Search Documents

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By S. P. Holt, Robert S. Sanford

"INTRODUCTION The wartime demand for iron ore and alloy steel on the west coast revived interest in iron reserves in western United States and Alaska. Magnetite was known to have been the most abundant metallic mineral at some of the old copper mines on Prince of Wales Island. In the summer of 1942, the Bureau of Mines began a program of preliminary investigation followed by core-drilling two magnetite deposits on the island.The Poor Man iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by Robert L. Thorne, associate mining engineer of the Bureau of Mines, and John C. Reed and B. N. Goddard, geologists of the Federal Geological Survey in September 1942 the area was mapped geologically and a magnetic survey was made by the Geological Survey. In October and November 1942, a more thorough preliminary examination, which included cleaning out and sampling old adits and trenches, was made by thesenior author, Robert L. Thorne, and Aner W. Erickson, engineers of the Bureau. J. G. Shepherd, a consultant of the Bureau, spent two weeks in March and April 1943 investigating the Poor Man and other deposits on Kasaan Peninsula. Core drilling was completed in June 1943.L. A. Warner, of the Geological Survey, examined all cores and interpreted structural data revealed by the drilling."

Oct 1, 1946

By Thomas Varley

"The literature on flotation of oxidized ores except for patents (especially for reagents) is very sparse. The Bureau of Mines in 1936, published a circular on the subject, by Ralston and Allen. The treatment of oxides by flotation was then in its infancy, but several of the most important mining companies in the Western United States and Mexico are now operating flotation plants for treating oxidized ores. The purpose of this present circular is to review the progress made and bring the subject up to date. One of the writers of the 1916 report (Mr. Allen) has been associated with some of the most important mining companies who have put into practical operation the process of flotation of oxidized ores; among these companies are the Shhttuck Arizona Copper Co., Bisbee, Arizona (now the Shattuck Denn Co.) and the San Francisco Mines of Mexico, Ltd., San Francisco Del Oro, Chihuahua, Mexico. His experience and other sources of information have been freely drawn on in pre-paring this paper. Mr. Ralston, assistant chief metallurgist of the Bureau of Mines, contributed many valuable suggestions and criticisms.Sulphidizing Reagents for Oxidize Ores.The various reagents and methods that might possibly be used for sulphidizing were summarized by Ralston and Allen as follows:""Sulphidizing (1) by the use of hydrogen sulphide on either the dry or the wet crushed ore, (2) by the use of solutions of the various sulphides and sulpho-compounds of sodium, (3) by the use of solutions of the various sulphides and sulpho-compounds of calcium, (4) by the use of sulphur vapor, (5) by the use of a sulphureted oil, (6) with colloidal sulphur."

Jun 1, 1927

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By Ronald T. Mayerle

In 1989, the U.S. Bureau of Mines conducted a mineral investigation of the Mallard study area near Elk City, Idaho. The study area comprises most of the original Mallard RARE II area (1-847) plus some additional lands. The investigation is part of an ongoing, multi-year study of north-central Idaho that is being conducted in cooperation with the Idaho Geological Survey and the U.S. Geological Survey (USGS). The only identified resources are rock suitable for road metal. Five lode prospects and a pyrite-bearing rock quarry, which is operated by the Forest Service for aggregate, were examined for metals. One of the prospects warrants additional exploration for silver in quartz veins, but the chance of finding an economically minable deposit is limited. Several rock and stream sediment samples were anomalous in various metals. Two of the more promising localities for gold and/or other metals are adjacent to a unit of the Frank Church-River of No Return Wilderness that the USGS classified as having a moderate potential for gold deposits related to fossil hot springs.

Jan 1, 1991

By George H. Popper

The Bureau of Mines has evaluated the extent of phosphate resources available for recovery by the experimental borehole mining method in the Southeastern Coastal Plain of the United States- Phosphate re- sources at overburden depths greater than 30 m are as a rule currently unsuitable for recovery through conventional mining methods because of economic, environmental, or technical considerations. In the identified deposit areas, borehole mining operations are projected to yield a more favorable rate of return and to be environmentally more desirable than conventional surface mining. Borehole mining resource estimates presented in this study are preliminary and designed to serve as a basis for future resource evaluations, as the current data base is relatively sparse and incomplete. The resulting resources have, therefore, been classified as hypothetical and speculative and are subject to up- dating as additional exploratory data become available. Hypothetical and speculative resources amenable to borehole mining are estimated to total about 385 billion metric tons (rat) of phosphate matrix with a minimum in situ grade of 5 pct P205. With projected borehole mining capabilities and current conventional beneficiation procedures, this resource would make available approximately 64 billion mt of phosphate rock product at an estimated grade of 30 pct P205.

Jan 1, 1985

By M. M. Kirk

Forced-air cooling of cold-mold arc furnaces for melting zirconium and similar metals has been investigated and found to be practical from the stand-point of heat transfer. It is believed that this technique offers a significant reduction in explosion hazard from that inherent in water cooling, the current industrial practice. A copper crucible, with longitudinal, integral-type fins and with an outer jacket to confine the airstream, appears to be the best general design for air-cooled operation. Cutting the fins into short segments and bending the segments to produce a herringbone effect increased the airstream's turbulence and was found, on test, to increase the heat transfer up to 35 percent.

Jan 1, 1959

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

In 2005, a total of 263 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.8% of all mining operations. ? Gold mines comprised 46.0% (n=121) of all metal mining operations. Other common types of metal mines were iron ore (n=32; 12.2%), copper ore (n=31; 11.8%), and lead and/or zinc ore (n=16; 6.1%). ? Nevada had the largest number of metal mines (n=52; 19.8%), followed by Alaska (n=27; 10.3%).

Jan 1, 2008

By Robert L. Skaggs

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were re- viewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation, (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrC14. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.

Jan 1, 1984

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By R. L. Thorne

The Snettisham Peninsula, 30 miles southeast of Juneau, Alaska, was studied by the Bureau of Hines to obtain basic information about the size, grade, and metallurgical characteristics of a large basic intrusive containing titaniferous magnetite. The investigation, which was part of a continuing program to determine the potential reserves of iron and titanium ores in Alaska, included transit and magnetometer surveys, followed by diamond core drilling and metallurgical testing. The magnetic attraction of a part of the Snettisharn Peninsula is noted on early navigational charts prepared by the Coast and Geodetic Survey. Reconnaissance examinations by the Geological Survey and a preliminary dip needle survey by the Territorial Department of Mines indicated the general nature of the basic intrusive, but little was known as to the grade and extent of the magnetite mineralization. The detailed survey by the Bureau of Mines proved an area of approximately 390 acres in which generally high magnetic anomalies with exceptionally high localized anomalies occur. Subsequent drilling across B representative section of the deposit yielded core samples, which assayed from 11 percent to over 45 percent total iron. A large sample of core composited to represent the drilled portion of the de-posit assayed 18.9 percent Fe, 2.6 percent Ti02, and 0.29 percent S, 0.32 percent P, and 0.05 percent v.

Jan 1, 1956

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By T. E. Gray

This report describes preparation characteristics of the significant coalbeds in Marion County, W. Va., as determined by the Bureau of Mines. It is one in a series telling what coals are suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.4 million tons of coal was produced in Marion County, W. Va., in 1958, of which almost 6 million tons was cleaned mechanically in nine cleaning plants. All of the coal mechanically cleaned came from the Pittsburgh bed. The Bureau of Mines estimated that 1,578 million tons of recoverable coal remained in the county in beds 28 inches or more thick as of January 1, 1955.

Jan 1, 1960