Search Documents

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By Yoshio Mitarai, Takeshi Nagatome, Yosuke Tanaka

"This paper describes an application of lightweight soil in a deep water area to stabilize an existing quay wall at the Port of Tokyo. Super Geo Material, abbreviated SGM, is a type of lightweight soil, which consists of dredged cohesive soil, cement and air foam, and is applied in coastal development work, such as port and airport construction. This paper reports a SGM construction project at the Port of Tokyo by using a SGM special plant vessel, which was deployed for the Tokyo International Airport (TIA) Expansion Project in order to achieve large-scale and rapid construction. The key issue in SGM construction is quality control. One key quality issue is control of the mix proportion of SGM in consideration of volumetric changes due to air foam-breaking during pumping and air foam shrinkage due to water pressure when SGM is placed in deep water. A smart technique for placing SGM is also necessary to prevent quality deterioration when SGM is placed in deep water, for example, increased bulk density and decreased shear strength due to water absorption. This paper introduces an actual case of SGM construction with a particular focus on quality control of SGM during construction.INTRODUCTIONSuper Geo Material, abbreviated SGM, is a lightweight stabilized soil which is used in coastal development work in Japan (CDIT 2008). SGM is applied as a backfilling material behind existing quaywalls or above underground structures in order to reduce earth pressure on the existing structure and improve seismic resistance. SGM has been applied in many coastal development projects. In particular, SGM was used at the Tokyo International Airport (TIA) Expansion Project (Haneda Airport) as the backfilling material at a quay wall at the joint between the reclaimed area and pier part in a new runway (Nagatome et al. 2010a & 2010b, Yamatoya et al. 2010, Mitarai et al. 2011). In this project, large-scale and rapid SGM construction was implemented by the special SGM plant vessels within 6 months under the condition of limited construction period.This paper introduces a new SGM construction project at the Port of Tokyo in 2011. This project employed the special SGM plant vessel, “Ryujin Mark II”, to achieve large-scale and rapid construction within a limited period. SGM was also placed in a deep water zone at the maximum water depth of approximately 15 m. Thus, quality control of SGM was a key issue for meeting project requirements. This paper describes the actual SGM construction in the Tokyo Bay area and quality control techniques for SGM, considering volume changes due to pumping and placement below water."

Jan 1, 2015

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By Antonio Kodsy, Lutful Khan

A research was carried out to test the possibility of reducing the pullout resistance of metal sheet piles driven in clay soils using Electrokinetic (EK) conditioning. The hypothesis was applying an electric gradient for a certain period of time should reduce the adhesion between the clay soil and the sheet piles. Tests were conducted on bench scale thin stainless-steel metal plates embedded in pure kaolinite clay, and mixtures of kaolinite clay and sand. The pullout resistances were determined after 20, 40, and 60 minutes residence times of steel plates in the soils before and after EK conditioning under an electric gradient of 1500 V/m. In kaolinite clay, the pullout resistance showed linear reduction with the duration of EK conditioning and about 60 % reduction in pullout resistance was observed after 60 minutes EK conditioning. For the kaolinite-sand mixtures, the pullout resistances were reduced by about 70% and 80% for 20% and 30% sand contents respectively after 20 minutes EK conditioning and showed no significant improvement with the increase in conditioning duration. It was concluded that the proposed electrokinetic conditioning process could potentially reduce the pullout resistance of metal plates embedded in clay and clayey soils. SHEET PILE WALLS Sheet pile walls are typically used at waterfronts as retaining structures or during the construction phase to shore the soil and avoid collapse of the excavations. When used as permanent structures, sheet pile walls are not removed after the completion of the project. However, as temporary support, they are extracted after the completion of the project and reused. In pure clay soils the extraction processes often becomes a challenge requiring very large pullout forces which could damage the sheet piles. There is a research need for developing an efficient method of sheet pile extraction from clay soils addressing the issue of pullout force reduction. However, very few researches have been conducted regarding the extraction techniques of sheet piles and their economic effect on the cost of a project. In this study a novel method for reducing the pullout resistance of sheet piles in clayey soils using electrokinetic conditioning was explored. The hypothesis of this research is that the electrokinetic process in soil/water system, specifically electrophoresis and electroosmosis, could be used to loosen the sheet pile walls embedded in cohesive soil and hence reduce the required force of extraction. The aim of this study was to test this hypothesis through laboratory tests carried out on steel plates embedded in cohesive soil samples. The pullout forces of the steel plates before and after varied duration of electrokinetic (EK) conditioning were evaluated and compared. The process was also investigated for clay-sand mixtures.

Jan 1, 2019

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Alessandro Bertero, Stefano Valagussa, Filippo Maria, Wesley Schmutzler, Leoni

"Abstract The Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. Differences and the importance of performing pre-construction laboratory and field tests will be highlighted. Comparative analyses and interpretations between the various lab and field stages, along with accumulated information about soil properties and QC results, allowed fine-tuning of the production parameters throughout almost the entire project.Two projects where the US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilizations, and a third project completed in Italy, will be illustrated:•,?the LPV 111 Project (New Orleans - LA – USA); DMM was used for groundimprovement/foundation strengthening and consequently stabilize and support the burden of the new levee.•,the Rio Puerto Nuevo Project (San Juan - PR - USA); DMM was applied to improve the soils adjacent to a 90” forced sewer main relocation and to improve the soils for the base of a new drainage channel•,the new Italian high speed railway project (Florence Italy); DMM technology was applied to realize a a TBM break in/break out, foreseen originally by jet-grouting.IntroductionThe Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2014

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2013

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By Mohab Sabry, Emre Biringen

"Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.INTRODUCTIONUnder the high applied loads coming from the superstructure, the addition of piles is primarily required to improve the factor of safety against failure when a raft does not provide adequate bearing capacity. If the bearing capacity of the raft is sufficient to carry the total load with a reasonable safety margin, then the addition of piles is usually intended to reduce the settlements to an acceptable amount. In current practice, the design process for pile-supported raft foundations conservatively concentrates on providing solely the pile capacity to carry the total structural load without taking the contribution of the raft into account. This paper addresses the potential use of hybrid piled-rafts in controlling foundation settlement of power plant structures by considering the support of both the piles and the subgrade soils beneath the raft to carry the load."

Jan 1, 2017

By John L. Walkinshaw

It is obviously not possible in the time given me today to review in great detail all the research of the past 20 years that the (FHWA) has sponsored or participated in. In this presentation I will highlight some of the principal programs that I am familiar with. This handout lists practically all the reports prepared for the FHWA involving deep foundations and some related work involving the same structural elements (piles, shafts, ground anchors).

Jan 1, 1993

By Frédéric Rocher-Lacoste

On July 2nd, 2007, LCPC and LOADTEST performed a static loading test with an Osterberg-cell on a bored pile of 1600 mm diameter. The 56.50 meters deep test pile constructed by Trevi Spa for Soares da Costa group, was near the Cacheu river in Guinea Bissau. This test was conducted to validate the design of the foundations of the Sao Vicente bridge; a project undertaken by the Ministry of Public Works of the Republic of Guinea Bissau and funded by the European Development Fund. Sub-surface conditions at the test pile location consist primarily of layers of weak sands and clays. The piles were loaded statically using the O-cell® bi-directional method 25 days after concreting. The maximum sustained bi-directional load applied to the pile was 11.7 MN. At the maximum load, the displacements above and below the O-cell assembly were 6.6 mm and 81.9 mm, respectively. The resulting pile head behavior has been calculated for a combined skin friction and end-bearing load of 29.3 MN. The piles were also instrumented using LCPC removable extensometers, which made it possible to measure the mobilization of shaft friction and toe resistance. The adjusted test data indicated that this pile would settle approximately 12.2 mm for the service load of 12MN applied at the head of the pile. This paper provides a very brief presentation of the bridge project and the test pile instrumentation: LCPC removable extensometers and O-cell® instrumentation. The results are detailed and analyzed herein and the combined use of these two instrumentation systems is a world première.

Jan 1, 2008

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By Stefano Pirrello

"Sydney’s booming real estate market has pushed property developers to invest in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement Piles (DD) techniques are on the other hand suitable for these ground conditions. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West. The advantages of DD over CFA piles such as reduced overall spoil with substantial cost savings and achievable rock sockets in medium strength bedrock are discussed. Design validation through interpretation of real-time data from the piling rigs’ on-board computer data, and low and high strain pile dynamic testing (PDA) is discussed. Testing data is presented as CAPWAP (Case Pile Wave Analysis Program) analyses for different concrete grades.INTRODUCTIONThe booming real estate market in Sydney has pushed property developers in investing in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement (DD) Pile techniques are on the other hand suitable for these ground conditions and were utilised using concrete injection methods. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West.GEOLOGY & GEOTECHNICAL CHARACTERIZATION OF THE SITEThe Sydney 1:100 000 Geological Series Sheet shows that the site is underlain by man-placed filling and alluvial/estuarine sediment. The sediment comprises silty to peaty sand, silt and clay. Shell layers are also expected to be present within the soil profile. The Prospect/Parramatta River 1:2500 Acid Sulphate Soil Risk Map shows the site as ‘Disturbed Terrain’ in which soil investigations are required to assess acid sulphate soil potential. Several Cone Penetration Tests and Boreholes were carried out during the geotechnical investigation. All boreholes were extended to bedrock and NMLC-sized diamond core drilling was used to obtain 50mm continuous core of the rock, enabling unconfined compression strength testing to be carried out on selected samples. A summary of the ground conditions encountered on this site and inferred from the CPTs can be described as follows:"

Jan 1, 1900

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015