Search Documents

By J. B. Ligon

Blast induced stress waves, propagating along the surface of a drift of an underground hardrock mine, were recorded and analyzed. Resistance strain gages, accelerometers and a velocity pickup were used in making the measurements. Although a full face blast was recorded, the stress waves were initiated by single borehole blasts for the majority of the project. A special instrument trailer was designed, constructed and utilized during the project. A reliable strain wave transducer was developed for measuring the stress waves propagating on the drift surface. A correlation study between strain and acceleration signals for P-waves was made which agreed well with theory. The use of stemming was found to reduce strain and acceleration magnitudes as predicted.

Jan 1, 2011

By Paul M. Tyler

According to Lindgren , the economic importance of pegmatites stems from the fact that they represent the principal natural storehouse of two classes of mineral products : (1 ) common minerals in exceptional size and purity and ( 2 ) several of the rarest minerals , which are not commercially available from other types of deposits . Most pegmatites can be described simply as coarse- to very coarsegrained granites . Pegmatite includes coarse -textured igneous rocks of any composition , such as syenitic , alkali syenitic , dioritic , or gabbroitic ; but basic pegmatites are far less common than those that are associated with acid rocks and correspond approximately to the mineral composition of ordinary granite . Moreover , only a very few basic pegmatites can be considered as economic sources of useful minerals . Whereas , in ordinary granitic rocks the individual minerals usually measure 1/8 to 1/4 inch across , in pegmatites they are characteristically over 1 inch and often more than 12 inches in diameter . Although some of the constituents of the pegmatite may be only a fraction of an inch in length , single crystals more than 10 feet long are by no means unusual , and some crystals are enormous . A whole quarry was operated in the Urals within a single crystal of feldspar . Huge quartz crystals are quite common although usually imperfect . Muscovite plates 10 feet in diameter have been mined in India , and the Purdy mica mine in Canada contained a mica crystal measuring 6.5 by 9.5 feet and weighing nearly 7 tons , which supplied more than $20,000 worth of trimmed mica sheet . A loglike crystal of spodumene in the Etta mine in the Black Hills of South Dakota was 42 feet long . Giant crystals of beryl weighing several tons apiece have been mined from several properties . Because so many rare minerals are found in substantial concentration only in pegmatites , it is a common fallacy to suppose that pegmatites are always enriched in rare elements . Traces of most of these elements , of course , are found in almost all igneous rocks , and they reappear in the sediments derived from igneous rocks . It does not follow , however , that all or even most pegmatites contain higher percentages of rare elements than other granitic rocks . Geological evidence points to the probability that notable concentrations of rarer minerals or elements in pegmatites are more or less fortuituous , such additions often being ascribed to events subsequent to the original emplacement of the main body of the pegmatite . Most pegmatites consist principally of potash , feldspar , and quartz . Even mica , although commonly present , is not an essential constituent . Probably

Feb 1, 1950

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By Frank A. Peters

An evaluation is made of a lime-soda sinter process for extracting alumina from clay. In this process, alumina is extracted by sintering clay with soda ash and limestone and then leaching the sinter with a dilute sodium carbonate solution. The sodium aluminate solution formed during leaching is separated from the residue and treated with lime in autoclaves to remove dissolved silica before alumina trihydrate is precipitated with carbon dioxide. The tri-hydrate is then calcined to a-alumina. Two options, dry grinding and wet grinding, are used in the sintering step. The fixed capital costs for plants producing 1,000 tons of alumina per day are $72 million for the dry grinding option and $66 million for the wet grinding option on a Marshall and Stevens chemical equipment index basis of 240.0. Specific geographic locations of plant and raw material sources are not assigned, but, since this process requires large quantities of both lime-stone and clay, the plant site is considered as variable with relation to the clay mine and limestone quarry. A nomograph is given to find operating costs at various delivered costs of clay and limestone. If the plant is located nearer the limestone quarry so that the delivered cost of clay is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $76.47 and $71.61 per ton of alumina for the dry grinding and wet grinding options, respectively. On the other hand, if the plant is located nearer the clay mine so that the delivered cost of clay is $1 per ton and the delivered cost of limestone is $2 per ton, the operating costs are $80.15 for dry grinding and $75.34 for wet grinding.

Jan 1, 1967

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By E. G. King

Many of the rare-earth oxides are now commercially available in pure form and they have a variety of potential technical uses. Thermodynamic data for these oxides, however, are rather sparse. It is one of the functions of the Bureau of Mines to fill the need for this type of information. This report gives the results of low-temperature heat-capacity and high-temperature heat-content measurements by the Bureau of Mines of lanthanum sesquioxide. The entropy at 298.15° K. was evaluated and heat-content and entropy increments above 298.15° K. were obtained to 1,800° K. The results were combined with the known heat of formation at 298.15° K. to derive heats and free energies of formation at higher temperatures. Sufficient information is now available to permit reliable thermodynamic calculations involving lanthanum sesquioxide within the temperature range 298° to 2,000° K.

Jan 1, 1961

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971

By G. W. Jones

The Bureau of Mines has advocated the use of stenches as warning agents in metal mines and in gas-distribution systems since 1920 A considerable amount of research has been conducted on ethyl mercaptan and other compounds to determine their effectiveness when used for this purpose.4/5/6/7/8/9/10/11/12/13/ Miners are warned of danger by a stench injected, in measured quantity, into a compressed-air line through which it is rapidly carried to the working faces, where it escapes from the compressed-air equipment and imparts a characteristic odor to the air. This method is not applicable to mines where only a limited number of com-pressed-air lines are used, as for example, many coal mines; the ventilation currents available in these mines may be too slow for warning purposes.14/

Jan 1, 1954

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By Wallace W. Roepke

Research on coal cutting at the Bureau of Mines Twin Cities Research Center (TCRC) has evolved from a purely mechanical approach, specifically to reduce dust or frictional methane ignitions, into an understanding of the complexity of the cutting system relationships. Achieving an understanding of these relationships requires a wide variety of testing techniques and equipment. Laboratory facilities and the associated equipment exist for shallow to deep cutting in both coal and coal-inclusive rock with any desired bit type. Research efforts with this equipment are providing insight for significant advances to help solve the problems of pneumoconiosis and frictional ignition. This effort will ultimately affect both respirable dust and methane ignitions at the face through better bit design and will increase the salable percent of run-of-mine (ROM) coal processed. It will also affect the design of rotary-drum cutting continuous mining machines (CMM) and longwall machines. This report describes the main features of the coal cutting research facilities at TCRC.

Jan 1, 1983

By E. G. Erspamer

Laboratory investigations were made by the Bureau of Mines on ore containing the sulfides of both mercury and antimony to develop a method or methods for the economic recovery of mercury metal and the concurrent recovery of antimony as metal or salts,. If standard mercury-recovery techniques are applied to such ores, the antimony content interferes with the effective production of mercury metal; further-more, the antimony is lost. This report presents the results of tests on a sample of cinnabar-stibnite ore from the Red Devil mine near Sleitmute, Alaska. Red Devil ore was chosen for the investigation because it is purported to be typical of ores of the Kuskokwim River area, which, in their aggregate, constitute large potential reserves of mercury and antimony. Studies included petrographic, spectrographic, and chemical analyses, gravity-separation tests, bulk flotation of mercury and antimony sulfides, differential flotation, leaching, and furnacing of crude ore and of flotation concentrate.

Jan 1, 1956

By K. O. Bennington

Thermodynamic properties were determined by the Federal Bureau of Mines for lithium metasilicate (Li2Si03) and lithium disilicate (Li2Si205). Their enthalpies of formation were investigated by hydrofluoric acid solution calorimetry. The standard values are ?Hf°298 -393.8 ± 0.8 kcal/mole for Li2Si03, and ?Hf°298 -611.8 ± 1.0 kcal/mole for LiSi205. Enthalpy increments above 298 K were measured by copper-block drop calorimetry from 298 to 1,404 K for Li2Si03, and from 298 to 1,281 K for Li2Si205. Low-temperature heat capacities were determined adiabatically from 6 to 305 K for Li2Si205 only. The derived standard entropy is S°298 = 29.20 ± 0.10 cal/deg-mole. The various experimental data were combined with other data from the literature, and resulting properties of ?Hf°, ?Gf°, and log Kf were tabulated as a function of temperature.

Jan 1, 1976

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By Robert F. Holub

The U.S. Bureau of Mines (USBM) has tested a personal dosimeter for measuring radon decay products that is manufactured by Tom Scurry Associates. The tests were made to determine the accuracy of the dosimeter system for record keeping of radiation exposures to radon decay products encountered in mining. The radioactivity-detecting head is based on a design developed by the USBM, and the associated air pump was developed by the manufacturer. The dosimeter system was tested in the USBM radon chamber. The detecting head uses CaF:Dy thermoluminescent phosphors and is mounted on a self-regulating air pump. Batteries supply power sufficient for an 8-h shift. The dosimeter system is worn on the miner&apos;s belt. Dosimeter calibration tests were performed by the USBM. In addition, the pumps were tested and evaluated under continuous flow conditions. The results of these tests indicate that the Tom Scurry Associates Model DOSI600 dosimeter is suitable for general use in mines where record keeping for natural radiation exposure is required.

Jan 1, 1995

By R. H. Lien

The Bureau of Mines investigated nitrous oxide (N20) stability when used as a solvent for organic removal from metal powder surfaces. Both supercritical and subcritical conditions were studied. This investigation was prompted by the occurrence of a violent reaction when supercritical N20 was being used to deoil a metal powder grinding waste sample that contained 20 to 25 wt pct cutting oil. Tests were conducted to determine the cause of the reaction and to define stability limits. Test data showed that the waste&apos;s oil fraction reacted violently with N20 acting as an oxidizer; the metal powder acted as a promoter to reduce the ignition temperature. Although the data were scattered, this temperature appeared to reach a minimum at a certain pressure (dependent on vessel and sample size). The minimum ignition temperature for a 0.64-g sample in a 72-cm3 vessel was 360° C at 200 psig. As the sample size increased, the ignition temperature decreased. For example, when the sample size was increased to 10 g, a reaction occurred at 240° C and 600 psig. Because of the variability of ignition temperature with pressure and sample size, safe operating conditions were not established. Overall, this research showed that extreme caution should be exercised when using N20 in an organic or organic-metal system.

Jan 1, 2011