Search Documents

By H. H. Heady

This Bureau of Mines report provides specific information regarding the analysis of ores, concentrates, and bullion. It describes analytical services provided by some Federal agencies, and discusses analytical techniques applicable to the precious metals. The appendixes list Bureau of Mines State Liaison Offices and commercial assay laboratories.

Jan 1, 1976

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By Edmond Chin

The land mass of the Asia and Pacific region comprises 11 million square miles or about 15% of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest island or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The countries in the Asia and Pacific region represent some of the most vibrant economies in the world. Japan is undisputed as one of the world's leaders in manufacturing and commerce. Hong Kong and Singapore are significant both as entrepôt and banking centers. The economies of Australia, the Republic of Korea, and Taiwan compare favorably to the level of the industrialized countries in western Europe. Indonesia, Malaysia, the Philippines, and Thailand have maintained strong economic growth during the past two decades. All these countries in the Asia and Pacific region collectively constitute a significant bloc as to raw materials production and consumption, as to manufacturing, and as to world trade.

Jan 1, 1992

By W. E. Tournay

In accordance with a cooperative agreement between the Bureau of Mines, United States Department of the Interior, and the Linde Air Products Co., an investigation was made at the Bureau Explosives Testing Station, Bruceton, Pa., to develop suitable test methods for evaluating the performance and sensitivity characteristics of liquid-oxygen explosives. This report presents the results of the investigation. The unique nature of liquid-oxygen explosives necessitated both modification of standard techniques and development of entirely new test methods. The latter requirement was due to the fact that differences exist in the kind of information that must be developed for studying relative safety and performance properties of these explosives compared to that of fixed explosives.

Jan 1, 1949

By P. C. McWilliams

Theoreticians in soil mechanics have been pursuing a probabilistic approach to the factor of safety of an embankment or darn for the past 10 years. The motivation for this work is in contrast to the current practice of deterministically computing a factor of safety and treating it as an absolute with no regard to its inherent statistical variability. Basic to the probabilistic approach is the selection of an appropriate statistical model to represent the histogram or probability density function (PDF) of the factor of safety values, Rather than simply assuming which PDF is appropriate, the Bureau of Mines collected data at two waste disposal embankments for consideration, This report addresses three candidate models, using the techniques of nonlinear curve fitting, and identifies the "best" model. A propagation of error formula for estimating the variability of Fellenius? factor of safety is also discussed.

Jan 1, 1983

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By Jr. Gabler

The U.S. Bureau of Mines (USBM) has developed a computerized commodity flow model for strategic and critical materials This flow model is generic and applicable to most commodities and amenable to updating supply, demand, and/or production data change. The original model, with slight modifications, was used to track the flow of chromium. This report follows the flow of chromium through its metallurgical, chemical, and refractory applications, and highlights areas where significant losses occur because of downgrading, export, or disposal. The study indicates that materials containing 451,769 mt of chromium were consumed, including 99,221 mt of chromium from recycling, Chromium losses from all causes in 1989 were estimated to be 345,347 mt from a variety of areas. These areas and their chromium losses are as follows: processing losses, 38,825 mt; processing-downgraded scrap, 18,227 mt; manufacturing losses, 18,128 mt; manufacturing-downgraded scrap, 56,595 mt; prompt scrap exported, 1,531 mt; obsolete scrap exported, 43,443 mt; recovery losses, 155,529 mt; and recycling losses, 13,069 mt. Recycled chromium-containing material accounted for 22 pct of the apparent consumption of chromium in 1989.

Jan 1, 1994

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986

By C. Froger

Since its creation in 1950, the Centre d'Etudes et Recherches des Charbonnages de France at Verneuil-en-Halatte (Oise) has been conducting many investigations concerned with airborne dust measurements, particularly in underground mines. The work has resulted in the development, a few years ago, of a new process of dust sampling, whereby the airborne dust particles are collected by a rotary filter of polyurethane foam rotating at high speed within 8 housing.

Jan 1, 1973

The value of U.S. mineral raw material output reached a record $63.1 billion in 1975. This high exceeded the 1974 value of $55.2 billion by 14 percent. Among the three major mineral categories -fuels, metals, and nonmetals -only fuels showed an increase in value. Both the metal and nonmetal categories showed declines in value. The significance of this nearly $63 billion mineral output can be noted in the fact that it is the basis for the subsequent production of over $270 billion a year in energy and processed materials. Of the 78 individual mineral commodities included in these 1975 totals, only 17 registered gains in output, while 45 registered value increases, reflecting higher prices.

Jan 1, 1976

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have seen made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidants in mines, the Bureau of brines began systematic measurements of the movement of roof strata to in coal mines in the fall of 1935. It was decided- that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end w cooperative tine agreement was made with the Pittsburgh Coal Co., through Dr. L. E. Young, vice: president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as appear to be justified.]

Jan 1, 1937