Search Documents

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper develops a new Blastability Index to assess hole-to-hole fragmentation in bench blasting based on a new Rock Factor exclusively obtained from drill-monitoring data, that can provide an automatic assessment of rock structure, strength, and waste/ore, the effective energy factor of the explosive and the delay time per blasthole.

Feb 1, 2020

1974 The Society of Explosives Engineers officially formed to “advance the art and science of explosives engineering” on August 20, 1974 in Pittsburgh, Pennsylvania.

Jan 1, 2010

By C. E. Johnson, R. L. Bauer, E. M. Johnson

In industry, the strength of a blasting cap is often equated to the type of explosive it can detonate. Comparable cap strength is becoming less important as nearly all caps manufactured today can initiate high explosives, such as primasheet, with ease. Previous studies were conducted to assess the quantity of energy released by various detonators into the directional propulsion of the detonator’s casing. However, the question of how much of this propulsion energy is needed to initiate an explosive remains unanswered. This study will assess the fragmentation size and velocity needed to initiate a high explosive when they are not in direct contact. For this study, primasheet was used as the main charge as it is relatively insensitive and can be situated in different positions relative to the detonator. Electric, non-electric and electronic detonators were used to evaluate initiation potential. The primasheet is observed in response to being in contact with a detonator, and not in contact with the detonator at various distances and angles. This allowed the quantity of energy transferred into the primasheet to be observed and for the initiation of the sheet to be recorded using high-speed video. This study will report the energy necessary to initiate the primasheet at various distances and angles from the charge from a number of widely used, commercial, hot wire blasting caps.

Feb 6, 2023

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Paulo Couceiro, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper describes a new methodology to assess rock mass-quality to guide blasting in open pit operations. A developed Structural Block Model and Strength-Grade factor have been combined in a Rock Factor, that, exclusively obtained from drilling data, can provide an automatic assessment of rock structure, strength, and waste/ore identification.

Feb 1, 2020

By William Nicoll

Those who use electric detonators in firing blasts will be interested in a new electrical testing instrument known as the ‘Blasters’ Friend’, recently devised by the New York Blasting Supply Co. of New York. Owing to the necessarily delicate construction of the platinum wire bridge in the shell of a detonator, it frequently happens that it becomes broken or disconnected; thus destroying the circuit and rendering the detonator worthless. In many cases, misfires and premature explosions are caused by defective detonators. Heretofore, to detect the deficiencies of a detonator before using has been an impossibility, owing to the absence of a testing instrument adapted to the purpose.

Jan 1, 2010

By Diogo Fonseca, José Manuel, Nuno Fernandes, Blessing Taiwo

This research focuses on enhancing the synergy between blasting and primary crushing operations in quarries. A blast operation at dstgroup aggregate quarry in northern Portugal was simulated to fine-tune blasting techniques aimed at optimizing fragmentation indicators. The methodology involves conducting precise blast drill hole surveys, generating detailed terrain 3D models, and integrating these models into blast simulation software to enhance accuracy and optimize production efficiency. The study applies these simulations to test blasts, evaluating improvements in cost-effectiveness, crusher power consumption, and fragmentation efficiency using both aerial and terrestrial image analysis technology. The quarry key performance indicators (KPIs) guide the blast design simulations, ensuring practicality and relevance. The case study blast revealed that implementing optimum blasting techniques can enhance crusher throughput, reduce operational costs, and improve safety. This paper is part one of a three-part technical series where we aim to create a sampling procedure and establish a reliable baseline for the current state of operation. This baseline will be used in subsequent follow-up technical papers to make recommendations and improvements. The outcome of this study provides a framework for quarry operations seeking to enhance their efficiency.

Jan 21, 2025

By Robert Hopler

Blasting powder is a slow-acting, black, granular explosive made of sulphur, charcoal and either potassium nitrate (saltpetre) or sodium nitrate. The blasting powder containing potassium nitrate is known as “A” blasting powder; that containing sodium nitrate, as “B” blasting powder. “A” blasting powder is a little denser, a little stronger and a little less hygroscopic than “B” blasting powder.

Jan 1, 2014

By Manuel Gutkrrez, Nasslo Gallardo, Arturo Cancec

The study done in Dofia In&s de Collahuasi aims to improve the fragmentation in one of the most difficult rocks to deal with in an operation, It is the Ignimbrita. In order to avoid ejections and to increase the efficiency of the explosive it has been obtained an improvement in the stemming quality by using the Blasting Optimisation Program in Ignimbrita. Different materials were used in the stemming. In 1997 it was used soil material (Paleorrelleno), then in 1999 started the use of crushed gravel and during this year it is being implemented the utilisation of Stemtite only loaded with drill cutting. The first improvement was obtained with the utilisation of gravel, yielding good fragmentation results in comparison with the stemming with detritus material. The stemtite has made easier the blasting operation and it has signiticantly improved the fragmentation.

Jan 1, 2001

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Jeffrey Meissner, Mike Waldron, Charles Dowding

Most studies of crack response have focused on opening and closing of a crack in the plane of the wall in which the crack occurs. Crack movement also occurs perpendicular or normal to the plane of the wall. This paper will examine and compare the in-plane and out-of-plane (normal) response of cracks in two different residences near limestone quarries. In two locations, sensors that measure in-plane and normal displacement were installed side-by-side on the same crack, allowing direct comparison of the two modes of response. In a third location, a perpendicular pair of displacement sensors was installed in a corner of a room to observe the bidirectional response of the structure at a corner. Both long-term and dynamic data were recorded with the same sensors; temperature, humidity, and air over pressures were also recorded to compare blast and weather effects. Measurements show that ratios of out of plane to in plane response to dynamic events can vary. However, the ratios of out of plane (normal) response to vibratory events to that of climatological change is still as small as the ratio for in plane crack responses.

Jan 1, 2010

By Jerome H. Stofleth

In June of 1998, the DeBruce Grain Elevator was devastated by an accidental explosion caused by the unintentional ignition of grain dust. The DeBruce grain elevator was the largest ‘single head-house’ grain elevator in the nation. It was comprised of 450 cylindrical grain silos, 30 feet in diameter by 120 feet tall, with a centrally located headhouse. Immediately after the explosion, rescue operations were started for seven missing workers. The Federal Emergency Management Agency (FEMA) had taken over operations of the site by day two. On day three FEMA contacted the Washington DC office of the Department of Energy for explosive expertise, who in turn contacted explosives experts at Sandia National Laboratories (SNL) and Los Alamos National Laboratories (LANL). FEMA was looking for guidance in making the decision to downgrade their operation from a rescue to a recovery operation. Based on some chemical equilibrium calculations, and basic explosive engineering techniques, the SNL/LANL team was able to provide the necessary input to allow the decision to be made for the operational downgrade. At this point, only one worker remained un-recovered.

Jan 1, 2004

By Clarence Hall, Charles E. Monroe

Squibs, Fuse, and Detonators It has been made clear in the discussion of combustion and explosion and the description of various explosives that they can be caused to explode by various means. All of them can, under some circumstances, be made to explode by fire. Some of them can be caused to undergo a detonating explosion by setting off a detonator in contact with them. In blasting use is made of both these means for setting off explosives, the means used being determined by circumstances.

Jan 1, 2010

By James T. Ludwiczak

Drilling and blasting in a Karst (sinkholes and mud seams) environment has long been a problem for blasters, miners, quarry operators, contractors, and developers. While one cannot change the geological conditions, one can take some measures during the bidding process and the initial preparation of the blasting program to help reduce some of the problems. During the geotechnical investigation and developing the test/core drilling grid, the owner/developer needs to take some additional measures that will provide important data to the blaster to help reduce the problems associated with blasting this type of geology. The owner/developer must also understand that, due to the geologic conditions, the results of the blasting will not be ideal and there may be additional blast-related costs. If provided the proper geologic data, the blaster can develop drilling patterns and blast designs that will help reduce some of the more problematic areas.

Jan 1, 2005

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Ahmet Varol, Ertugrul Kaya, Turgay Ozat

This paper presents analysis of environmental effects induced by cautious blasting during the construction of the Istanbul Subway 4 Levent - Ayazaga Darulsafaka Metro Tunnel Project carried out by the contractor, located at Northern Istanbul in Turkey. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S6-7-8 shafts of this tunnel route, ground vibration components were measured carefully by using five vibration monitors during the construction of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighboring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 107 records belong to 51 shots were analyzed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for these tunnel excavations and suggested for the test sites in order to estimate particle velocity of the ground vibrations. As a result of the studies, some practical charts are created in order to minimize the psychological effects of the shots, and simplify the authorities of shots’ job. And last but not least, make sure that the shots will be done in a controlled way.

Jan 1, 2011

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997