Search Documents

By John F. Wiggert

The first signal system used in the Homestake mine between the cagemen and hoisting engineers was a mechanical one. It consisted of small cables or jointed steel rods hung in the cage compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' positions by means of bell cranks and steel wires. At the various stations the bell lines were also fitted with bell cranks and connected levers, so that the cagemen could operate the bells from the stations when they were handling rock or other material and not riding on the cages. Such a system was inherited from the days before extensive electrical development. It served quite well for shallow shafts, but for depths of a thousand feet or more it was very slow and cumbersome. It required consider-able muscular effort to operate it quickly, because of the inertis of its great weight and also because of frictional resistance. The maintenance cost was quite high because of the many wearing parts.

Jan 1, 1937

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By T. H. Jeffers

To help maintain an adequate supply of minerals to meet national, economic, and strategic needs, the Bureau of Mines investigated the feasibility of extracting copper from coarse native copper ore with ammoniacal ammonium carbonate solution by a simulated in situ leaching procedure. A 5.9-metric-ton (6.5-ton) sample of minus 30.5-centimeter (12-inch) conglomerate-type ore analyzing 1.96 percent copper was leached in a column for 556 days with a solu-tion that contained, in grams per liter, 2.2 NBs and 1.9 CO[3=]. The copper extraction was 71.4 percent, and reagent consumptions were, in kilograms per metric ton of ore, 1.1 NBs and 0.85 CO[3=] (in pounds per ton of ore, 2.2 NH3 and 1.7 CO[3=]). The pregnant leach solutions contained about 1.4 grams per liter copper, which was readily extracted from these low-tenor liquors with a 1:19 mixture of an organic extractant and kerosine. Copper was stripped from the loaded organic with depleted electrolyte containing 150 grams per liter H2S04, and the copper was recovered by electrowinning with antimonial lead anodes. Conditions also were established for minimal lead transfer to the cathode copper.

Jan 1, 1979

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By R. V. Ramani

This volume is the third of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume IV: User's Manual for OPMHS/2. The Mine Coordinate Generator System serves as an interface between the Geology and Reserves System (Volume I, final report) and OPMHS/2 (Volume IV, final report) to provide local mine grid information which is used as input to the decision making process and dynamic simulation routines of OPMHS/2. After the Geology and Reserves System has been successfully run for a property, a data base containing values for each grid cell covering the property is created at the end of execution, if chosen as an option by the user. The Mine Coordinate Generator reads this information and creates a special direct access data set from the sequential data input. When information defining the mine grid is read, the values present in the property grid are for the interpolation of values for each mine block.

Jan 1, 1985

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

Lower workers' dust exposures during bag stacking while ergonomically improving the bag stacking process. Approach Install a new pallet loading dust control system which uses a push-pull ventilation technique along with a hydraulic lift table to control the pallet loading height throughout the entire loading cycle. How It Works A low-volume, high-velocity blower system operating at approximately at 120 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-inch air jets (approximately 1,200-ft/min velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they en-train dust generated during bag stacking. The dust laden air is then captured by the exhaust ventilation system which draws approximately 2,500 cfm through an exhaust hood on the opposite side of the pallet.

Jan 1, 1989

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By Clark F. Grain

The monoclinic to tetragonal inversion of zirconium dioxide was studied by single-crystal X-ray methods, high-temperature X-ray diffractometry, and differential thermal analysis. The unusual features of the inversion, such as no definite transition Lperature, hysteresis, and athermal kinetics, were confirmed for powders who mean crystallite size was greater than 1,000 A. Samples of mean crystallite size below 1,000 A displayed classical kinetics, obeying a logarithmic rate law. A detailed mechanism based on Ubbelohde's theory of continuous phase transformations was proposed which is consistent with all the experimental facts.

Jan 1, 1965

By A. W. Fahrenwald

Coarse sand flotation, both alone and in conjunction with gravity concentration, is a subject of research at the U. S. Bureau of Mines Field Office, Moscow, Idaho. One of the most important results of this work which is being carried out in cooperation with the University of Idaho, has been the development of a concentration process embodying flotation, classification, and tabling, in the order named. The flow sheet of the process is given in Figure 1. The type of feed desired for this process is coarser than is common in present "all flotation" practice, and is about the size of table feed.

Jan 1, 1929

By R. L. Grant

The conventional gallery test used by the Bureau of Mines Explosives Testing Station and corresponding establishments in other countries to establish the permissibility of explosives serves principally to differentiate the relatively safe explosive from the positively unsafe one. It has been recognized for many years that a more definitive test is needed to measure the relative incendivity to firedamp of explosives and explosive devices. A new method - the oxygen-value test - for measuring this incendivlty quantitatively has been devised and is being tested at Bruceton, Pa. To date, this testing bas been limited mainly to straight nitroglycerin dynamites. It is planned to study application of the method to permissible explosives in the near future. These results will be reported later. In the present report, permissible explosives will not be considered specifically.

Jan 1, 1954

By D. W. Butner

As a part of the Bureau of Mines program for the discovery and development of critical and essential mineral deposits, the Darwin district, Inyo County, Calif., was chosen for investigation as a possible source of, tungsten ore. Two properties were active in the district at the time. One was producing tungsten concentrate and the other was preparing to produce tungsten concentrate as a byproduct in the milling of lead-zinc ore. The objective of the project set up by the Bureau was to investigate promising areas and to sample, thoroughly those which preliminary inspection indicated contained tungsten ore. Work was begun November 17) 1941, and completed January 19, 1942. In the course of the project, 18 localities were inspected and 9 were sampled. The following pages brief the history, note the location, and outline the physical features and geology of the district. The work performed by the Bureau of Mines is described and supplemented with assay maps.

Jan 1, 1949

By I. AITKENS

Quartz maintains a rather conspicuous position among gem stones , despite its being the commonest and, in its natural form, the most easily recognized of mineral substances . This prominence is due primarily to the extensive use of amethyst , which provides stones of the finest violet color , and also to the wide employment of yellow quartz ( citrine ) which is called topaz by jewellers and vies with the true topaz in color and brilliance . Unlike many less costly gem materials quartz is hard and durable .

Mar 1, 1932

By R. R. Wells

This report summarizes the results of laboratory testing of copper-bearing magnetite ore from the Poorman, Bush & Brown, and Copper Center deposits, Kasaan Peninsula, Prince of Wales Island, southeastern Alaska. The ores contain minor amounts of chalcopyrite and pyrite. Intimate association of these sulfides with magnetite necessitates fine grinding for adequate liberation and rejection of copper and sulfur and for the production of high-grade iron concentrate low in objectionable impurities. Laboratory tests indicated that the optimum results can be obtained by flotation of ore ground to minus-100-mesh, with subsequent wet magnetic separation treatment of the flotation tailing. A summary of results obtained by this treatment of the three samples tested is shown in table 1.

Jan 1, 1957

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended' as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By L. C. IlsLey, R. A. Kearns

"The electrical section of the Bureau of Mines has obtained copies of all available State safety rules and regulations in order to make a study of those portions of the codes relating to electrical equipment. While it has been found almost impossible to compare the several codes as a whole, comparison of those regulations dealing with a single subject has proved both interesting and instructive.Sixteen states have rules or enactments having reference to telephones and the present paper covers a compilation of these references. It is believed that data of this kind will be of service to commissions or other bodies contemplating the revision of existing codes.The compilation taken from the various codes follows: State Rules and Regulations.California.Sec. 5 (Par. c) Telephone communication shall be maintained between a co-operative station and each mine which it supplies. If the foreman in charge of a station does not reside thereat, his residence also shall be in telephone communication with each mine supplied by his station.Sec. 8 (Par. a) Whenever a fatal accident occurs in or about any mine, notice thereof shall be given promptly by telephone or telegraph if possible, followed by a notice in writing to the chief inspector, by the superintendent or other person having immediate charge of the work at the time of the accident."

Jun 1, 1921

By F. R. Cattoir

This report presents the results of preliminary studies for the evaluation of some fused-salt electrolytes for refining tungsten metal, and describes the equipment used. Some impurities could be eliminated with electrolytes composed of sodium chloride, sodium iodide, or sodium tetraborate in combination with tungstic oxide or sodium tungstate. Electrolytes composed entirely of chlorides were unusable because of the volatility of tungsten chloride. Refining 96-to 98-percent tungsten to produce a commercial grade was more successful than further refining of 99.9-percent tungsten. No electrolyte tested yielded a product pure in all respects. Electrolyte temperatures of about 900° C were necessary to maintain a good dissolution rate at the anode and acceptable cell operation. Cathode current densities at the beginning of a deposition cycle were limited to approximately 1 ampere per square inch. Higher current densities resulted in a finely divided product that frequently failed to adhere to the cathode. The most conspicuous impurities in the tungsten produced were carbon, iron, and molybdenum; the former two came from the iron cell and the graphite cell liner. Electrolytes com-posed of tungstic oxide or sodium tungstate in sodium iodide, or 2Na, 0.B203, were capable of producing tungsten carbide.

Jan 1, 1963