Search Documents

By Y. Y. Emelianov

The results of the test work of four treatment options of three refractory gold-pyrite and gold-arsenic flotation concentrates are presented. These concentrates were obtained during the concentration of primary ores of large gold deposits. It was found that ultrafine grinding of refractory flotation concentrates did not increase the recovery of gold during subsequent cyanidation. The elimination of sulfur and arsenic during oxidative roasting is 99 per cent. 88-93 per cent of gold is recovered by cyanidation from calcines. After biooxidation of the flotation concentrates with a mixture of strains Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans 88-91 per cent of gold is recoverable by direct cyanidation. The recovery of gold from flotation concentrates by pressure oxidation is 88-99 per cent. These results suggest that gold recovery is important but the following strategies would have an impact on a plant performance and would be considered when developing an option to treat refractory ores: capital and operating costs, ore reserves, mine location, infrastructure and qualified staff. Keywords: gold, flotation concentrates, recovery, cyanidation, roasting, biooxidation, pressure oxidation

Sep 1, 2012

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Andrey V. Yevdokimov

The results of the test work on gold leaching using high strength of cyanide solution in the presence of activators are presented. The major physical and chemical relationships of gold leaching were determined. Intensive cyanidation results of gravity concentrates with various material compositions using an activator are given. Process design criteria for intensive cyanidation unit were developed on the base of pilot plant test results. Keywords: gold, activators, intensive cyanidation, gravity concentrates

Sep 1, 2012

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By Elves Matiolo

This paper describes, in detail, results obtained from a research study of a complex iron ore aiming to produce a pellet feed concentrate with at least 65% of Fe and less than 3.5% of SiO2 in the final concentrate. The work includes an ore desliming followed by column flotation at laboratory scale. The ore sample was from Carajás province - Brazil and represents a complex low grade compact itabirite ore, analyzing 35.9% Fe, 45.1% SiO2 and 0.57% of Al2O3. Yet, the feed was treated previously by magnetic separation and grounded to 97% < 20 µm; this sample was named MAG 2. The chemical and mineralogical characterization of the MAG 2 sample showed that Fe and SiO2 grades were 50.7% and 24.3% respectively and was composed mainly by hematite, goethite and quartz. The particle size distribution, using a laser diffraction technique, showed that 90% of the particles were < 18 µm; 50% less than 8 µm and 10% minor than 1 µm. When the cationic reverse flotation without desliming was tested the selectivity of the process was very low and did not meet the concentrate metallurgical goals of the pellet feed product. However, when desliming was applied prior to flotation, a concentrate product with chemical characteristics of the pellet feed was obtained. The best results after desliming and column flotation achieved global iron metallurgical recovery of 72% with Fe grade in the concentrate of 66.5% and 2.1% SiO2 using starch as depressant for the iron oxides minerals at 1200 g/t ? 1500 g/t and an amine as the quartz collector at 100 g/t concentration (pH constant, at 10.5). It is believed that the desliming stage was key in the separation of the iron bearing particles and has a high potential for the flotation process of this type of ores.

Sep 1, 2012

By Kwan Ho Kim

In this study, free fall tests are conducted with the objective of understanding the breakage properties of waste concrete for the guide of the direction of the better comminution process. Waste concrete of 75mm×53mm is tested at various drop heights with or without heat pretreatment. Test results indicate that a block of waste concrete does not break by free fall, but eventually breaks by repeated free falls. The number of free falls required for complete separation of large aggregates from the cement mortar considerably reduced when the samples were heated at 400?. Therefore, a great energy saving can be obtained when heating the waste concrete prior to crushing. The energy saving was found to be dependent on the height of free fall but in all cases, was still large enough to offset the additional energy required for heating. Also, it was found that the heat pre-treatment gives an additional advantage in that it produced cleaner recycled aggregates. This may result from easier detachment of cement mortar from the aggregates due to weakening of bonding forces by heating. By analyzing the size distribution of the crushed product, a free-fall breakage model is developed using the particle breakage ratio and the breakage pattern. The developed model can be used to predict and to analyze waste concrete processing circuit.

Jan 1, 2014

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By X. G. Liu

Bentonite is an excellent sealant mineral material because of its desirable swelling and self-healing characteristics, low permeability, sorptive qualities, and longevity in nature. A new type of water-swelling building sealant made from bentonite was studied in this paper. The building sealant is prepared by Na-base bentonite, vaseline and paraffin wax under different mass fraction of bentonite (which is 60%,65%,70% respectively). Under unrestricted state, some properties of samples were investigated. The volume expansion ratio at 24 h is 211%, 222%, 256% , and permeability coefficient is 2.86×10-8 cm/s, 4.15×10-8 cm/s and 4.78×10-8 cm/s respectively; low temperature flexibility of the sample (bentonite quality is 65%, 70% respectively) is good, and it does not flow heated for 2 h under 80?. The results of XRD and SEM indicate that bentonite is coated preferably by vaseline, and the spacing of layers of bentonite do not changed. The sample can keep full water swelling ability, and has good molding process. The test results prove that the properties of samples may reach the standard of building sealant.

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By B. Tora

Coal mining activity is inextricably connected to waste production. These include coal slurries deposited in environment. Current knowledge in the field of mining and especially mineral processing allows extracting valuable fuel from deposit coal slurries. The article discusses of previous works devoted to coal slurries inventory in Jankowice Mine in Poland (Upper Silesia) and quality assessment of coal slurries. 12 samples of coal slurries deposited in waste pond of Jankowice Mine was taken for the investigation. Total amount of wastes deposited is more than 100 thousands tones. Keywords: re-flotation, coal wastes, waste storage, industrial verification

Sep 1, 2012

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By D. G. Hulbert

"Mineral processes are complex operations that have been modelled, controlled and simulated by diverse technologies. A review is given of some models of mineral processes in the literature. A new variation of a dynamic process model of flotation is presented. Process models, describing real and relevant physical variables, give a good understanding and good qualitative simulations, but can sometimes require prohibitively difficult and extensive parameter estimations. Process control is usually best done on operational plants by the fitting of system models, which can home in on the plant?s observability, controllability and optimisation. System models can be of a form amenable for use in appropriate techniques for controller design and implementation. The control of milling circuits is discussed in some detail. While simulators use models to predict dynamic or steady-state information, part of their strength lies in their ease of use and their ability to test different types of specifications. Some results are given for a flotation circuit simulator that can be made to solve virtually any permutation of specifications.INTRODUCTIONThe development and application of appropriate technology can lead to better operation of mineral processing plants in industry, so that substantial benefits can be obtained from improved throughputs, efficiencies and product qualities. This paper addresses some of the principles and methods used in the quest for the development and exploitation of such technology. Although the design of processes is often the motivation for modelling and simulation, this paper also targets the use of modelling and simulation for the control and optimum operation of mineral processes. The two processes given the most attention here are flotation and milling.Technologies used in mineral processing range from simple to very complex. Simple technical principles, such as mass and component balances, can yield some simple and effective strategies for modelling and control. However, minerals in particulate form have such complex physical and chemical properties that there appears no end to the complexity that emerges, as more and more factors are taken into consideration in the pursuit of better results and understanding. The situation is aggravated by the complexity of mineral processing plants, which have spatially variable conditions within process units, and complicated interactions between these units."

Jan 1, 2003

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By A. V. Abshilawa, D. G. Talakhadze, R. I. Sturua

"Processing of the tailings accumulated over the lifetime of Madneuli Copper Concentrator is an opportunity to extract additional salable copper and gold products. This paper presents a pre-concentration process for the valuable components (copper and gold) of the accumulated tailings. The developed process makes it possible to obtain a copper pyrite concentrate with a yield of 14.05%, copper grade of 1.36%, and recovery of 83.22% containing 3.78 g/ton of gold at a recovery of 84.31%. The bulk concentrate is produced by a combined process bringing together selective flotation to produce salable copper concentrate and hydrometallurgical processing of the selective flotation tailings to recover gold. KEYWORDS: FLOTATION, ALBION PROCESS, LEACHING, COPPER CONCENTRATE, SELECTION Madneuli Copper Concentrator, Georgia, was put into operation in 1975. Over its lifetime, 40 mn tons of tailings have been accumulated at the tailings storage facility (TSF). Sampling of the TSF has indicated that the average copper and gold grade is 0.23% and 0.56-0.65 g/ton, respectively. Accordingly, the TSF can be classified as a technogenic reserve. This paper discusses pre-concentration of valuable components using flotation, followed by processing of the bulk concentrate in the Albion process. Mineralogical analysis of the accumulated tailings showed that the main ore mineral is pyrite (11.71%). Copper minerals are mainly represented by chalcopyrite (0.7%). The main nonmetallic mineral is quartz (67.3%); sericite, chlorites, etc. also occur. Pyrite is present both as liberated grains and intergrowth. The absolute majority of copper minerals are found as intergrowth with pyrite, less often with quartz. Ore minerals are slightly oxidized. Chemical analysis results are shown in Table 1. Particle size distribution shows that the size class -0.2 mm - 0.045 mm has the highest grade of 0.85 to 0.97 g/ton of gold. Size class +1.25 mm has the lowest grade. Based on the chemical and mineralogical studies and particle size distribution, an optimized process was developed for pre-concentration of the valuable components prior to hydrometallurgical processing. Several gravitation, direct selective, bulk, and bulk selective flotation processes were trialed. (1,2)"

Jan 1, 2018

Anglo American Platinum practices fine grinding in its processing plants to enhance the liberation of valuable minerals. If the fine particles of valuable minerals generated during fine grinding are not recovered during the flotation process, this could significantly contribute to the overall losses. This study examines the flotability of fine moncheite (PGE mineral) particles in a controlled environment (moncheite size distribution, concentration and liberation). A barren Norite ore ground to 40% and 80% passing 53µm was spiked, with four different size fractions of moncheite (-5, -10+5, -25+10 and -53+25µm) in order to evaluate the effect of particle size on flotation. The investigation also included the effect of energy input and collector dosage on the flotation of two moncheite size fractions, namely -5µm and -10+5µm. The results showed that the moncheite particle size has a significant impact on flotation. Coarse particles (-53+25µm) showed the highest Pt flotation kinetics and overall recoveries. The -5µm size fraction of moncheite could also be recovered by flotation, however, at a lower rate compared to the other size classes investigated. The increased collector dosage of 300g/t at the finer Norite grind of 80% passing 53µm enhanced the flotation rate of the -5µm size fraction of moncheite when compared to the lower collector dosage of 150g/t. The higher energy input during laboratory flotation, at an impeller speed of 1000rpm also increased the flotation rate of the -5µm size range, however, at a lower concentrate grade, when compared to the lower impeller speed of 700rpm. More favourable Pt flotation kinetics data was obtained for the -53 +25µm size fraction of moncheite at the fine Norite grind when compared to the coarse Norite grind. Keywords: flotation, moncheite, particle size, energy input and SIBX

Sep 1, 2012

By C. Kleine

Coal sorting with an x-ray-transmission (XRT) sensor has experienced a lot of development since first described by Jekinson et.al. in 1974. Powerful computers and increasingly sensitive X-ray scintillation counters enabled the development of high-performance sensor-based sorting machines. The first industrial installation of a belt-type XRT-sorting for coal is in operation since 2004. It is upgrading high quality coal from 1% ash to 0.7% ash for cathode production. In comparison to the high quality coal which is treated with a belt-type sorter, the chute type sorter has been successfully optimized for high volume coal treatment of lower quality coals. This project was funded by the German Environmental Fund (Project Nr.244444). In cooperation with the RWTH Aachen University and Isambane Processing, CommodasUltrasort(now Tomra Sorting Solutions) conducted extensive pilot test work under production conditions in 2010 for the destoning of power station coal at Arnot Power Station in South Africa. The experience gained during this pilot test phase led to an optimized, redesigned PRO Secondary XRT Chute sorter which is now in operation at a South African coal mine. This flexible semi-mobile modular destoning plant is treating a size range of -120 mm +30 mm at a throughput of 150 tph. The implementation of this plant not only reduces the ash content, abrasiveness index and sulfur content significantly, but also reduces royalties, water treatment and transport costs.

Sep 1, 2012

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012