer review, was divided The majority did not want the number of specialists to be controlled The response to the reservation of work for specialists was ambivalent.

Jan 1, 1995

By L. A. Vermeulen

Electronic circuits were developed and successfully utilized to record, store, and continuously transmit to a remote station physical information relating to the impacts of pebbles on the shell liners of an industrial pebble mill, and of electrical conduction in the mineral pulp. The information was obtained by the instrumentation of some of the bolts that are used to clamp the liner blocks and litter bars to the mill shell. The features associated with the impact and conduction signals have been interpreted, and it is shown that such signals can lead to continuous measurements of the volume of the load in an industrial mill. Information is given regarding the angular distribution of direct impacts of the pebbles onto the shell liners, the power required to promote impacts, the amount of material in flight, the impact velocity, and the average number of direct impacts with the shell liner that any given pebble undergoes in unit time in the given mill.

Jan 1, 1984

By J. M. Barnard, M. P. Brandt, L. E. Korwin-Kossakowski, W. H. Smith

Petrographic analyses of coal rank and maceral-group composition are widely used in the characterization of coal. This paper describes the use of an image analyser (IBAS Kontron) for fuly automated measurements of the rank and maceral groups of seam coals. The rank is then derived from reflectance histograms, or 'fingerprints', of coal reflectance distributions (being expressed as the mean random reflectance of vitrinite). The volume proportions of the maceral groups are calculated from the histograms. The results obtained with the IBAS were generally in agreement with those obtained by conventional methods of reflectance measurement and point-count analysis. However, the results were inconsistent for coals with a bimodal character or a wide V-class distribution. The rank of the analysed coals ranged from 0,50 to 1,10 per cent mean random reflectance. The lowest reflectance that can be analysed with the IBAS is 0,4 per cent. The speed, objectiveness, and repeatability of this technique make it exceptionally suitable for use in the quality control of large numbers of samples.

Jan 1, 1990

By J. A. L. Napier

By use of a functional model of capital expenditure developed earlier, a prototype cash-flow model is formulated as a basis for the investigation of the economic consequences when the production rate of a mine is manipulated as fundamental design variable. The optimum production capacities that maximize the common economic criteria of net present value, present-value ratio, and wealth growth rate are determined. It is shown that these choices depend certain key groupings of the economic parameters, and that they have a fixed interrelationship. The basic cash-flow model is extended further to include the effects of a constrained rate of production buildup and the imposition of State taxation on generated income. An approximation to the initial tax-free period of a new mining venture is developed, and, by use of these results, the optimum choice of production level is analysed when both the buildup rate is constrained and tax is imposed. This extended model permits a comparison between the performance of existing mines and the predicted theoretical production levels for these mines.

Jan 1, 1981

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

The comments by Mr Chaston were constructive and much appreciated. Considering firstly the recovery of cassiterite from fine deslimed material. A size distribution analysis shows that 58 per cent of cassiterite in Union Tin flotation concentrate reports in the minus 15 micron (quartz) size range. This is achieved at a recovery of 67 per cent and concentrate grade of 42,6 per cent. It is of interest to note that at Altenberg in East Germany 85 per cent of the tin in deslimed minus 43 micron material is recovered into a 14 to 16 per cent Sn concentrate using para-tolyl arsonic acid as collector. Reconcentration of this material is then carried out using two shaking table stages which recover 53 per cent of the tin in a 50 per cent Sn concentrate. Flotation was resorted to after recovery rates of 35 per cent and concentrate grade of 30 per cent had been achieved in a 275 ton per day plant comprising 130 tables. Tests on tabling of deslimed minus 43 micron material have not been carried out at Union Tin. The cost of equipment actually associated with cassiterite flotation amounts to about R60 000. The

By Nareetsile S., J. Kabwe

In the past few years Orapa and Letlhakane Mines have investigated various new technologies to enhance and improve production. The goal has been to improve productivity, reduce operating costs and make the mines more profitable The advent of Global Positioning Systems (GPS) in the early ’80s brought about the realization of this concept. Orapa and Letlhakane Mines started using GPS in 1999 and it is now used atLetlhakane mine for surveying, vehicle tracking and dispatching and for floor control system. Orapa Mine uses GPS in surveying, floor control and drill navigation. It will also be used for vehicle tracking and dispatching in mid-2001 following the installation of a fleet management and control system. The introduction of GPS at both Orapa and Letlhakane mines have improved productivity and reduced operating costs in the areas of drilling, topographic survey and floor control. In vehicle tracking and dispatching GPS has allowed for real-time information management for timeous decision-making which optimized fleet run time hours.

Sep 1, 2001