Search Documents

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By Earl R. Maize

This is the first of a series of reports dealing with development of a method of strengthening bituminous-coal-mine roof. Later reports will describe the progress made with injecting high cohesive and adhesive bonding agents into bedding planes and mine tests of roof strata strengthened by the bonds formed. The concept of strengthening roof strata in coal mines by inserting steel rods in the form of bolts has been widely accepted by the coal industry. The benefits of increased production and safety derived from this type of roof support has more than justified the increased cost of roof bolting. However, not all coal-mine roof structure is amenable to this type of support, and failures occur owing to the heterogeneity and variable character of mine-roof strata.3/

Jan 1, 1957

By E. J. Gleim

In the movement of self-controlled direct-current machinery, particularly shortwall cutting, machines, from one place to another in coal mires, "nipping" or it stinging" has been practiced quite commonly. These terms refer to the method of obtaining current for propelling or tramming the machines along trolley haulageways by sliding the trolley trip (hook or nip), which terminates one conductor of the trailing cable, along the trolley wire. This is usually done by the machine operator or runner while sitting on the machine truck and holding the nip terminal against the trolley wire as the machine travels along the rails. This procedure is objectionable for several reasons. Under the best conditions, the area of contact between the nip and trolley wire is snail end, consequently, sparking and flashing ore most likely to be continuous as the machine proceeds. This is undesirable, not only because of the detrimental effect of electric flashes upon eyesight, but because of the pitting and roughening the trolley wheels which decrease the efficiency of current collection by locomotive trolley wheels and shoes and at the same time shorten their useful life by increased wear.

Jan 1, 1939

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970

By C. W. Dwiggins

This report describes the development, theory, and application of techniques and instruments for quantitatively determining nickel, vanadium, and iron in oils, using direct, X-ray emission spectrographic methods (5, 6).3 The methods developed apply to petroleum and other oils as well as some specific fractions of oils. The quantities of nickel, vanadium, and iron in various petroleums are of practical and theoretical interest. Even traces of nickel and vanadium may poison cracking catalysts, and X-ray methods have been used for determining nickel in such catalysts (7). At least parts of the nickel and vanadium occur as metal-porphyrin complexes, a fact which may have considerable bearing on knowledge of the origin of petroleum.

Jan 1, 1962

By G. R. Hopkins, A. B. Coons

A survey of the petroleum pipe lines by the Bureau of Mines as of May 1, 1923, shows that on that date there was a total of slightly more than 90,000 miles of pipe lines in the United States, having a capacity of approximately 15,750,000 barrels, which is equivalent to one-fourth of the nation's average production for one month. These lines varied in diameter from 2 to 16 inches, the weighted average being 6 inches. The total pipe-line milenge was about equally divided between trunk lines and gathering lines, though the capacity of the former was about four times that of the latter. This was due, of course, to the difference in average diameter, that for the former being 7.4 inches as compared with 3.7 inches for the latter. The common size for trunk lines was 8 inches, and for gathering lines 2 inches. Oklahora, with 19,180 miles of pipe lines, is the leading State in total mileage, with Texas second and Pennsylvania third. From point of trunk lines alone Texas is considerably ahead of any of the other States, a position which it owes to its size and to the growth in the rovement to its Gulf ports. Cali- fornia, though the leading State from point of production, ranks only seventh in pipe-line mileage. This is due to the fortunate location of the Los Angeles Basin fields, some of which are within sight of the refineries to which their oil is delivered or of the port of San Pedro through which their oil is shipped. The last survey of this nature, made in the spring of 1924 by the U. S. Geological Survey, recorded a total mileage of nearly 83,000 with a capacity of approximately 14,450,000 barrels. This indicates an increase of 9 per cent in both mileage and capacity during the two years.

Jan 1, 1927

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By B. J. Arnold, F. F. Aplan

"The captive bubble and sessile drop contact angle techniques have been used to evaluate the hydrophobicity of petrographically identified coal macerals. The magnitude of the contact angle on vitrinite is shown to be a function of coal rank ( %C, %0 and % vitrinite reflectance), increasing with increasing rank to a maximum for low volatile bituminous rank coals then decreasing for anthracite. The least data scatter is found when vitrinite reflectance is used as a rank parameter. Contact angles measured or estimated for other discrete macerals, indicate a variation in hydrophobicity based on coal type. These data correlate well with known flotation results. Coal is a heterogeneous mixture of plant remains and associated minerals that have undergone chemical and physical changes by biological and geological processes. These plant remains form coal macerals, discrete organic entities in the coal which have characteristic chemical and physical properties. As the differing chemical nature of each maceral will affect its behaviour in processes such as carbonization the separation of macerals during coal preparation may provide an important asset in coal utilization.Separation of some of the macerals based on specific gravity has been achieved in the laboratory, and by Sun and Cohen , in a study of two Pennsylvania bituminous coal preparation plants. It was indicated that the lighter exinites report almost exclusively to the clean coal while the denser inertinites are concentrated in the higher gravity fractions. The Longwy-Burstlein process6 took advantage of the difference in hardness or friability of the macerals by using impact breakage followed by screening to remove the more friable vitrain,clarain and fusain. The remaining durain, often high in spore content, was then recrushed. The re-mixed fractions produced the optimum size for obtaining the best coke strength for a particular coal.Separation or concentration of rnacerals by froth flotation largely depends on differences in the hydrophobicity of the macerals. Sun and Cohen 5 . indicated an order of decreasing floatability as exinite, vitrinite and inertinite, while a Russian study (as cited by Brown 7 ) showed that vitrains floated more readily than the duller types. More recently, Hirt and Aplan8 showed that 'pseudovitrinite' floats somewhat faster than does vitrinite while fusinite floats very slowly. Olson and A plan found that vitrinite floated easily while substantial quantities of the non-floated coal contained fusinitic material. Burdon noted that vitrinite is more floatable than semifusinite, and Sarker et a/. 11 have shown that vitrinite is selectively concentrated by froth flotation and oil agglomeration. Sun indicated that flotation, based on his calculated floatability index, should decrease in the order clarain, vitrain, fusain and durain; while Horsley and Smith 13 indicated the decrease to be: vitrain, clarain, durain and fusain. These differences can be attributed to the specific coals used in each study and to the individual macerals composing each coal type within a given coal."

Jan 1, 1989

By A. W. Ambrose

"Records of individual wells form the basis for the successful operation of any company engaged in the production of petroleum. The expense attached to the compilation of records is negligible in comparison with the benefits resulting from their use. There a company has not a complete system of records, immediate attention should be given to the preparation of forms upon which to collect data, and, to the collection of data for these forms. The records needed vary with each district, but for each field a set should be adopted that will best meet the needs of each property. Practically all operators, and particularly all successful operators, agree on the necessity of good records, shopping what the wells have done, are doing, and may be expected to do in the future. Any operator realizes the value of records of sales of oil and should place almost equal emphasis on the records of well logs and histories showing the east and present performances of wells. Indeed, trustworthy records are absolutely necessary for the proper operation of any oil or gas property.Complete records should be kept on each well from the time the location and elevation are determined until the well is abandoned, and the engineer should review old records often enough to be familiar with the past performance of the various wells and with the conditions that affect production. Some of the forms that may be prepared are:--"

Mar 1, 1920

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Herbert R. Appell

Urban refuse, cellulosic wastes, and sewage sludge have been converted to heavy oil by heating under pressure with carbon monoxide and steam. Conversions of the organic matter to oil, water, and gas have averaged near 90 percent at temperatures of 250° to 400° C and pressures of 1,500 to 5,000 psi. The yield of oil, based on the dry organic matter of the waste materials, is usually near 40 percent. This is the equivalent of more than 2 barrels of oil per ton of dry, ash-free waste material. The oil from urban refuse and cellulosic wastes has a sulfur content near 0.1 percent. This low sulfur content makes the oil from refuse a desirable source of fuel oil.

Jan 1, 1970

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By I. Iwasaki

In recent years the rapid depletion of high-grade iron ores and the demand by blast furnace operators for increasingly low-silica ores have stimulated interest in flotation studies of low-grade iron ores, such as wash-ore tailings and oxidized taconites. Four processes have been reported for the flotation separation of these iron ores--anionic and cationic collection of the iron oxides, cationic collection of siliceous gangue, and anionic collection of activated siliceous gangue (5).5/ The effectiveness of any one method, however, depends largely on the mineralogical composition and on the physical structure of the sample; hence, a comprehensive study of the floatability of the individual minerals occurring in these materials is essential. A review of the literature shows that the floatability of hematite and magnetite has been frequently investigated, whereas very little corresponding information is available for goethite, or for its more earthy form, limonite, both of which are abundant in the Mesabi and Cuyuna ores (19). The purpose of this investigation was to formulate general information on the floatability of goethite. Vacuum flotation, contact angle measurement, and simplified flotation tests using a modified Hallimond tube were used. The experimental results were correlated with the electrokinetic properties of goethite as determined by streaming potential measurement. The results were used to interpret the batch flotation tests made on an artificial mixture of quartz and goethite.

Jan 1, 1960

By Scott W. Hazen, Richard F. Link, George S. Koch

The Mi Vida mine , Big Indian district , San Juan County , Utah , is in an ore deposit of uranium and vanadium minerals disseminated in certain sedimentary beds of the Triassic Chinle formation . Statistical analysis of assays of samples taken from the ore body affords an estimate of the grade of the ore body and provides a prediction about the direction of best mineralization beyond the sampled area . The basic data analyzed are assay results for uranium ( Uз Og ) , vanadium (V₂O ) , and lime (CaO ) from 225 channel samples cut at 79 sample points . Through the use of appropriate statistical methods , particularly regression analysis , the grade of ore may be estimated more precisely than by conventional means , and the most favorable direction to extend the mine may be predicted . Frequency distributions of assay residuals for uranium , vanadium , and lime are compared to frequency distributions of assays without regard to trend . Correlations among these variables are obtained and interpreted . The statistical methods employed illustrate certain techniques that may be used to analyze assay data from ore deposits in general .

Jan 1, 1964

By J. P. McGee

A 1,000-hour test with a gas turbine at 1,200° F showed a working fluid of 1 gr of ash per 100 scf of power gas (79 percent of the ash 7 to 35 microns in diameter) to be excessive for acceptable blade wear for commercial practicability. Blades in the turbine consisted of about 20 percent each of chromium, cobalt, and nickel; 3 percent molybdenum; 2-1/2 percent tungsten; and smaller amounts of manganese, columbium, and tantalum. Erosion of both the fronts and backs of the turbine nozzles was particularly heavy, the trailing edges being worn to a featheredge. Erosion of the buckets was less marked, although the leading edges were somewhat pitted. A refractory-lined combustor performed efficiently and with little abrasion of the lining by the ash-laden gas.

Jan 1, 1969

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970