Search Documents

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By M. Tominaga

An industrial port complex was constructed on the west coast of Leyte Island The work was started in December 1981 and completed in May 1984. This port complex includes a 665 m long wharf and can accommodate vessels ranging from a 60,000 DWT ore carrier to a 4 000 DWT general cargo ship. It now handles materials for and products from a copper smelter with an annual capacity of 130,000 t and a fertilizer plant with an annual capacity of 900,000 t. The Wharf structures consist mainly of interlocked steel pipe piles, steel sheet piles and steel pipe Piles. Material handling equipment such as unloaders, shiploaders, etc. were installed on the wharf. Site survey, planning, engineering design and construction aspects of the port development are discussed in this paper with particular emphasis on the wharf structure.

Jan 1, 2010

By D. Waite

The Chairman opened the session by wondering why so few papers on Maritime Structures had been received for this conference. Perhaps because the marine environment is so hostile and the access so difficult that engineers tend to be more prudent about new ideas and designs. Dennis Waite noted the number of grey hairs in the room - grey hairs which could be equated with experience gained the hard way. He hoped that this experience would be passed on in the discussion period of this session. The Chairman was delighted to welcome two authors from China, Mr Sun and Mr Liang. He was most grateful on behalf of the conference for their efforts both in preparing their papers and for being able to present them. He regretted that Messrs Noce and Fedolino were not able to present their paper and then welcomed Mr Christensen from Denmark who would present the first paper.

Jan 1, 1991

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By M. Makarchian

Existing buildings sometimes experience excessive settlement under their design loads, or due to increased foundation loading, if a change of building use is required. One of the oldest and widely numerical study has been carried out of a simple idealised problem of an underpinned rigid circular foundation to better understand the behaviour of pile used for underpinning and load transfer mechanism from an existing foundation to the underpinning piles. The finite element method has been used for this analysis, with the soil treated as a two-phase elasto-plastic material. It is found that the effect of the length of the pile becomes more significant as pile length increases. As would be expected, the earlier the pile is installed, the less is the final settlement.

Jan 1, 1996

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By Derrick D. Dasenbrock

Three piers of a new river bridge are supported on 1.067 m diameter open-end steel pipe piles. At time of drive, and after pile re-strikes, high-strain dynamic capacity values at plan tip elevations, were as low as 23% of design requirements. Pile lengths were extended 20% to 40% deeper than planned at two piers, driving to rock, impacting both the project cost and schedule. The significant discrepancy between predicted and observed capacity was investigated through a series of coordinated dynamic tests; a full-scale test pile was installed and monitored over 221 days by both dynamic and quasi-static methods. Unusually slow strength gains were observed by dynamic monitoring on all piles installed at the site. CPT soundings were advanced at the test pile and through the pile interior to investigate the soil plug. High-strain dynamic methods were found to have significant limitations in properly assessing the long-term capacity of large-diameter open-end pipe piles during driving and short-term pile re-strikes. As the benefits of large diameter high-capacity open-end pipe piles are numerous, the geotechnical community needs to address appropriate construction monitoring and control of these foundation types to take full advantage of these systems. An improved understanding of the physical effects of pile installation and the impact on soil strength assessment while driving and long term soil strength gain should be developed and incorporated into both design and monitoring procedures to avoid either unsafe or needlessly costly designs.

Jan 1, 2006

By Vincent Jue

In December 2009, the Italian High Speed Rail Network AV began running over the full 1000 km system length from Turin, at the foothills of the Alps to Salerno, on the seacoast south of the volcano Mt. Vesuvius. It runs through Alpine rivers, highly seismic active zones, mountains, river plains, and through some of the most densely populated areas in Europe as well as some of its most expensive real estate. The Italian High Speed Network?s technical/economic constraints and its regulatory/socio-environmental concerns well may mirror similar obstacles set to confront the nascent California High Speed Rail Program. The two types of constraints must be dealt with together to reach the best construction solution. It is estimated that more than 20% of Italian High Speed Rail Network costs were spent on ground engineering including over 150 km of tunnels, 200 km of viaducts and bridges and 650 km of embankments and trenches. However, it also is estimated that 25% of costs were spent on social and environmental integration of the new rail lines including over 6 square miles of green offsets, 160 km of anti-noise walls, and 300 agreements for socio-environmental work. This paper will look at four examples of innovative ground engineering solutions, each with its own intricate set of constraints: ? Foundation system for viaducts across the ?Po? and ?Ticino? rivers. ? Soil consolidation under railway embankments ? Requirement of short tunnels for physical and environmental reasons ? Construction of railway stations in a confined right of way

Jan 1, 2010

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006