Search Documents

By Scott Turner

The present rapid growth of coal stripping in the United States is a curious reversal of the tendency of mining to proceed from outcrop to depth. A combination of technical and economic factors bas stimulated the use of stripping methods until today many million tons of coal We being recovered by open cuts from sites that an earlier generation of engineers would have passed by as not commercially mineable or, if workable at all, only by underground methods. The total quantity of bituminous coal and lignite mined in the United States by stripping in 1928, the latest year for which detailed figures are available, was 19,789,000 short tons. Of this, 71,000 tons came from small workings not equipped with power shovels and 587,000 tons from properties in which stripping and underground work were carried on at the same mine; but as neither of these types is representative of modern stripping practice, they will be omitted in the discussion that follows. The total from strip pits proper in 1928 was 19,131,000 tons, produced by 176 pits employing 385 steam or electric shovels.3 Figures by States are given in Table 1. Detailed statistics will be found in Economics of Strip Coal Mining; a study by O. E. Kiessling, to be published by the United States Bureau of Mines.

Jan 1, 1930

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By Alton B. Cook, G. B. Shea

"INTRODUCTION In February 1945, Captain (now Commodore) W. G. Greeman, U. S. N., Director, Naval Petroleum and Oil 3hale Reserves, requested the Bureau of Mines to assist the Navy in its wartime development of Naval Petroleum Reserve No. 1, Elk Hills field, Calif., to assure adequate supplies of petroleum products in the Pacific theatre. Unit Operation 4/,engineers desired pressure volume-temperature and viscosity data on the reservoir oil in the shallow oil zone to augment data previously obtained for the purpose of calculating reservoir performance and oil reserves. Accordingly, arrangements were approved by the Operating Committee far, the Bureau of Mines to proceed with a program of field sampling and laboratory determinations designed to obtain the desired information.To carry out the assignment, the Bureau transferred the necessary person¬nel, subsurface pressure, temperature, and sampling instruments, and laboratory equipment for analyzing subsurface oil samples from the Petroleum Experiment Station, Bartlesville, Okla., and the San Francisco, Calif., office and set up a temporary field headquarters in the Elk Hills. The program of work as out-lined by Unit Operation required the 6 months period March-August 1945 to complete during which time individual reports comprising data on pressure-volume-temperature relationships and reservoir oil viscosities as determined on subsurface oil samples and recombined oil and gas samples for 5 selected wells were submitted to Unit Operation.This report is a summary compilation of the data contained in the original reports supplemented by correlations of some of the physical properties of the reservoir oil with the A.P.I. gravities of the produced oil. The report also includes material-balance calculations relative to one of the oil horizons in the shallow zone. The Bureau of Mines believes that publication of the results of these analyses is a worthwhile contribution to the petroleum literature and of particular interest to the California industry."

Apr 1, 1947

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

By David E. Kaslow

In sampling dust laden air by drawing the medium into an inlet, some larger particles fail to follow the air and a true sample is not obtained. Inertia prevents particles from accelerating with the air as well as from turning sharp bends; also the particles' weight causes them to fall relative to the air. An analytic solution to the sampling efficiency calculation by Levin gives particle paths and sampling efficiencies for various particle sizes when the inlet can be treated as a point sink. However, the flow field in the neighborhood of an aspirating tube is quite different from a point sink flow. Employing Levin's solution in the outer field, trajectories in actual flow fields have been calculated by computer to locate the critical trajectories separating the entering particles I paths from those paths where the particles hit the tube wall or escape. Sampling efficiencies are presented in terms of 3 variables--a dimensionless particle size coefficient, a dimensionless orifice size coefficient and the tube orientation--for the no-wind case. Over most of the range of sampling conditions, the Stokes drag law can be used and dependence on the variable--particle Reynolds number--can be ignored. A procedure for achieving maximum efficiency in design of a sampler is proposed. Whether these results apply when typical room-sized eddies constitute the ?calm air? environment is not known.

Jan 1, 1974

By Donald Christofferson

This report documents the program conducted to demonstrate the application of a flywheel-powered propulsion system to underground mining shuttle cars. Such application can replace the present electrical trailing cable common to most shuttle cars and thereby eliminate those safety hazards, maintenance problems, and haulage route limitations inherent in the trailing cable. Described are the activities undertaken to specify and design a flywheel of optimum size, shape, and material; to identify the best concepts of input and output systems; and to achieve installation of the power package into a shuttle car. The resultant Flywheel-Powered Shuttle Car is an FMC Model 6L shuttle car, 6-ton capacity, 20-ton gross vehicle weight, powered by a flywheel system with 4.5-kilowatt-hour usable energy. The completed vehicle was delivered to the Bureau of Mines in Bruceton, Pennsylvania, for testing and evaluation.

Jan 1, 1986

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

By A. Stawsky

Effective use of diesel vehicles in underground mining requires attention to improved control of diesel exhaust pollutants such as particulate (soot), oxides of nitrogen and sulfur and carbon monoxide. An experimental survey Is made of diesel emission aftertreatment control techniques including water scrubbers, catalytic converters, exhaust gas recirculation (EGR) and soot filters. Use of two or more techniques in combinations are tested for optimum control of all exhaust pollutants. Dynamometer data is developed for steady state and computer controlled simulated mines duty cycles operation of Deutz F6L-714 and F8L-413 engines. Exhaust Quality indices (EQIs) are calculated from dynamometer data for comparisons among the control combinations examined. The Corning diesel particulate filter (DPF) is shown to be the most promising and practical device. The Corning DPF in combination with EGR provided the best (lowest) EQI from the test data. Use of the DPF requires additional regeneration mechanisms such as a catalytic filter coating or fuel additives. A metal mine field test is made of DPFs on an operational scoop tram to test practical applicability. Further development is proposed for application to various mine conditions and for improvement of DPF regeneration techniques including coating with newly available catalysts.

Jan 1, 1987

By J. R. Thoenen, Hugh D. Pallister

"INTRODUCTION The Stone Hill Copper project resulted from the recommendations made in the war minerals report on this deposit by engineers of the Bureau of Mines 4/ and a similar report of the Geological Survey. 5/ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they make the greatest possible contribution to the national security and economy. The Mining Division, Lowell E. Moon, chief, conducts preliminary examinations, does the actual investi¬gative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.This report was prepared under the supervision of Paul M. Tyler, former regional engineer, Eastern Region, and is based on the examination and investigation of the deposit by Hugh D. Pallister, mining engineer, made under the immediate supervision of Richard W. Smith, former District Engineer for Alabama and Mississippi.The report was rewritten and prepared for publication by J. R. Thoenen, chief, Tuscaloosa Branch, Mining Division.LOCATION AND ACCESSIBILITYThe Store Hill copper mine is about• 12 miles south of Heflin, the oounty seat of Cleburne County, Ala. Heflin, a town with a population of approximately 1,700, is the nearest shipping point for freight and express. It is on the Southern Railway, between Birmingham and Atlanta. A rural mail route passes within quarter of a mile of the mine. Paved reads from Heflin lead to Atlanta, Birmingham, and Montgomery. The country Toads leading from Heflin are well-maintained but are practically inaccessible during inclement weather. The road crossing the property within a hundred yards of the mine needs grading and repairing (see fig. 1)."

Apr 1, 1948

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the state's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By Frank E. Williams

This Bureau of Mines report describes 147 known fluorspar deposits in New Mexico and briefly mentions 54 miscellaneous occurrences for which little or no information was obtained. Most miscellaneous occurrences are minor and too poorly exposed to be considered more than prospects. History and production of fluorspar in New Mexico, type of deposition, mineralogy, uses, and grade specifications are discussed. Total mine production of fluorspar in New Mexico is nearly 641,000 tons of various grades of crude ore and hand-sorted material. Fluorspar deposits occur in 13 of the State's 32 counties. Grant, Valencia, and Luna Counties account for 86.4 percent of the total production. During the investigation, 141 deposits were visited. A total of 72 character samples was collected for assay, and 3 larger samples were collected for bench-scale metallurgical tests. Results of these metallurgical tests indicate that an acid-grade product can be obtained with 95 percent recovery of the CaF2 content of the crude ore.

Jan 1, 1966

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By A. J. Farstad

Recent advances in microcomputer technology have opened the way for systems which can track the location of underground mining personnel from the surface. A computerized system has been designed which is capable of not only tracking the location of the miner but also of monitoring underground parameters, communicating between work stations and sounding alarms when underground conditions are judged to be unsafe. For the system described herein, the locations of the underground personnel are detected by a network of underground terminals which routinely emit RF pulses to interrogate miniature transponders worn by the miners. Each transponder is uniquely programmed to delay its response in such a way that the RF terminal can identify the individual transponders by the time slots in which the responding pulses are received. The underground terminals are then interrogated by the host computer on the surface which keeps a running account on underground mine conditions and personnel. The underground portion of the system is designed to operate even during mine emergencies, deriving its power from rechargeable battery supplies which are float charged during normal operation. Nine mines were visited on this program and the industry reaction to the system was generally favorable. By slanting the system design for daily use in the mine, the chance of its acceptance by the industry is enhanced. Furthermore its likelihood of being operational in the event of an emergency is significantly increased.

Jan 1, 1981

By J. C. Engel

Recent innovations in mine safety include the use of mercury vapor lamps for mine vehicle illumination. Such lamps, however, extinguish whenever the line voltage at the machine momentarily sags or is interrupted. The lamps must then cool for several minutes before they will restart. By supplying reduced high frequency power to the lamps from an auxiliary source, it is possible to maintain ionization in the arc tubes preventing the lamps from extinguishing. Essentially an auxiliary high frequency supply, the keep alive system provides additional power to the lamps automatically whenever the lamps are in danger of dropping out. The system can also provide the operator with the ability to dim the lamps at will for periods of up to three minutes by simply interrupting the 60 Hz power to the conventional ballasts. Each unit, housed in a steel explosion proof enclosure with a volume of approximately 0.6 ft3, is capable of servicing up to six 175 watt H-39 mercury lamps and two 100 watt H-75 reflector flood lamps. A total of 16 units were produced for the USBM under this contract and its extension.

Jan 1, 1979

By L. A. Eros

The U.S. Bureau of Mines and Western Fuels Utah, Inc. entered into an agreement to plan, install, and evaluate a micro-computer based monitoring and control system at Deserado Mine, an underground coal mine. The U.S. Bureau of Hines contracted the Colorado School of Mines (CSN) to independently evaluate the project. CSM evaluated and documented costs, benefits, problems, and management and labor perceptions in this report. Recommendations are provided for mine operators and monitoring system vendors considering future installations.

Jan 1, 1986

By R. H. Schutz

This publication lists the respiratory protective devices approved by the Bureau of Mines as of December 31, 1968, and the names and addresses of their manufacturers. The purpose of this publication is to inform the public about approved equipment for safe use in mines and mineral and allied industries.

Jan 1, 1969

By Paul M. Tyler

The outstanding trend in the graphite market is the fast-growing demand for cheaper qualities of graphite and the declining consumption of the more expensive varieties. The manufacture of graphite, crucibles for melting metals was one of the earliest applications of the-mineral and for many years constituted by far the leading source of demand. In later, years, however; and more especially since the Great War, the increasing demand for high-grade steel ingots and castings instead of enlarging crucible sales has permanently curtailed the domestic demand for crucibles because it has hastened the introduction of electric, oil or gas fired furnaces to replace the older types requiring pots to hold the metal during melting. While there has been a substantial increase in the use of graphite for miscellaneous refractories the total consumption for such purposes is too small to offset the shrinkage in demand for crucible making, and though it consumes the better and hence more expensive grades of crystalline flake graphite, it does not call so insistently for the still costlier Ceylon grades.

Jan 1, 1929