Search Documents

By Michael Wieland

The thermodynamics work-principle was used to develop the rupture-fracture-throw (RFT) model for ranking the performance of reduced-density explosives when shot in rock or other stratum. The RFT model revises techniques used for the rock-water-jelly (RWJ) model, where the reaction-zone remains trapped within the rock/stratum. Therein, ranking of performance refers to trends for the two resolved components of the total expansion work: the reversible mechanical work taken as the heave and the residual irreversible portion, taken as the undissipated shock. For numeric tractability, the RFT and RWJ thermodynamic efficiency were taken equal, while the RWJ late-stage confinement was replaced with restrained venting through the rock, to render the RFT inefficient heave. The transfer of heat from the reaction-zone was neglected and the root-power formula was used to render the gas-covolume. Ranking trends were found for a generic charge formulation over a wide ranging density, with underwater results noted for comparison. Realistic compositions, some with natural resource materials, were treated for just typical and reduced density. Rock characteristics, ranging from hard rock to weak stratum, were represented by their density and rupture compression strength. Quantitative test results for shock or heave in rock remain difficult, so qualitative guidelines remain helpful when reviewing the graphic trends. Theoretical refinements for rock fragment size-distribution remain under development, though some relationships are touched upon to gain insight.

Jan 1, 2011

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

Blastserve, ISEE’s Listserve is being replaced by our new Blasters Forum-online, an exclusive member benefit. Our goal is to provide an ISEE forum for you to network with your peers and exchange technical information and get answers to your technical questions. This forum is unique in the fact that only ISEE members are permitted to review or post on the site. Over time you will be able review the discussion history and use the archived discussion as a valuable resource for trends in the industry. The following are a sample of the discussions that too place recently on Blastserve

Jan 1, 2013

By Mathias Jern, Ruilin Yang

A blast vibration model has been developed that simulates effects of almost all blast design parameters on the blast vibration peak particle velocity (PPV) from a production blast with multiple blastholes at a given point of interest in the rock. The velocity of detonation (VoD), initiation points, explosive types (density, VoD, energy), charge decoupling, and decking in each blasthole are simulated along with other blast design parameters. The information from signature hole blast vibration and the blast design are the input to the model. The model can be used to assess blast damage in proximity of blastholes as well as far field vibration PPV.

Jan 1, 2019

By Tacio Ferreira

A surface copper mine in the Western United States faced challenges in recovering rock and ore from final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall conditions. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The mine engineering team and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. In this paper we present how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Jan 21, 2025

By Braden Lusk

This paper includes results from analysis of recorded Acoustic Responses of Structures to Blasting. The analysis was performed to determine specific characteristics of sounds experienced inside homes during blast events. Data was collected in a typical house within the Boone North No.2 Coal Surface Mine in Ashford, WV which was instrumented for several blast vibration and acoustic responses. The instrumentation consists of four acoustic microphones distributed throughout the internal areas of the house and three geophones buried near the house. Two additional channels collect the trigger signal and Air Blast information. For each blast event recorded by the system, the mine blast reports were used to obtain major blast characteristics such as distance from the blast to the instrumented house, weight of explosive used, number of boreholes, delays, and other important parameters. This information allowed study the relationship between the acoustic response and the blast design. From a database of 43 records, five records were chosen for complete analysis. These records were chosen based on distance from the blast to the house, and specific blast parameters. This paper presents the result of the relationship between the frequencies and amplitudes for the entire trace of acoustic records, the response due to ground vibration (GV), and the response due to air-blast (AB). Frequency content was obtained through Fast Fourier Transforms (FFT), using D-Plot software. The records have a typical shape that permits cutting and analyzing each part of the signal with respect to GV and AB separately. Some conclusions are reported concerning the relationship between blast parameters and acoustic response of structures.

Jan 1, 2009

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Thomas H. Kleine, Alan R. Cameron, William W. Forsyth

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995

By Andrea Brickey, Ethan Marcoux

The South Dakota School of Mines and Technology (SD Mines), located in Rapid City, South Dakota, is one of only a few universities in the United States that offer a Bachelor of Science in Mining Engineering. The Department of Mining Engineering and Management (MEM) at SD Mines teaches courses that introduce students to concepts related to mining, including a course covering explosives engineering. Students are taught the basics of explosives theory and application in the mining and construction industry through a series of lectures and assignments. With limited field experience, many students find some topics difficult; these include: flyrock, ground vibration, timing, and others. Some US mining schools have an experimental mine in which they can simulate field conditions and conduct hands-on training, but not all universities have such facilities. For those without, teaching certain concepts can be more challenging in a pure classroom environment. To counteract the lack of an experimental mine, the mining department at SD Mines implemented Paradigm (Version 18.4.4984.0; McKenzie, 2017) a computerbased blast modeling software to improve the learning environment.

Jan 1, 2019

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

By Ron J. Elliott, Corry Coumans

The following is a detailed description of the blasting procedures used in the successful demolition of the Stave River bridge, Mission, British Columbia, Canada. This highway bridge spans a highly sensitive salmon-spawning river. Demolition of the bridge took place in a high liability situation in close proximity to sensitive structures. The new highway bridge carrying an exposed 150mm diameter gas line was located only 1.5 meters away. The bridge piers were blasted only seven meters from overhead power lines. Control of blast vibration, flyrock, and underwater overpressure was critical to the success of the operation. Electrical sequential blasting was used to ensure that blast vibration on the new bridge structure was kept below 50mm per second.

Jan 1, 1998

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Kevin Dunfield

The Deltadet System is composed of: The Deltadet II electronic Detonator. A Field Terminal to create, modify or simply execute an existing blasting sequence. The radio remote controlled option is composed of a Base Station to program, calibrate and initiate the EDDs plus a Blasting Box to send commands to the Base Station. Blasting lines to connect the EDDs to the Base Station (100m) and Visual Blast software to create or modify a blasting sequence.

Jan 1, 2004

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By Yessica Idrogo, Omar Gómez, Francisco Pérez, Eduardo Yrigoyen

Rock blasting is one of the most important operations in the mining cycle value chain, requiring optimized explosives mixtures to get good results. A new and better strategy, and that which is discussed herein, is to design a new emulsion explosive, which can provide improved characteristics and benefits over and above general types of emulsion explosives. It is therefore critical that this product is functional over a wide range of conditions

Jan 1, 2019

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008