Search Documents

By E. R. Spencer, E. Reeves

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

By L. R. Herrmann

The research described in this report is the first phase of a comprehensive program for the development of a characterization for the structural properties of rock masses. The mathematical expression of the characterization is especial' tailored for use in conjunction with modern structural analysis procedures. The objective of the first phase of the project is to determine the feasibility of representing the structural properties of rock masses in terms of the analysis of an appropriate "representative volume" the results of this investigation are described in detail in the body of the report. The current state-of-the-art concerning the understanding and description of the fundamental mechanisms of rock behavior are determined from a survey of existing literature. The development of a representative volume that captures the most important of these mechanisms is described, In order not to unduly obscure the fundamental aspects of this development, the mathematical analysis of the representative volume is limited to plane strain conditions. A subroutine for the numerical evaluation of the proposed model (i.e., the analysis of the representative volume) is presented. The steps necessary for the incorporation of the subroutine directly into existing two-dimensional finite element structural analysis programs are described. Comparisons between the predictions of the proposed characterization and published results of simple laboratory tests are presented and discussed. Finally recommendations are given concerning suggested improvements of the model and the extension of it to the general three-dimensional case.

Jan 1, 1974

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Occupational noise-induced hearing loss continues to be one of the most pervasive health problems in the mining industry, despite over 25 years of regulation. One of the loudest pieces of equipment used in underground mining is the continuous mining machine. Noise sample data collected by the Mine Safety and Health Administration indicate that 42% of noise overexposures between 2000 and 2005 involved continuous mining machine operators. Previously conducted field and laboratory tests have determined that the continuous mining machine conveyor system is a dominant noise source. Loud impacts occur as the conveyor chain flight bars, used to move the mined aggregate, traverse their path from the top to the underside of the conveyor deck. Various noise control treatments have been applied to abate noise caused by the conveyor system. A durable polyurethane coating has been developed for the conveyor flight bars, resulting in a time-weighted average reduction of 3 dB(A) for an eight-hour work shift. In an attempt to further reduce continuous mining machine operator overexposures, a similar urethane coating has been applied to the tail roller component of the conveyor system. Laboratory results showed a 2 dB(A) reduction in sound power levels, but the component failed during underground durability testing. An outer steel sleeve has been added to the urethane coating of the tail roller to enhance wear resistance during mining. The urethane jacketed tail roller is the latest effort, combined with previous noise treatments, to bring the continuous mining machine into compliance with federal noise regulations.

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By P. R. Jones

The Bureau of Mines has written a computer program for the design and cost of a shell and tube type heat exchanger, in which a change in phase occurs on the shell side. The total cost, which was minimized, includes the annual fixed charges and annual operating costs. The program was written to meet the following requirements: (1) Triangular pitch, (2) single or multiple pass, and (3) heating or cooling. Price optimum design was obtained for four standard tube diameters and pitch. Standard heat exchangers whose area equaled or exceeded the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By Richard Lusignea

A single boom roof bolting machine was outfitted with measurement and recording systems for detecting changes in machine parameters while drilling. The purpose of this instrumented bolter or "smart drill" is to detect changes in roof conditions from the machine parameters of penetration rate, thrust, rotation rate, torque, rejected light from rock cuttings, and vibration of the roof during drilling. The system was demonstrated underground in coal mine conditions and showed correlation between rock type and drilling parameters.

Jan 1, 1982

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By C. A. Herbert

During the fiscal year ended September 30, 1932, there were 27 fatalities in the coal mines of Indiana. Four of this number occurred in small mines employing less than 10 men, over which the State Inspection Department has no jurisdiction. In addition to these coal mine fatalities, an explosives accident in a clay mine resulted fatally to one man. Tables 1 and 2, which follow, list the fatalities as to cause and occupation. Table 1. - Fatal accidents by cause, fiscal year ended September 30, 1932 [ ]

Jan 1, 1933

By Aleksandar D. Bugarski, Robert J. Timko

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

By T. A. Lang

Concepts and equations have been developed to quantitatively determine the stability of a rock bolted coal mine roof as a structural (beam-arch) member consisting of reinforced rock units. The equations take into account: rock bolt tension, length, spacing, and orientation; size of opening, strength and physical properties of the rock; and loads from distressed rock, and were critically reviewed using sensitivity analyses and the results available from relevant previous analytical and physical model investigations. It is concluded that they can essentially be validated by using small scale physical models and the full size mine entry model at the USBM Spokane Research Center. However, a comprehensive research program, including analytical and laboratory investigations and field trials in typical mines, will be required to define and validate criteria and standards for using the equations as a basis for a rational design code for rock reinforcement installations to replace the semi-empirical rules now being used. For example, these studies have shown that the practice of installing vertical roof bolts with a uniform spacing equal to the bolt length is inherently unsafe and that the spacing should be reduced near the walls to prevent shear failure of the roof strata. The development of such a rational design code would provide enhanced safety in coal mining operations and warrants a high priority in the Bureau's ground control research program.

Jan 1, 1981

By J. P. BONARDI, C. W. Davis, R. B. Moore, J. W. MARDEN, S. C. Lind, J. E. Conley

The rare metals are becoming increasingly important to our industries. Rare-metal alloys have properties which indicate that we are only on the threshold of the possibilities of their utilization, not only in making nonferrous alloys, but also as special steels. Not only are their uses broadening rapidly, but the metals are affecting our industries in other ways. The oxides and some salts are used as pigments; others have medicinal value. The pure metals are made into filaments for incandescent lamps, and targets for X-ray tubes. By their efficient use in alloys, the weight of automobiles is reduced, • and the wear and tear on tires and roads is thus minimized; in machine shops they help to give greater efficiency to tools and reduce production costs. Their development has marked a milestone in the progress of civilization. There has been considerable uncertainty regarding analytical methods for the rare metals. A great deal has been published, but the weak and the strong points of the various methods have not been investigated as carefully as is needed. The Bureau of Mines at its Rare Metals station in Colorado necessarily had to do a great deal of analytical work in connection with the metals covered by this bulletin, which aims to give the results of the experience so acquired. No claim for much originality is made, although some published methods given have been modified, and some new ones have been developed by members of the staff. The principal methods available were studied critically, and it is to be hoped that the work will assist those interested in analytical work in connection with the metals named.

Jan 1, 1923

By Jennifer A. Slatnick

Chlorofluorocarbons (CFC's), once universally accepted as ideal compounds for use in cooling and refrigeration, in foam production, and in cleaning electronic components, are being phased out and eventually banned under extensive international agreements because the chlorine in CFC's is thought to deplete the Earth's ozone layer. The industry has responded with the introduction of alternatives in the form of hydrofluorocarbons (HFC's), which contain no chlorine, and with hydrochlorofluorocarbons (HCFC's), which fill an intermediate gap in the replacement of CFC's. As a result of the elimination of chlorine in the HFC's and the reduction of it in the HCFC's, these alternatives contain more fluorine than the CFC's do. Other nonfluorocarbon substitutes, known as not-in-kind alternatives, contain no fluorine at all. As a result, the fluorspar mining industry, which is the source of fluorine in fluorocarbons through intermediate hydrofluoric acid, is being affected. Concern for this impact has led the U.S. Bureau of Mines to employ its capabilities to analyze various scenarios in the evolution of CFC replacements and substitutes to determine their effect on fluorspar mining. This report utilizes a network flow model to examine the effects of proposed replacements for CFC's, in terms of fluorine content, on fluorspar operations worldwide and on hydrofluoric acid plants in North America and Europe.

Jan 1, 1994

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

By A. Monomakhoff

If a conductor traversed by an electric current is broken, a conduction forms in the air between the two broken ends of the wire. This conduction manifests itself in an initial phase by an electric spark and, in a second phase, by an arc if the the circuit continues to supply sufficient power. This arc goes out when the distance between the two ends of the conductor becomes sufficiently large. If the break occurs in an explosive atmosphere, the energy contributed by the arc can cause an explosion. To avoid such accidents, electric circuits that may be utilized in hazardous atmospheres can be made "intrinsically safe". The investigation which we conducted is part of a research project on the intrinsic safety of arcs of high intensity but short duration, in the case of resistive circuits. We developed an electronic system which makes it possible to limit the duration of an arc at the level of the break of a conductor traversed by a current with a possible maximum intensity of 80 amperes. This experimental device for monitoring and measuring the parameters of the arc has shown that arcs of high intensity but with a duration limited to a few microseconds do not ignite an explosive methane-air mixture.

Jan 1, 1975

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By Matthew J. Sheridan

The Bureau of Mines study described in this report was conducted in the Denver, Colo., area (1) to summarize existing conservation practices as related to the most beneficial utilization of deposits of sand and gravel; (2) to identify the conflicting positions of the aggregate producer, the mineral owner, nearby residents, and local government officials responsible for determining land status and for issuing operating permits; and (3) to show the need for planning in Denver and in other expanding communities toward obtaining the benefits of conservation of our rapidly dwindling mineral resources. In order to determine the effects of urbanization on the Denver aggregate industry, interviews were held with owners of sand and gravel operations, with producers of concrete and bituminous pavement, with city and county planning and zoning personnel, and with representatives of various interested organizations. The conservation and ultimate utilization of deposits of construction raw materials near expanding urban areas can best be accomplished by long-range land-use projection and the requesite cooperation of technically advised planning and zoning administrators, government officials, mineral producers, and land developers.

Jan 1, 1967