Search Documents

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By William P. Diamonds, David C. Oyler

Stimulated vertical boreholes are an effective means of removing gas from coalbeds in advance of mining. This Bureau of Mines report examines the coal mine roof damage potential of stimulation treatments. Twenty-two Government-sponsored stimulation treatments have been mined through to determine the effects on the coalbed and roof strata. Vertical fractures in the coalbed were discernible for most treatments and horizontal fractures were present for about half of the stimulations. Sand-propped vertical fractures were usually short in lateral extent. Evidence of stimulation fluid movement could generally be traced beyond the maximum extent of sand-filled fractures when fluorescent paint was added to the treatment fluids. The maximum lateral extent for a sand-filled vertical fracture was 416 ft and a paint-coated vertical fracture extended 630 ft. Horizontal fractures were generally found within bedding planes, most commonly on top of the coalbed. The maximum lateral extent for a horizontal fracture was 265 ft at a coalbed depth of 630 ft. Horizontal fractures have been found to occur as deep as 1,145 ft. Penetration of strata overlying coalbeds was observed in nearly half of the treatments intercepted. Most of these occurrences have been interpreted to be penetrations into preexisting joints. No roof falls or adverse mining conditions were encountered that could be attributed to the stimulations.

Jan 1, 1987

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By JOSEPH F. CULLEN, Dorsey A. Lyon

In connection with its investigation looking to the prevention of waste and the increase of safety and efficiency in the mineral indus- tries the Bureau of Mines has undertaken a study of the possible uses of the electric furnace in metallurgy. This bulletin presents a com- pilation of such data as seem to be useful for the information of persons who may be interested in the matter. In the application of electricity to metallurgy three kinds of processes are involved, namely, mechanical, thermal, and electrolytic. Under the mechanical application of electricity come those proc- esses of dressing and concentrating ores that are known as either electrostatic or electromagnetic processes. In electrothermic processes the current is used as a source of heat. The fundamental differences between the various types of electric furnace that are at present in commercial use relate to the manner in which the electric current is applied, as may be noted by reference to that part of this report in which the subject is discussed. In electrolytic processes the electric current is used for depositing metals from solutions. The process may be conducted in one of the following ways: (1) The material to be treated may be put into solu- tion and then electrolyzed, the material thus treated forming the electrolyte; (2) the material to be treated may form the anode or be placed in contact with the anode; or (3) the material to be treated may form the cathode or be placed in contact with the cathode. This report treats of electrothermic processes, with the possible exception of those for the reduction of aluminum from its ores. Moreover, of the processes used in the so-called electrochemical in- dustries only those for the reduction of an ore to metal, or to a com- pound of the metal that is of value in itself, or is an aid in metallurgical work, are here discussed.

Jan 1, 1914

By Ludwig Schmidt

The policy of buying crude oil on a gravity basis , recently instituted by the major crude oil purchasing agencies in the Mid- Continent field , has caused a new and vital interest to be taken in the work of the U. S. Bureau of Mines for preventing evaporation of crude . From the early years of the industry oil men have recognized that the gravity of crude oil is usually an index of the gasoline content , but it has not been so generally known that the gravity of the crude oil decreases if evaporation is permitted . In 1919 the Bureau of Mines began a survey to determine the evaporation losses of crude petroleum in its various stages of handling from the well to the refinery , The results of this study are presented in Bulletin 200 ( Wiggins , J.H. , Evaporation losses of petroleum in the Mid- Continent Field , Bulletin 200 , U. s . Bureau of Mines , 1922. ) and Bulletin 225 ( Wiggins , J.H. , Methods of decreasing evaporation losses of petroleum , Bulletin 225 , U. S. Bureau of Mines , ( In press ) The findings of this survey were so startling that soon after the preliminary report had been published , several tank companies began manufacturing vapor- tight tanks for the purpose of reducing these important losses . Since that time the development of this type of apparatus has been so rapid that today , every oil trade journal carries numerous advertisements of vapor- tight tanks and equipment as well as technical articles dealing with various problems in connection with the elimination of evaporation losses , whereas three or four years ago the subject was scarcely even thought of. The present report has been prepared in response to numerous requests for information on the apparatus actually being used to prevent evaporation losses . At this time oil operators are also extremely interested in holding the lighter fractions in the crude oil in order to prevent a lowering in gravity . The practice of removing the vapors from crude- oil tanks by means of a slight vacuum and extracting the gasoline from them is not discussed here .

Feb 1, 1923

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948

By G. S. Rice

To those concerned in attaining greater safety to life and incidentally to property in coal mining, the meeting of representatives of the national mine safety research organiza¬ tions of the principal coal-producing countries, which was called by the Safety in Mines Research Board of Great Britain at its experimental station near Buxton, should have deep significance. It is notable, first, because it meant the friendly cooperation of countries not many years ago engaged on either side in the great World War; and second, because of the remarkable degree of agreement in the essential fundamental factors and methods of attaining greater safety in coal mines when it is considered that the questions were approached by different paths and that the applications dealt with widely differing natural conditions and national points of view. Varying views, of course, were held as to the relative importance of certain factors, but the differences were of detail rather than of principle. When the meeting adjourned it was unanimously agreed that such meetings should be continued annually and that the greatest benefit was to be derived by close cooperation in the exchange of data. Belgium, France, Germany, Great Britain, and the United States were represented by one or several members of the respective national research organization. It is of interest to note that this research work in Belgium, France, and Germany is supported directly by na¬ tional organizations of mine operators or owners but placed under a scientist appointed by the respective Government, thus giving the work official standing. In Great Britain the work is carried on by a Government board, consisting of persons connected with the coal¬ mining industry or in mining research, appointed by the Secretary for Mines, to direct the work of research of the Mines Department. It does not, however, come under its inspection service. Its work is supported by a penny-a-ton tax on output of coal. In the United States the mine-safety research work is directly supported by the Federal Government.

Dec 1, 1932

By A. Gene Collins

Some of the geochemical relationships that exist between subsurface fluids and the associated geologic strata in petroleum producing areas of Louisiana have been determined. Samples of petroleum-associated water were obtained from 126 wells in Louisiana that produced from sediments of three geologic ages: Tertiary, Cretaceous, and Jurassic. The samples were trans-ported to a central laboratory for analysis of chemical composition, using standard methods, to determine if the compositions varied with the geologic strata of their source and, if so, why. The dissolved constituents were com-pared with those of a brine that was concentrated by evaporation. The concentrations of bromide, calcium, and strontium were useful in distinguishing the brines produced from sediments of a late age from those of an earlier age. The concentration ratios of Mg' (total equivalent magnesium) and bromide indicated that dolomitization probably had occurred and altered the composition of the brines. A principal-components analysis of the data indicated an inverse relationship between depth and concentrations of bromide, strontium, calcium, and lithium.

Jan 1, 1970

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube's deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support's resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if primary gas toxicities that evolve during the early (~300° C) and later (~.400° C) combustion stages of polyvinyl chloride and chlorinated brattices could be predicted by a smoke particle characteristic, which could be used as a simple and inexpensive test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 2500 and 1,0000 C, for 14 min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCl) and carbon monoxide (CO) concentrations, sample and furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and number concentration (no), and the product of the average smoke particle diameter and concentration (dgno)' Results show that the inverse of the smoke particle diameter-concentration (l/dgno) correlates directly with the primary gas toxicities evolved during both stages of combustion.

Jan 1, 1989

By Terry J. Close

The highly-mineralized 43,700-ha Rapid River study area, on the southeast side of Hells Canyon Wilderness and west of the village of Cuprum, in Adams County, western-Idaho, was investigated in 1992 by the USBM (U.S. Bureau of Mines) in conjunction with its Idaho Land Assessment Program. The 1992 study updated data gathered during the USBM's 1974-76 Wilderness investigation. The studies consisted of the evaluation of 61 mineralized sites and the estimations of tonnages, grades, and minability of these sites. Most of the sites studied are in two mineralized locales--Windy Ridge and Jackley Mountain. A few isolated sites, peripheral to the two locales, were also examined. The 61 sites contained more than 340 mine and prospect workings, including about 10,300 meters (34,000 feet) of underground workings, plus 134 drill holes.

Jan 1, 1993

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By John H. Soulé

"INTRODUCTION The property of the Silver Spot Mines Co. is in the Boston Hill area within and adjacent to the southwest corner of Silver City, N. Mex. The area was visited by Bureau of Mines engineers 3/ in 1941 and 1942 during the investigation of possible sources of manganese. The area was visited again in November 1944 4/ to study the possibilities of geophysical exploration of the manganiferous-iron deposits. This geophysical work was performed in 1945 5/, confirmed the existence of known deposits of manganiferous-iron ores, and indicated the probable extent and situation of others.The Silver Spot property was churn-drilled from 1926 to 1929 during exploration for manganiferous-iron ores. The sludges from a number of the holes indicated low-grade lead-zinc mineralization. Lead and zinc minerals also were found on the dumps of some of the old shafts when the property was visited by D. H. Mullen, an engineer of the Bureau of Mines late in 1946. A diamond-drilling project was proposed. It was started in April 1947 with the intention of investigating the best of the known ore indications as shown by the old churn-drill holes and thus gathering new data upon which to base future work. Only one hole was drilled before the project was terminated because of lack of funds and time."

Mar 1, 1948

By L. C. George

The Bureau of Mines measured the vapor pressures of selected mixtures in the binary systems CdCl2 ?SnCl2, CdCl2 -ZnC12, PbCl2 ?SnCl2, and PbCl2 -ZnCl2 by the static pressure method. These data were evaluated by the second-law (sigma-plot) method. Equations expressing the vapor pressures and the heats and free energies of vaporization as functions of temperature are given.

Jan 1, 1969

By Jerome J. Hoeppner, Walter W. Fowkes

The Federal Bureau of Mines has determined the distribution of forms of sulfur for several lignites and gasification chars and noted the changes induced by the gasification process . A method was adopted for quantitatively determining sulfide sulfur that was found to be present in the chars , although absent in the lignites . Changes in the behavior and distribution of sulfur forms were further investigated concerning the ashing of lignites and chars under standard conditions , as well as at various temperatures , and the determination of volatile matter applied to both chars and lignites . The authors concluded that the first and greatest change in the form of sulfur present in natural lignite , upon heat treatment , resulted from the reduction of pyritic and sulfate sulfur to sulfide . Organically - bound sulfur originally present is less reactive , but largely disappears on strong ignition . An appreciable part of the sulfur content of natural lignite is fixed in the char as sulfide and in the ash as water - soluble sulfate and will affect the summation of constituents , to a greater or lesser degree , in reporting the ultimate analysis of a lignite or char .

Jul 1, 1960

By C. Lorimar Colburn

"The use of helmets during the war has accentuated interest in the advisability of using stiff hats in mines to protect the miners against falling rocks. About forty per cent of the accidents in mines are due to falling rocks or roof. A large number of these accidents could be prevented if the miners wore stiff hats or helmets.The use of head protective devices in minas is not new, for they have been in use for many years in Europe and in the Lake Superior District in the United States. In practically all of the mining districts in Europe stiff hats of some kind are required by the mine management. George S. Rice, chief mining engineer of the Bureau of Mines, reported that in Germany, Belgium, and France stiff hats made of papier mache or felt rosin are in use. Similar hats are generally employed in the Lake Superior District. In building the subways of New York and Philadelphia it was the practice of engineers and workers to let the hair grow very long and to wear a close fitting cap or felt hat. In Germany the hats are high like the military helmets, whereas in France and Belgium they fit more closely to the crown. In England the practice is mixed. As a rule the miners use soft padded caps, but in Yorkshire many of the miners use sole leather, tight-fitting caps of jockey pattern with the seam forting a little ridge down the middle of the cap. These hats are very useful allow thin beds of coal, as in crawling one is very likely to strike his head a sharp piece of rock or on a timber. Of course, such mishaps are more likely to occur to a man not familiar with the mine. It must be admitted such hats do not stick on well, though this is usually due to their not being especially fitted. The German hat is particularly unsuited to an American-shaped head.It is interesting to note that on the continent tight cotton caps are generally worn over the hair and under the hard hat. This is a measure for cleanliness which is excellent. In low beds of coal share much crawling on hands and knees is necessary the dirt and coal dust sift down, making the miner black and dirty. In metal mines stiff hats are of especial use in shaft work; also in raises or high stapes. A small fragment of rock falling some distance either down a shaft or raise would kill a man if it struck him squarely on the head. A stiff hat or helmet may protect him and save his life. At a station in a shaft where men are loading the cage or skip, some kind of adequate head protector should be compulsory. A head-protecting hat or cup which is also a good insulator should be worn where there is danger of striking one's head against a wire carving an electric current."

Jun 1, 1920

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By David Garry, Michael J. Brnich, Lynn L. Rethi, Henry P. Cole, William J. Wiehagen, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet and the trainee's questionnaire. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.1 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Supervisors, Safety Personnel and Accident Investigators Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Developing a strategy or plan to prevent slips and falls Following correct procedures in conducting an accident investigation Preventing unsafe work practices Recognizing and instituting hazard controls in the section Identifying and implementing safe work procedures Location: Underground coal mine section Problem: You have been the general mine foreman at White Rock Mine for 4 years and have worked at this mine for 12 years. The mine superintendent calls you into his office. He gives you an accident report of an employee in 4-G section who was injured while carrying rock dust bags from the rock dust car to a battery powered scoop. It is several days after the accident and the mine superintendent assigns you and the safety supervisor to thoroughly investigate the accident to determine all the contributing factors. Your job is to make specific recommendations to prevent future slipping/tripping accidents.

Jan 10, 1999