Search Documents

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,' the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By C. J. Wilhelm, John M. Devine

"Hydrogen aulphide associated with natural as was noted as early as at Point Albino, Canada. 4 The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence ma by no means common. However, in recent years, with the development of the producing zones of west Texas and the Texas Panhandle the production of ""sour"" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor-frequently a major problem—in the drilling and operation of any wells in those areas.The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen sulphide. From the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. 5 Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.6"

Sep 1, 1931

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By R. J. Gunderman

Explosionproof electrical enclosures for coal mine face equipment have been of the same basic design for many years without significant change. Characteristics for potential improvement were investigated through interviews, visits to mines and studies. Improved safety, health and productivity were the goals. Areas identified for improvement included rapid venting of pressure build-up due to an internal explosion, quick and easy entry or removal of cable entrances, and a quick and easy cover removal for rapid component access. Concepts were identified and evaluated, and the more promising devices were fabricated and tested. Encouraging results from initial tests led to further design refinement and establishment of design guidelines. These design guidelines for a pressure vent and for an elastomeric grommet type cable entry are described along with the testing used. An application for an experimental permit was requested from MSHA. After test and evaluation experimental permit #396 for evaluation in an underground coal mine was granted.

Jan 1, 1980

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By Eugene T. Sheridan

The 22d annual survey of the packaged-fuel industry by the Bureau of Mines, United States Department of the Interior, revealed that 26 plants in 8 States were in operation and reported production in 1956. The demand for packaged fuel in the United States has declined gradually since the end of World War II, and the number of operating plants has decreased from 70 in 1946 to 26 in 1956. Annual productive capacity of the industry has decreased also during this period, and the decrease in capacity was about proportional to the decrease in operating plants. Packaged-fuel plants are relatively small, and 85 percent of the active plants in 1956 had an annual capacity of less than 10,000 tons. The same situation prevailed in 1946, when 84 percent of the plants had a capacity of less than 10,000 tons. Total capacity for the 26 active plants in 1956 was 174,600 tons, an average of 6,715 tons per plant. Operating rates in 1956 were the highest since 1951, and the rate of production for the industry averaged 37 percent of capacity.

Jan 1, 1958

By H. -F. Krausse

Roof failures in underground coal mines are related to the lithology and geologic structure of the roof. There are two distinct suites of roof rock above the Herrin (No. 6) Coal in Illinois, and each has distinctive patterns of structure and roof failure. In black shale-limestone roof areas, roof instability is correlated with thinning of limestone beds and presence of faults and clay dikes. In gray shale roof regions, the prime roof hazards are posed by rolls, shear bodies, and presence of coal or carbonaceous partings in the roof. Most structural features examined are believed to have formed during early stages of sediment diagenesis and compaction. Structural trends and lithologic patterns are strongly interdependent for this reason. In many cases geologic patterns are so complex and locally variable that prediction of roof stability far in advance of mining is difficult. The need for greater flexibility in roof control planning is apparent.

Jan 1, 1979

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By W. P. Yang, L. B. Berger, G. W. Jones

"Any burning carbonaceous material, unless supplied with enough oxygen for complete combustion, will liberate carbon monoxide. Since tobacco in its many different forms consists largely of carbonaceous material, and duo to the conditions under which it is smoked (burned), carbon monoxide should be liberated. That this is true has been shown by Armstrong.***** who found that undiluted smoke from cigars contained in some tests more than 3.00 per cent carbon monoxide, the amount present depending upon the size and closeness of packing of the tobacco during manufacture and on the rate of burning.****** Cigarets gave much less CO, varying from 0.06 to 1.40 per cent. The rate of consumption and carbon content of the tobacco are not g.ven, so that a correlation of the values reported to conditions in closed spaces where people might be assembled are difficult, if not impossible.The Bureau of Mines is interested in the general question of carbon-monoxide hazards from tobacco smoke, mainly with regard to mine ventilation. In non-gaseous mines, especially metal mines, the question arises, whether, if groups of miners are permitted to smoke while working at unventilated faces or entries, would the accumulation of tobacco smoke in these places create an' additional hazards the to carbon-monoxide poisoning. The results should, in addition be of general interest in connection with ventilation of building and inclosed places where people may be assembled and smoking is permitted. The investigation described in this report was made with the above idea in view."

Oct 1, 1923

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By W. W. Adams, T. D. Lawrence

"The National Safety Competition of 1938, the fourteenth of its kind conducted by the Bureau of Mines in which bronze trophies known as Sentinels of Safety are awarded to winning companies, has just been completed and the results are presented here.With 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost-time accidents occurred during the contest year.The Sentinels of Safety trophies, provided by The Explosives Engineer magazine, were awarded to four underground mines, one open-pit mine, and one quarry. Each employee of the winning plant was awarded a Certificate of Honor by the Bureau of Mines in recognition of the employee's part in helping his company to win the trophy. In addition to the award of trophies, a Certificate of Honorable Mention was awarded to each of the mines and quarries in second, third, fourth, and fifth places in their respective contest groups and also to each mine and quarry that worked 30,000 or more man-hours without a lost-time accident. Ninety-two such certificates were awarded for 1938. Twenty-three other mines and quarries also operated without an accident but worked less than 30,000 man-hours, the minimum required by the contest rules for award of Certificates of Honorable Mention.Previous to 1938, five trophies were awarded annually in the National Safety Competition. For the 1938 contest a sixth trophy was provided by The Explosives Engineer so that open-pit mines and quarries, two classes of operations that previously had been included in one group in the competition, might have separate awards."

Aug 1, 1939

6784. Barnes, V. L., and Romberg, Frederick. Gravity and Magnetic Observations on Iron Mountain Magnetite Deposit, Llano County, Tex. Geophysics, Menasha, Wis., vol. 8, No. 1, 1943, pp. 32-45. An outcrop of magnetite in the Central Mineral region of Texas is explored experimentally with a dip needle and a gravity meter. Two anomalies are observed, one due to the outcropping body and one probably due to a previously unknown body close to the outcrop. The possible attitudes of the bodies are discussed, and their masses and probable dimensions are computed from the gravitational observations. - Author's abstract.

Jan 1, 1943

By Hon-Yim Ko

The properties of coal from the Pittsburgh seam, procured from the Bruceton and Federal No. 2 Mines were found to be similar. Strength and stiffness properties of Beehive Mine coal were determined and the material found to be isotropic. Mechanical, index and geologic properties of roof and floor coal measure rocks from Beehive mines were measured and correlated. Analytic formulations are given for coal creep under uniaxial loading, while triaxial creep is being investigated. Results of testing of coal model structures are compared with predictions from using several material models.

Jan 1, 1976

By F. B. TOUCH

This bulletin deals with a topic that is exceedingly wide, and will doubtl~ be under consideration and discussion so long as there are enough known deposits of oil and gas remaining in the earth to make their revelopment profitable. The Bureau of Mines has repeatedly called attention to the importance of protecting oil or gas sands from the encroachment of water, and the purpose of this paper is to summarize existing knowledge of methods and devices. Water may gain access to an oil-bearing formation from several sources-from water sands above or below those. containing the oil, or by encroaching through the oil sands as the oil is withdrawn. In short, it may enter a well from the "top, bottom, or side." Such ingress of water is a most serious detriment to the recovery of oil from the ground. As the art of drilling and developing oil properties has progressed, increasing thought, labor, and money have been expended on various methods, devices, and equipment for arresting the migration of water from its normal subsurface position into the porous strata containing valuable oil or gas accumulations. At an early stage in the oil-field development of California, it became evident that considerable modification of accepted drilling practices was necessary in order to meet the conditions imposed by the poorly consolidated shale, clay, sand, and bowlder beds penetrated, as well as the hard layers of sandstone and calcareous shale, which vary greatly in thickness, hardness, and frequency. These hard streaks are commonly called " shell," and are so reported in the well logs. As deeper and deeper territory was prospected, drillers from the older fields of the Ea,st, as well as from Texas and Louisiana fields, took part in the operations. Xhe practice evolved was thus based on the wide experience of a most cosmopolitan group of men who, considered as a group, were not hampered by being limited to the knowledge of the practice at any one locality.

Jan 1, 1918

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950