Search Documents

By Sailesh S. Author

The current design method for soil-cement (SC) columns improved soft clayey ground under the highway embankments assumes a slip circle failure surface shearing through the columns and the soils using a weighted average shear strength. However, the results from the laboratory centrifuge model test and numerical analysis indicate that in many cases, the SC columns fail by bending. Some researchers have proposed methods for estimating the maximum embankment loading for bending failure of SC columns, but those methods have limitations in correctly considering the internal shear stresses or not applicable for the group SC column improvement. Numerous model embankments on SC columns have been simulated by three-dimensional (3D) finite element analysis (FEA) and the mechanism of bending failure and the magnitude of the bending moment in the SC columns under embankment load has been investigated. Based on the simulated results, the design method for the estimation of the bending failure of floating SC columns has been proposed. The predicted results from the proposed method agreed with the existing field condition of one embankment in Saga, Japan reported in the literature in terms of the stability of columns. Hence the proposed method can be used for the design of floating SC columns in the soft ground.

By Ramanathan Ayothiraman, Anurag Singh

"An experimental program was undertaken to investigate the effects of randomly distributed basalt fibre on the index and engineering properties of Dhanori clay and to compare its performance with the properties of soil reinforced with polypropylene fibre. In the present investigation, 7 groups of soil samples were prepared at four different percentages of basalt fibre and polypropylene fibre content and tests were done for measuring their consistency limits, compaction characteristics, unconfined compression strength and consolidation properties. The test results indicate that the inclusion of basalt fibre in Dhanori clay resulted in significant improvement in properties. The improved properties are not comparable with polypropylene fibres, nevertheless, the improvement by basalt fibres is able to meet the typical design target values and the cost is very much less than synthetic fibres. More importantly, basalt fibres are environment friendly.INTRODUCTIONConstruction of buildings in low lands with engineered filling, flexible and rigid pavements for highways/airfields, and embankments for highways/railways are also part of major infrastructural development in addition to construction of tall buildings, bridges/fly overs, major dams and underground structures. The later projects require different improvement techniques than that is adopted in the former projects. Ground improvement techniques such as use of reinforcement inclusions within soil found as an effective and reliable technique. Especially such modification by fibre reinforcement, is primarily possible in engineered filling, pavements subgrade and embankments, where surface mixing is easier; and may not be feasible when stabilization/modification is required for deeper depths. In comparison with conventional reinforcement using geosynthetics (strips, geotextile, geogrid, etc.), there are some advantages in using randomly distributed fibre as reinforcement. In past few decades, the discrete fibres are simply added and mixed randomly with soil, in much the same way as cement, lime, or other additives.There are several studies (Ziegler et al. 1998; Puppala et al. 2000; Bei-xing et al. 2004; Cai et al. 2006; Tang et al. 2007, 2012, 2016; Abdi et al. 2008; Viswanadham et al. 2009; Le et al. 2015) that investigated the behaviour of polypropylene fibre-reinforced soil and reported that an increase in fibre content caused an increase in strength and shrinkage potential but brought on the reduction of swelling potential. The length of fibres had an insignificant effect on soil characteristics, whereas fibre contents proved more influential and effective. A study on rubber fibre conducted by Hambirao and Rakaraddi (2014) mentions that tensile cracking of clays can be improved with the inclusion of short rubber fibres, optimum fibre content was about 15 % of weight of soil. Several experimental studies (Babu et al. 2008; Chaple and Dhatrak 2013; Vibhakar and Nahta 2014; Soundara and Senthilkumar 2015; Goyal et al. 2015; Jayasree et al. 2014, 2015) were conducted on coir fibre-reinforced soil and concluded that it helped in reducing the swell potential and 1% fibre by weight of the soil almost doubled the CBR value. Martins et al. (2015) found that 4% of sisal fibre by weight of the soil reduced the visibility of cracks. Pillai and Ayothiraman (2012), Ayothiraman et al. (2014) and Sahu et al. (2016) have demonstrated that human hair fibres can be used to improve the properties of both fine grained and coarse grained soils."

Jan 1, 1900

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete walls. PRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete wallsPRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Jim Cook

Arsenal Football Club required the development of a new home stadium in north London, subsequently named the Emirates Stadium. The proposed development comprised a 60,000 seat stadium, with associated facilities and a sports training centre. Described are the foundation solutions and piling construction techniques used, which take into consideration the potential impacts on existing above and below ground railway infrastructure and underground water structures. Methods used by the piling contractor to improve aspects associated with health, safety and quality are also described.

Jan 1, 2008

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By Douglas L. Scaggs

Driving piles in under water applications has become more common place over the past twenty years. Where only a water depth reachable with a follower or dewatered cofferdam was the rule in the past, newer technologies developed for the offshore oil and gas industry have made depths of even several thousand feet possible offering new possibilities in foundation design and installation. With the new technology, engineers can now more efficiently design structures by placing foundations optimally thereby reducing weight and cost of the overall structure.

Jan 1, 2013

By Achyut Kumar Allady, Praveen Arumughan

NCHRP Synthesis 418 (2011) entitled, “Developing Production Pile Driving Criteria from Test Pile Data” details the occurrence of dichotomy between pile Skin resistance and pile Tip resistance mobilizations at different times for different hammer blows during pile driving operations. With increasing usage of High Strain Dynamic Testing (HSDT) the engineering community started paying more attention to this occurrence of dichotomy resulting in overdriving, pile damage, increased claims, and loss of time. To overcome the dichotomy limitations of HSDT, NCHRP recommends, “the use of superposition to combine the back-calculated tip resistance from a blow on initial drive or from redrive with the back-calculated skin resistance from the early blows at the beginning of restrike”. However, the current practice of external mounted gauges and signal matching for a single blow are unable to evaluate independently the Skin resistance and Tip resistance to achieve the goal of determining the optimum Total Pile Capacity using the superposition. This paper discusses advancements of science and technology with sensors embedded at the pile top and pile tip, the data collected is analyzed by the state-of-the-art FDOT Method to determine Skin and Tip resistances independently for every blow. Independent Tip and Skin resistances each with a Resistance Factor can be summed up to obtain optimum Total Pile Capacity. Additional benefits of determining independent Skin and Tip resistances include obtaining lost skin capacity due to scour, due to pre-drilling/preforming and uplift tension capacity. Furthermore, the benefits of embedded sensors include increased quality control/quality assurance through 100% testing, accelerated construction, life cycle monitoring and asset management.

May 1, 2022

By Todd Nottingham

Channel deepening of major ports is challenging designers to explore innovative solutions to ensure stability of bulkheads, such as for the Oakland Inner Harbor. This particular challenge was met with the use of the SPIN FIN® Tension Pile for restraint of an HZ combination wall along the Oakland Inner Harbor Shoreline in Oakland, California. A SPIN FIN pile is a pipe pile with welded plates at the pile tip that increase pile capacity. A brief history of the project will be provided as well as results of pile load tension tests, pile strain gauge, and wall deflection under construction loads. Tension pile load deflection results will be discussed with recommendations toward establishing deflection-based ultimate load criteria. A discussion of predicted wall loads and field observed wall loads will be provided.

Jan 1, 2008

By Spencer Ness, Yazen Khasawneh, William Tjaden, Mohammad Nassim

The evaluation of long-term performance of the wind turbine structures is essential in lowering the Levelized Cost of Electricity (LCOE) from wind sources. The required maintenance of the wind turbine foundation during the design-life time of the wind turbine may result in escalated cost, if not properly evaluated during the planning and designing phases. The degradation of the foundation soils’ stiffness due to the accumulation small plastic strains resulting from normal and/or extreme operating cyclic loading may result in escalating the O&M cost. The foundation’s stiffness degradation will result in a shift of the wind turbine system natural frequency, which may result in amplifying the vibrations generated at the hub. The anticipated shift of the wind turbine system natural frequency during the design-life time should be investigated through numerical simulations of the anticipated dynamic loading utilizing soil constitutive models that are capable of capturing the foundation stiffness degradation due to the accumulation of such small plastic strains. This study presents the validation of an element model that will be used to evaluate the performance of existing and/or proposed constitutive model.

Oct 1, 2022

By Julie H. N. Hampden, Per G. Reinhall

"Executive summary: Impact pile driving of steel piles is a common construction practice in freshwater and marine environments for the building of structures and foundations. This practice produces extremely high sound levels underwater that have proven injurious to aquatic fish and wildlife. To limit impacts to sensitive species, resource management agencies employ a variety of different strategies including timing restrictions to limit in-water construction windows to those months when there are low flow conditions in lakes or rivers, to those hours when tides are low, or to periods of the year when species of concern are least likely to be present in the project vicinity. In addition, permitting agencies have identified noise thresholds above which sensitive species could be injured, resulting in additional project conditions to curtail the extent of project noise impacts including: limiting the number of piles or pile strikes per day, requiring biological monitoring, and mandating the use of noise attenuation techniques, such as bubble curtains and cofferdams. Numerous studies have shown current noise attenuation techniques are costly and provide limited or variable noise reduction [1-3]. This is because the noise from pile driving is not only transmitted through the water column, it is also transmitted through the sediment back into the water column [1, 4-8]. Though these protective measures may help to reduce project impacts, they also result in additional complexity, expense, and potential risk for project delivery. Marine Construction Technologies, a Public Benefit Corporation, in collaboration with University of Washington and Washington State Department of Transportation, has developed a pile that can be installed with standard pile driving technologies (vibratory or impact hammers) and consistently decreases the total noise transmitted into the water. The double-walled pile is relatively quiet in comparison to unattenuated piles or existing noise attenuation techniques. This technology not only reduces the risk to sensitive species by minimizing the extent of potential impacts, it also reduces potential risks to project delivery by limiting the size of monitoring areas, minimizing the need to cap daily production rates, and eliminating the need for deployment of additional noise attenuation devices. Results from finite element modeling of the pile, scaled prototype testing, and full scale field testing in Commencement Bay (October 2014) and Vashon Island (October 2015) in Puget Sound, Washington indicate a reduction the peak sound pressure between 14 and 20 dB relative to single walled piles at a range of approximately 10 meters. These tests also confirm that the double-walled piles provide drivability similar to standard steel piles. In addition, preliminary calculations for capacity and structural characteristics demonstrate that double-walled piles provide equivalent or better performance than same-sized standard piles."

Jan 1, 2017

By Sebastian Fischer, Rolf Katzenbach, Steffen Leppla

"The risk management in the case of liquefaction is one of the most serious and also difficult issues in geotechnical engineering because failure caused by liquefaction is always a sudden failure without ahead indication. For that reason ground improvement technologies for the prevention of liquefaction are necessary. The paper explains the responsible and effective risk management. Methods for the risk management and stabilizing the soil sustainably are described in detail.1. INTRODUCTIONDue to population growing more and more settlement area is needed, which is often including improper regions (e.g. mountain and coast regions) with raised risk of various kinds of disasters. But also in densely populated areas the risk of disasters like landslides can occur. One reason for the raising of risk in densely populated regions can be the opencast mining for raw material production. An essential element of the opencast mining is the loose deposition of the removed overburden, the so-called “overburden dump”. When an opencast mining is running out of the raw material, an opencast hollow remains in landscape. The slope areas of these hollows mostly consist of loose bedded material of the overburden dump. Due to the end of groundwater conservation these loose bedded slope areas are flooded. In consequence the slopes are in extreme danger of becoming liquefied. The result of a liquefaction in these slopes will unavoidably be a slope slide. Such a slope slide can extend up to several hundred meters into the landscape and can move several million cubic meters of material. An upsetting example for such a landslide is the slope failure in the German city of Nachterstedt on July, 18th 2009, which made necessitate remedial measures and also prevention works for the further utilisation of the region. The phenomena of liquefaction is not limited of slopes in series of opencast mining. Especially in regions with a highly appearance of earthquakes the phenomena of liquefaction is well known.2. RISK MANAGEMENTAn essential part for the stability assessment of slope systems is the investigation of sensitivity against liquefaction. In the case of given sensitivity against liquefaction there is no calculation method according to soil mechanics to determine the factor of safety against slope failure. Just for the case that sensitivity against liquefaction is not met, a comparison of the load (effect) E and the resistance R which is the traditional verification of stability against slope failure, can be calculated (Figure 1)."

Jan 1, 2015

By David Miller

"The biggest concern about using soil mixing is the inability to observe physically the final product, which has led to a lack of confidence about what is in the ground. After all, you can’t see it and you can’t taste it and you can’t smell it, so are you sure it’s soil mixing? In addition, there are variations in techniques, tools and monitoring that have led to additional skepticism and the desire to “elevate” the product. This skepticism is why the industry is so scrutinized even when there are other technologies being used that do not experience nearly the same level of scrutiny. With other techniques, even with a slurry wall, you can see the backfill before it goes into the ground, and drilled piers have careful evaluation of the concrete mix even before placement into and verification of the open hole. Essentially, you get control over the final material. There is less control in soil mixing, and it’s very dependent on in-situ conditions. These factors make it difficult to rely solely upon installation parameters, quality control (QC) and verification tests. At some point, you may need to apply some engineering judgment.Start at the BeginningThe availability of sufficient and accurate geotechnical data (soil type, heterogeneity, shear strength parameters, variability, etc.) is important in establishing the material that will be drilled. This data will also help in determining the proper mix design to achieve the desired soil cement properties. Many factors must be considered when designing the mix and the mixing program, including any debris in the ground, different soil properties and varying moisture contents.Each of the various factors affect the final properties of the soil cement, so it really takes careful planning and evaluation of the mix design through iterations by looking at the soil types and adjusting the mixes. Clay is going to behave very differently than sand in both mixing efficiency and final properties. That is, the presence of clays results in more difficulty in achieving higher strengths and to physically mix the soil and the binder, whereas the presence of sands results in more difficulty controlling the final permeability."

Jan 1, 2017

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By Jason N. Scott

It is now possible using low-cost wireless technology and rugged hand-held devices to record data on site electronically and for that data to be instantly available to others. This could potentially eliminate many problems that traditionally lead to remedial work, such as poor communication and the late detection of non­conformances. However, determining how best to implement such a system and integrate it with the rest of the business process is far from simple. This paper looks at Stent's experience of these issues by way of a case study of the SHERPA system. This is a wireless site data collection system developed for use with rotary bored piling.

Jan 1, 2006

By Jamey Rosen, Georgette Hlepas

"Bluestone Dam is a concrete gravity structure with an overall length of 2,060 feet and a maximum height of 165 feet above the streambed. Several major project modification designs have been implemented and additional modifications are currently in construction and design phases. Due to the various modifications since original construction was completed in 1948, detailed documentation with visualization of the project features is needed. A three-dimensional model of the internal and external features of Bluestone Dam was generated from LiDAR data, survey information, and other data sources. One of the key features of interest in this model is an accurate visualization of over 200 dam anchors based on downhole anchor surveys. The model is accessible in Microstation and Geographic Information Systems (GIS), allowing users to rotate the anchors in three dimensions; view them in the context of geology, internal dam structural features, historical construction records, site photographs, bathymetric data, and instrumentation data. Users can “click” on individual anchors to view associated construction details and open a comprehensive installation packages. The model will be used by the United States Army Corps of Engineers (USACE) as part of a larger Geospatial Data Management System as a historical accounting of the project construction data, and be a long-term living document for use by both design engineers and operations staff to assess dam safety risk and to design future project modifications.IntroductionDuring the life of any project, critical data concerning the construction and performance history are required to be collected and maintained. The data collected prior, during, and post-project construction help with the design process, ensure that the project is built to specifications and is performing as per design intent. During the Post-Implementation Evaluation (an evaluation performed after a major project modification), these data are used to visualize the repairs, verify the construction was performed per design intent, and document the history of the construction phases, associated test results, and overall effect on the project. The project described in this paper is the construction of a system of tools to effectively use these data.Data collected and maintained during the operations phase helps to ensure that the project is continuing to perform as per design and aids in advance warning of any potential failure or required maintenance. Dam Safety, Emergency Management (EM), and Operations and Maintenance personnel can use the system to verify the status of the project in preparation for a high flood event. For example, if there is repair work being performed on a critical feature of the project that would affect the operation of the dam structure during a flood event, Operations personnel would be responsible to update the status of the system such that Dam Safety and EM would be able to identify the feature that is out of service, its date of expected repair completion, and the implications during a flood. In addition, risk assessments typically require a full history of the project and its performance. Any concerns that arise concerning the safety or performance of a project will require a full documented history of the project and its components. Proper documentation and data management are key in this assessment process."

Jan 1, 2016

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015