Search Documents

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By M. R. Anderton

"A hierarchical four-character code designed for geological and allied data may be used to log exploration drill-holes and store the information on magnetic media. The code is intended for use in semi-free format and permits the collection of as much, or as little, data as the geologist may require for the purpose in hand. A method of data storage by variable length records is discussed.Information may be retrieved by means of a simple enquiry language. Optional output facilities could allow the retrieval of data in a form suitable for direct input to a contouring package. The enquiry parameters and interrogation program can thus provide the interface between the data bank and associated application systems."

Jan 1, 2014

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By M. M. Oosterveld

"In South West Africa diamonds are mined from ancient beach deposits by the Consolidated Diamond Mines of South West Africa, Limited.To improve the control of mining production, a computer is used for the calculation of statistically more accurate and homogeneous ore blocks. Geological and sampling information has been digitized and stored on magnetic files.The figures derived for each block entail the calculation of the diamond size frequency distribution, the diamond density distribution and the ore reserve by using the density distribution.The diamond size frequency distribution is used for estimating the revenue in an ore block.A description is given of how a linear programming system can be used for production planning."

Jan 1, 2014

By A. C. Coetzee

Blinkpan Koolmyne is as ten voile gemeganiseerde steenkoolvoorsiener aan die 1 000 MW Evkom-kragsentrale in die Oos-Transvaal, onderhewig aan groat seisoenale produksieskommelinge. Die aanwending van 'n groat bogrondse oap opgaarhoop vir die uitstryking van hierdie wisselende aanvraag word beskryf. Twee produksierasionaliseringsfases wat hierop volg het besondere bemoedigende resultate gel ewer, beide in toerusting- en mannekrag-produktiwiteit. Die aanwending van 'n rekenaarprogram vir die simulering van ondergrondse afbouaktiwiteite met die oog op toerustingkeuse, word aangegee. Voorlopige resultate wat in die praktyk behaal is dui op 'n hoë mate van betroubaarheid vir die program, terwyl die gebruik van die nuutste tipe hoë -kapasiteit laaimasjiene, koolsnyers en wisselkarre, groat potensiaal inhou.

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025

By M. de Beer

The conversion of carbon-containing feedstock into liquid fuels can proceed via the Fischer-Tropsch synthesis, which is catalysed using supported cobalt catalysts. These catalysts contain noble metals to facilitate the reduction of oxidic cobalt species in the catalyst precursor to metallic cobalt, which is the catalytically active species for the Fischer-Tropsch synthesis. This is thought to occur via hydrogen spillover, i.e. the diffusion of atomic hydrogen over the support from the noble metal to the oxidic cobalt moieties. Noble metals may also affectthe dispersion of cobalt in the active Fischer-Tropsch catalyst. The economic aspect of the addition of noble metals to the Fischer-Tropsch catalyst is discussed.

Jan 1, 2014

By F. P. Janse van Rensburg, P. J. Le Roux

"There are numerous factors that affect open stope stability and often result in falls of ground. These falls of ground can be attributed to factors such as beam failure due to a larger than normal roof area (hydraulic radius too large), adverse ground conditions, seismicity, the stress-strain environment, absence of support, and poor drill-and-blast practices. The effect of time on the stability of open stopes is sometimes underestimated and is relatively unknown, especially on Target Mine. Actual data was collected from open stopes at Target and analysed to show the effect of time on open stope stability. The benefits of this analysis will include improved understanding of time-dependent failure, which can assist in reducing dilution and the risk of sterilization of future mining blocks. IntroductionTarget Mine is situated adjacent to the town of Allanridge, some 20 km from Welkom in South Africa’s Free State Province, and is the most northerly mine in the Welkom Goldfields area (Figure 1). The mine consists of a single surface shaft system with a sub-shaft (Target 1C shaft) and a decline. Ownership was attained by Harmony Gold Mining Company Limited in May 2004 (Harmony Gold Mining Company Limited, 2010). Before discussing the selection of open stopes for the back-analyses, a brief explanation of open stoping as practiced at Target Mine will be given. The orebody is some 180 m in thickness and 270 m wide and comprises multiple reefs overlying one another. The 180 m thick reef package is termed the Eldorado Reefs, as shown in Figure 2. The Eldorado Reefs suboutcrop against the Dreyerskuil Reefs, as shown in Figure 3. The dip of the reef varies from as low as 10° in the west to 75° in the east.Compared with most Australian and Canadian open stoping mining operations, Target Mine is unique. In most Australian and Canadian mining operations the hangingwall and footwall of the open stopes comprise waste rock, and the orebody dips relatively steeply. Due to the depth of Target Mine, some 2300 m to 2500 m below surface, a destress slot (Figure 4) is mined to create an artificial, shallow mining environment whereby the field stress is managed and kept at values of around 60 MPa. The destress slot comprises a narrow tabular stope with an average width of 1.5 m, and is mined on the Dreyerskuil Reefs.At Target Mine the hangingwall, sidewalls, and footwall of the open stopes all comprise reef of different grades, except for the EA1, where the EB footwall is waste rock. If a stope, for example, is mined alongside an existing old stope, the western sidewall of this stope will consist of backfill. The general mining direction of open stopes is from the lowest position of the reef on the west, progressing up towards the east as shown in Figure 5."

Apr 1, 2019

By G. Bueno, L. M. Tavares, T. M. Campos

Iron ore pellet feed pressing has been one of the first and most successful applications of High- Pressure Grinding Rolls (HPGR) in the minerals industry. Vale S.A. has been one of the pioneers in this application, currently with six HPGRs in operation in the pelletising plants of the Complexo de Tubarão (Brazil). In spite of the important advances in the technology, risks still exist when scaling-up the process from small-scale information. The present work takes advantage of the recent advances in the mathematical modelling of the HPGR performance, using the population balance model to evaluate the modified Torres and Casali model prediction in iron ore pellet feed pressing for different scales of operation. Results are presented that compare the HPGR performance in different operational scales for iron ore pellet feed pressing, demonstrating the confidence of this model-based approach for scale-up to full-scale HPGRs used in pressing iron ore concentrates. Keywords: Scale-up, HPGR, pellet feed, modelling, simulation

Jan 1, 2020

By F. Dutoy, M. B. Stella, C. F. Carrozza

Rare earth elements (REEs) are indispensable components in the manufacturing of high-tech devices, renewable energy technologies, and defence applications. As global demand for these elements continues to rise, there is a pressing need to optimize extraction processes for both efficiency and environmental sustainability. This study explores approaches to rare earth extraction using Ionquest® 801 and integrates a predictive modelling to enhance process understanding and optimization. We conducted a screening test varying pH process to evaluate the best extraction efficiency. Starting pregnant leach solution (PLS), solution was prepared in the lab with the following rare earth elements: La, Ce, Gd, Dy, and Υ, at 0.02 M for each element. The data obtained were used to develop empirical and mechanistic models to predict rare earth extraction yields and flowsheet. Further tests were performed by mixing specific concentrations of different extractant and/or phase modifier. Our experimental results demonstrated the effectiveness of the proposedextraction methods, highlighting improvements in both yield and selectivity. The developedmodels successfully captured the complex relationships between process parameters and extraction efficiency, providing valuable insights for process optimization.

Nov 6, 2024

Slope stability is a fundamental part of a successful mining operation. It impacts directly on the safety of personnel and the economics of the mine. The Jwaneng Mine in Botswana is planning a push back of 644m depth in the south east wall. Mining will commence in 2010 and be completed in 2024. This will put the mine in the deep pit category. The mine has invested in extensive geotechnical data gathering and design programs that started as far back as 2003 for the south east wall. The south east wail of Jwaneng Mine is characterized by foliation that dips adversely into the mining faces. The orienta1ion of the foliation is variable due to intense tectonic movements that have also caused the occurrence of faults that are sub-vertical. A considerable amount of information on the characteristics of structural patterns and the rock mass has been collected. This paper presents an overview of the feasibility level geotechnical design that is about to be concluded.

Jan 1, 2010

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By B. Genc

Safety in South African mines is a subject of significant interest, since many mining companies are experiencing production deficits due to safety-related stoppages. In this paper, safety data from the South African platinum mining sector is analysed for the period 2006 to 2010. The data was obtained from company annual reports as well as the Department of Mineral Resources, and analysis in the study is limited to injury and fatality data only. The overall safety performances of companies in the sector are compared, and opportunities for benchmarking and recognising potential sources of best practice amongst platinum miners are identified. Improving safety usually incurs a cost, and mining companies are particularly conscious of the importance of controlling costs. However, cost considerations often deal only with direct costs, and it has been shown that indirect costs are usually far more significant. Therefore, a greater safety spend will usually result in the creation of value for the mine since it will reduce the indirect costs associated with accidents. The results of some recent research in this area are presented. In this light, where available, the financial performances of mining companies in the sector, obtained from published annual results, are included in the benchmarking exercise to determine whether there is any correlation with safety performance.

Jan 1, 2012

By N. Baloyi, P. Popoola, M. Tlotleng, S. L. Pityana

"The advantages of using Nb and Ti-Nb coatings for improving the hardness and corrosion resistance of Ti6Al4V were investigated. It has been reported that Ti6Al4V used in orthopaedic implants tends to release toxic Al and V ions into the surrounding tissue. Thin layers of Nb and Ti-Nb were deposited on Ti6Al4V substrates using a laser metal deposition technique. The deposited material was analysed using optical microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffraction. The corrosion behaviour of the deposited layers was investigated using a Metrohm Autolab PG Stat101 compact potentiostat at 25°C in simulated body fluid. A Vickers hardness system was used to study the mechanical properties. Both Nb and Ti-Nb coatings exhibited good metallurgical bonding with the substrate. The microstructure and the XRD analyses for the Nb system showed that the ??-Nb phase was most dominant, while the Ti-Nb system comprised a mixture of the ?? and ?? phases. The average hardness of the Ti6Al4V substrate was 350 HV0.3, with a slight increase for the Nb coating (363 HV0.3) and a much higher hardness from the Ti-Nb coating at 423 HV0.3. The corrosion results show that the deposited Nb was more corrosion-resistant in the solution than either the Ti6Al4V substrate or the Ti-Nb coating. IntroductionMetals such as CoCrMo, 316L stainless steel, and NiTi alloy are used for manufacturing biomedical implants because of their distinct properties, including low Young’s modulus and resistance to corrosion (Ryan, Pandit, and Apatsidis, 2006). These implants are required to remain in the body of the patient for many years. Due to a favourable combination of mechanical and corrosion properties, titanium (Ti) and its alloys have emerged as the material of choice for biomedical implants. Nevertheless, their use is not entirely without challenges. For example, in total hip replacement, surface degradation and release of metal debris from metal erosion caused by friction limit the service life of the implant (Oldani and Dominguez, 2012; Manivasagam, Dhinasekaran, and Rajamanickam, 2010). Ti6Al4V is generally regarded as the material of choice, but it has been found that over extended periods of time, the combination of surface corrosion and erosion releases toxic aluminium (Al) and vanadium (V) ions into the body (Khan, Williams, and Williams, 1996). This has led to the investigation of titanium alloys containing niobium (Nb), zirconium (Zr), tantalum (Ta), and molybdenum (Mo) as substitutes for the aluminium- and vanadium-containing Ti6Al4V (Okazaki et al., 1997)."

Apr 1, 2019

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023

By M. Rhodes

The Sukari project, which is owned by Centamin Egypt Ltd, is located in southern Egypt, 770 km south of Cairo but close to the Red Sea. The project is the first new gold development in Egypt and was commissioned in the middle of 2009. In 2007, Centamin purchased the CIL plant from the Kori Kollo mine in Bolivia. This plant was originally designed to treat 6.5 Mtpa of oxide ore. The Sukari deposit contains an oxide zone close to surface with a thick zone of mixed oxide and sulphides below this. The sulphides contain relatively coarse pyrite and arsenopyrite with fine <10 µm gold inclusions. Eventually, the sulphide ore will be mined from underground. Metplant Engineering Pty Ltd, a subsidiary of Bateman Engineering Pty Ltd was contracted to design modifications and additions to the Kori Kollo plant to enable it to treat the Sukari ores. The plant was designed to treat the three ore types in stages. Throughput was set to 4 Mtpa, dueto Sukari ore being harder, at a head grade of 1.7 g/t to produce 200 000 oz of gold. The oxide circuit was based on the use of the Kori Kollo plant and the difference with mixed ore was that the oxide circuit would treat flotation tailings rather than ore. This circuit has a leach capacity of 26 000 m3 and residence time of 24 hrs The main feature of the upgraded mixed ore plant was the addition of a flotation circuit to produce a concentrate which would be reground and treated in a separate leach and elution circuit. Ore is crushed in a gyratory crusher and the comminution circuit uses a conventional SABC producing a product with a P80 of 150 microns. The throughput of 580 tph of oxide ore and 500tph of mixed ore was set to match the mills from Kori Kollo, with the addition of the pebble crusher to accommodate the more competent Sukari ore. The flotation circuit comprises a single rougher circuit to maximize recovery. The concentrate is thickened prior to regrinding which is carried out in a tower mill and two SMD mills operating in series. The final product, with a P80 of 12 microns, from the regrind circuit is leached in a CIL circuit with a total capacity of 2 550 m3. Gold is recovered through a conventional pressure Zadra circuit. Tailings from both circuits report to separate tailings thickeners and are pumped to a tailings storage facility. The circuit is designed to maximize the recovery of water. The project lies in one of the driest deserts in the world and a feature of the operation is the use of sea water from the Red Sea. This water is pumped 25 km from the coast.

Jan 1, 2009