Search Documents

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By Victor Spironello

The Bureau of Mines is studying cupola ironmel technology with the objectives of conserving high-quality raw materials through substitution and productivity. In the research re-ported here, a ize was modified by a gas-fired melting and/or ing chamber into the stack above the level of the coke bed, for study as a prototype for a coal-fired melting chamber. The modified cupola, in which natural gas was used to partially replace foundry coke, was evaluated in several trial runs. Data were obtained on furnace performance, metal and slag chemistry, and scrubber waters as particulates. Results of the modified ion were compared to those of conventional cupola operation. Although this research was preliminary--since the ultimate goal is to use pulverized coal instead of yielded ample evidence that the melting rate of a cupola can be icantly increased with less than a increase in energy input. Other evidence suggests that melting of low-density scrap can be enhanced and that scrap containing undesirable and/or oxidizable elements can be appreciably upgraded. This work is continuing and will include the use of pulverized coal of low rank to assist in melting.

Jan 1, 1984

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By Lee M. Manna

This report summarizes the program to design, fabricate, install and preliminary test a pneumatic braking system for 10-ton mine haulage cars. Major arrangement drawings are reproduced, pneumatic schematics, parts list and actual developed costs. Recommendations as to system improvements are made.

Jan 1, 1977

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By R. E. Peterson

Scrap iron is partially oxidized at elevated temperatures in the selective oxidation process to produce iron oxide and a dense residual metal of high purity. Investigation of the process was confined to converting automobile hulks into useful products. In one test series, compressed, sheared automobile scrap was processed at 1,000° C in a 36-foot-long rotary kiln at feed rates ranging from 300 to 1,200 lb/hr. Less fuel was required to maintain the temperature at the higher feed rates because of the heat generated from the burning of the combustibles and the oxidation of the iron. The bulk density of the residual metal exceeded 75 pounds per cubic foot. In an attempt to lower the quantity of contaminants in the residual metal, another test was designed using automobile hulks which had been prepared by ripping, a low-cost method of scrap fragmentation. Before oxidizing the ripped scrap approximately 62 percent of the total copper was removed in a tumbling, screening, magnetic separation and hand-sorting system. Cast iron made from the residual metal obtained by selective oxidation contained 0.15 percent copper; iron oxide scale obtained from the kiln averaged 0.13 percent copper. Pellets made from the scale demonstrated compressive strengths necessary for blast furnace reduction; lead and zinc were removed by volatilization when the induration was performed in a reducing atmosphere.

Jan 1, 1972

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By F. N. Bender

Percolation leaching of wad-type manganese ores was investigated, using a novel system of alternate upward passage of sulfur dioxide gas through moistened ore and downward percolation of wash solutions to extract solubilized manganese. Bench and large-scale tests designed to simulate vat and heap leaching were made on four wad ores from Arizona and Nevada and on a pailomelane ore from Arizona. Three of the wad ores required prebaking at 500° to 600° C. to produce a permeable agglomerate that would not slake during percolation washing. The hard-type ore and one of the wad ores that contained a large amount of granular gangue did not require prior roasting. The deportment of the different ores toward leaching and percolation was studied with particular reference to the influence of the sulfur dioxide - oxygen ratio and the effect of gas dilution on the rate of manganese dissolution, dithionate formation, and acid production. Crushed charges of the ores, as coarse as 1 inch and as fine as 1/4 inch, were treated for periods of 5 to 11 days. Percolation of the gas and leach solutions through the charges was achieved without difficulty. The manganese extractions varied between 78 and 97 percent and depended upon the size and type of ore leached. The average quantity of sulfur dioxide required in the larger scale tests was about 2.6 pounds per pound of manganese recovered. The dithionate formation varied from 0.35 to 0.9 pound per pound of manganese extracted depending upon the strength of leaching gas.

Jan 1, 1957

By J. W. Eckerd

The crushing of chestnut-size (1-5/8 by 13/16 inch) Pennsylvania anthracite in four commercial crushers (impact) jaw) hammer-mill) and gyratory types) was studied by the Bureau of Mines to determine which could produce the largest proportions of buckwheat Nos. 1 and 2 sizes (9/16 by 3/16 inch). Single pass dry and wet crushing techniques and the effect of stage crushing were evaluated. Calculations were made to show the effect of closed-circuit reduction on production rates and yield of the various sizes. The data show that the gyratory crushers produced the greatest percentage of the desired sizes. A ring-type hammer mill produced the greatest tonnage of buckwheat No.1 and rice (14.9 tons per hr.) during dry grinding tests) but the yield of these sizes was only about 55 percent) as compared with 62 to 70 percent for the gyratory crushers. The impact and jaw crushers produced the smallest amount of buckwheat and rice and the largest quantity of oversize material.

Jan 1, 1960

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By Ronald S. Conti

The Bureau of Mines conducted a comprehensive laboratory study of the thermal ignitability of various carbonaceous dust clouds with particular emphasis on various ranks of coal dust. The tests were conducted using a new 1.2-L furnace. Autoignition temperatures of dust clouds were obtained as a function of coal volatility and particle size. Dust particles and gas samples were collected by a rapid-sampling system in order to study the reactions involved in preignition and postignition processes. The autoignition temperatures measured in the new 1.2-L furnace were significantly lower and therefore more conservative than those measured previously in the Godbert-Greenwald furnace. The combined effects of thermal and electrical ignition of dust clouds were also studied in the 1.2-L furnace using electrical discharges of varying energies at ambient and elevated temperatures. The minimum spark energy necessary to ignite a dust cloud decreased significantly as the temperature of the dust cloud increased.

Jan 1, 1983

By G. R. Hopkins

According to reports as of January 1, 1931, the total daily charging capacity of the cracking plants, hoth completed and under construction, in the United States amounted to 1,950,781 "barrels, an increase over the previous year of 14 per cent. The total daily capacity of the operating plants amounted to 1,594,990 "barrels, or 82 per cent of the grand total, the capacity of the in¬ operative plants was 244,661 "barrels, or 12 per cent of the total, while the capacity of the plants under construction amounted to 111,130 "barrels, or 6 per cent. In comparison with a year ago, these data indicate a decline in the total capacity of the plants "being "built "but show material increases in the capacity of "both the other two classes. The increase in total inoperative capacity and the decline in construction in 1930 undoubtedly resulted from un¬ satisfactory economic conditions. The total number of cracking units completed or under construction on January 1, 1931, totaled 1,863 as compared with 2,002 the previous year and with a high of 2,559 on June 1, 1926. During the period between June 1, 1926, and January 1, 1931, the total charging capacity of the cracking plants has more than doubled, but the number of units has shown a material decline. This condi¬ tion has been brought about largely through the dismantling of many Burton still of small capacity and through the tendency to increase the size of the new units The "largest unit that can be identified in this survey has a daily charging capacity of 10,000 barrels, but undoubtedly there are some that would exceed this in size. Texas, with a total of 575,300 barrels, ranked far ahead of the other States in charging capacity, and was followed in order by California, Indiana, Oklahoma, and Pennsylvania. Indiana, with only five refineries, ranked third in cracking capacity, which illustrates the importance of the Chicago district as a gasoline-producing center. Not all of the States showed a gain in capacity during the year; in fact, four of them, namely Illinois, Louisiana, New York, and Oklahoma, reported a decline.

Jun 1, 1931

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By Oliver Bowles

The manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous industries. The use of lime by the building trades, in agriculture, and in hundreds of manufacturing and chemical processes has created demands for a large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of lime is an extensive one, but for the most part each publication has dealt with only certain operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has rendered valuable assistance in furnishing data for certain sections. Publications containing more detailed information on the various branches of the industry are referred to in the footnotes and in the bibliography.

Jan 1, 1936

By F. D. Cannon

"In metal and nonmetallic mineral mines during the 15-year period 1911 to 1925, 30.17 per cent of all fatalities and 16.57 per cent of all injuries were caused by falls of rock or ore from the back or roof or from the wail; 1.24 per cent of the fatalities and 11.05 per cent of the injuries were caused by rock or ore while loading at the working face; 6.66 per cent of the .fatalities and 2.49 per cent of the injuries resulted from men falling down 3 chute, winze, raise, or stope; and run of ore from chute or pocket caused 1.48 per cent of the fatalities and 1.93 per cent of the injuries.3 Hence, accidents due to falls of men and material caused. 39.55 per cent of the fatalities and 34.05 per cent of the injuries in these mines. Accident prevention can best be assisted by each company's preserving complete records of accidents classified according to cause and rate per thousand or 10,000 shifts. A systematic method of recording accidents and the employment of graphs or charts will be helpful to the company safety department in analyzing the cruses of accidents. The purpose of this publication is to analyze data on accidents caused by falls of men and material in metal -mines of the United States, and to suggest methods of preventing or reducing such accidents."

Jun 1, 1929

By William M. Knuth

The objectives of this study were the evaluation of the technical and economical feasibility of utilizing color and color infrared aerial photography to satisfy some informational needs for pre-mine planning, mine progress monitoring, and reclamation monitoring. Seven aerial data collection missions were conducted within a two year period over strip mine sites in Pennsylvania. Scales of 1:6,000; 1:12,000; 1:24,000; and 1:48,000 were flown on the first aerial mission. The 1:12,000 was chosen as the optimal scale for the remaining six flights. An extensive literature and legislative review and discussions with strip mine operators identified the informational parameters that could possibly be obtained from aerial photography. Interpretability accuracies were evaluated for parameters in the broad categories of land use, soils, water, vegetation, and geology. Seasonal interpretation characteristics were noted for infrared photography. Man hours for photointerpretation and costs of aerial data collection were monitored closely and incorporated into a cost benefit analysis. Those parameters that could be mapped, identified, or measured with accuracies =75 percent were incorporated into a photointerpretation training manual. An additional analysis was performed to determine the applicability of the interpretation methodologies and results developed for Eastern sites to Western surface coal mining sites. In addition, a separate aerial photographic interpretation manual was produced during this contract. It is intended to be utilized by eastern and midwestern surface mine operators and regulatory personnel.

Jan 1, 1978

By Herman W. Sheffer

This report describes and discusses present-day leaching technology employed to recover copper from low-grade mine and dump materials derived from the exploitation of copper ore deposits in the Western United States. Illustrations of the integral parts of the leaching, precipitation, and recovery operations at several copper-producing companies are presented. Schematic drawings are included to present typical flowsheets of leaching and precipitation operations. Operational problems common to most copper leaching and precipitation plants are discussed. Areas of present and future research to improve leaching techniques are cited.

Jan 1, 1968

By Thomas J. Peters

The King Mountain study area is centered about 120 air km northwest of Blackfoot, and 30 air km north of Arco, Idaho. The study area makes up the southern one-third of the northwest-trending Lost River Range--the highest mountain range in Idaho. The area is predominantly underlain by Paleozoic-age marine limestone and lesser dolostone, with a relatively small inlier of silica-rich, Ordovician-age quartzite. There are vast, unquantified resources of these industrial minerals present; however, special markets need to be developed for these resources which are near enough for transportation costs to be competitive. Five prospects were found in the study area; however, only one, the Elbow quartz silica prospect, contains resources and current claims. There has been no mineral production in the study area.

Jan 1, 1993