Search Documents

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

By S. B. Ballantyne, D. R. Boyle

"Detailed studies have been conducted on the dispersion of uranium in stream waters and sediments around various types of mineralization and hitherto unexplained anomalous areas in the Okanagan Valley and Highland region of south-central British Columbia. These studies were part of the jointly funded and planned Federal-Provincial Uranium Reconnaissance Program of the Geological Survey of Canada and the British Columbia Ministry of Energy, Mines and Petroleum Resources. Statistical analysis of regional data indicates that U in stream waters and sediments varies considerably for different rock types, thus affecting data interpretation. In addition, the data demonstrate a poor correlation between U in stream waters and their associated sediments which can be largely accounted for by variations in climate and water and sediment composition. Regional trends in the distribution of U can be explained in terms of the above secondary factors as well as primary metallization phenomena.Significant correlations between U and F, and U and Mo can be explained by certain magmatic and mineral-forming processes. U shows little correlation with other base metals.The dispersion characteristics of U in the vicinity of Miocene "" basal type "" mineralization ; uraniferous pegmatite terranes, anomalous lineaments in granitic terranes and high-background volcano-sedimentary areas are discussed. Highly anomalous U concentrations in waters and sediments may not always be indicative of mineralization, and guidelines for interpretation require a sound knowledge of the geological and secondary processes operative in the area."

Jan 1, 1980

By F. C. Robles Hernandez

This paper presents the results of the electromagnetic semi-solid treatment of the 319 aluminum foundry alloy, Various levels of structure modification were achieved controlling the AC current used to create the Electromagnetic Field, thus manipulating the intensity of the field, The level of grain refinement, partial modification of the Al-Si eutectic, as well as cellular dendrites were observed, A quantitative analysis of the structure was performed using Image Analysis (IA) techniques. In addition a novel Thermal Analysis methodology was developed for the on-line determination of the microstructure modification level.

Jan 1, 2004

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By Tom Shumka

INTRODUCTION ?The Electro-Magnetic Crack Detection (EMCD) technique is an electromagnetic inspection method used for detecting and sizing surface breaking flaws. ?It works well on structural material or welds, ferrous or non-ferrous metals. ?EMCD?s rapid scanning is achieved using a hand-held probe. ?EMCD provides reliable crack detection and sizing (length and depth). Cracks can be sized accurately. ?EMCD dramatically reduces most cleaning requirements as there is no need to clean to bare metal. ?EMCD is capable of inspection through thin metallic coatings, or through non-conducting coatings up to 10mm thick. ?EMCD allows full data storage for back-up, off-line view and audit purposes.

Oct 1, 2010

By Chuanhui Cao, Shimei Liu, Xiaojing Li, Yueyuan Zhou

"Force analysis on weakly-magnetic particles and non-magnetic particles in magnetic field are presented, using a kind of permanent magnetic drum magnetic separator, which is designed with strong specific magnetic force and open magnetic system. Its surface peak intensity reaches to 1.0T, and the distribution density of capture line is 1.25×103/dm2. Qualitative analysis on the particles including its magnetic property, particle size, motion speed, magnetic field intensity, etc. is also presented to calculate the separating parameters for the drum separator. Experiment was conducted for the separation of fine weakly magnetic minerals for example ilmenite. The practicability to separate the minerals using separator designed with open magnetic system has been proved, providing an economic way for efficient separation of micro-fine weakly magnetic minerals and upgrading of non-metallic minerals. INTRODUCTIONMagnetic separation is a mineral processing method based on the differences of magnetic properties between minerals in inhomogeneous magnetic field (Sun, 2007). Currently for separation of micro-disseminated weakly magnetic iron ore, electromagnetic high intensity magnetic separators with closed structure of magnet system are often used. And for the separation of strongly magnetic minerals such as magnetite, low intensity drum magnetic separators with open magnet system are often used. In order to lower the operation costs and improve energy efficiency, it is important to develop efficient high intensity permanent magnetic separator with open magnet system, to some extent replacing high intensity electromagnetic separator.Oberteuffer (1974) discussed the magnetic force and competing forces in magnetic separators which compete with the magnetic forces and act on all of the particles which travel through the separator are those of gravity, hydrodynamic drag, fraction, and inertia in magnetic separation."

Jan 1, 2016

By H. Y. Sun, Q. Y. Tan, X. P. Niu, L. Li, Y. Jia, R. M. Ruan

During bioleaching processes of sulfide minerals, the sulfide minerals act as the natural habitats for acidophiles, of which, most are autotrophic iron and sulfur oxidizing microbes. These microbes acquire energy by oxidation of sulfide minerals, and play crucial role in bioleaching processes. In the industrial bioleaching heaps, microbial community and their activity are highly related to engineering configurations, while the optimized industrial operation can help to fast dissolution of aim minerals and acid/iron balance under optimized microbial condition. Microbial community succession and activity formation, the function of microbes to mineral dissolution, the mechanisms to promotion and inhibition of sulfide minerals oxidation, and the industrial instances for microbial community regulation were reviewed. For these instances, promoted microbial activity helped to fast pyrite oxidation for sulfuric acid generation, which realized zero sulfur acid addition to the irrigation solution in the initiation of a bioleaching heaps. High microbial activity by optimized operation parameters improved Cu leaching efficiency during the heap bioleaching process. And also by inhibition of microbial activity, especially the iron oxidizing microbes, the excessive pyrite oxidation can be inhibited, which helped to the acid/iron balance during heap bioleaching. INTRODUCTION Around the world, high grade copper ore are exploited, while barely new high-grade deposits are succeeded, the copper grade of ore deposit is constantly decreasing. The increasing copper demands worldwide requests to process these low-grade ore deposits. Processing of low-grade ores are not economical by usual extraction processes. Heap leaching is a cheaper process for recovery of low-grade ores, and has been applied to extract valuable metals from sulfide minerals worldwide, such as copper, gold, uranium and nickel (Gericke et al., 2009). Heap leaching process has greatly decreased the economic grade and expanded the recoverable ore reserve worldwide (Brierley, 2008). It is usually carried out in the open environments, and could process huge amount of ore (usually in millions of tonnes in one reactor) in the heap reactor (Gericke et al., 2009). For copper sulfide, especially the secondary copper sulfides, heap (dump) bioleaching is successfully applied. Heap bioleaching process is cost saving, and sometimes can be achieved without adding chemical into heaps, by microbial fixing of the atmospheric N2 and CO2, and generating oxidant Fe3+ and sulfuric acid in heaps from oxidation of sulfide minerals. Also heap bioleaching is environment friendly by cycling use of the leaching solution, and without exhaust emission.

Jan 1, 2019

By Harold S. King

TWO summers ago I had the privilege of visiting No. 18 colliery at Glace Bay. Underground, we travelled along the haulage-way behind a powerful electric locomotive. The motor in this locomotive began to smoke badly and a carbon tetrachloride type of extinguisher was used several times during the trip. At the time, I noted a strong odour of phosgene. On my return to Sydney, I spoke to Mr. Harold Gordon, Assistant to the General Manager of the Dominion Steel and Coal Corporation, and warned him of the danger of using this type of fire extinguisher in confined spaces, since it is a well known chemical fact that phosgene, a dangerously toxic gas, is formed by the decomposition of carbon tetrachloride. This danger does not seem to be widely recognized, so it seems advisable that a more general warning be published. Attention was first drawn to the danger by the death of two men in the United States Navy Department subsequent to breathing fumes from carbon tetrachloride used in a fire, and when an employee of the Bureau of Mines also was overcome while fighting a fire with carbon tetrachloride liquid. These accidents led to an investigation of the decomposition products of carbon tetrachloride by a group of workers in the Research Laboratory of the Pittsburgh Experimental Station, U.S. Bureau of Mines, the results of which were published in the October, 1920, number of the Journal of the .Franklin Institute (1). Their experiments were conducted by two methods. The first consisted in applying the liquids to actual fires and -to hot metal in a closed room of 1,000 feet capacity, where the gaseous products, mixed with air, could be retained and analyzed. The second method was to pass the vapour:s in air through heated tubes of iron or quartz, where the humidity of the air and the temperature could be controlled.

Jan 1, 1939

By L. A. Melis, J. W. Rowson

"Cluff Mining has successfully operated a gold recovery plant at its Cluff Lake operation in northern Saskatchewan to recover gold f rom Phase 1 uranium leach tailings. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-inpulp, gold recov ery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and operating data and metallurgical results from the operation are provided.INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 per cent by Cameco and 80 per cent by Amok Ltd. /Ltée. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake, 700 km north of Saskatoon, capable of processing 300 000 tonnes o f ore to produce about 4 000 000 lb UPs (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""0"" uranium orebody from 1980 to 1983. The leach tailings from the Phase I mill operation were found to contain elevated level s of gold . These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the""0"" orebody .During the Phase I operation some 6475 tonnes of leach tails were produced and stored in a total o f 2916 large concrete containers (vaults). This method of storage was, at the time, deemed to be the preferred method of temporary storage for the tailings.This temporary storage of high-grade gold tailings facilitated the reclamation and reprocessing of the leach tail s for gold recovery. The primary reason for reprocessing the Phase 1 leach tails was to provide for long-term permanent disposal of the material as an admixture with Phase II tailings in the Cluff Lake tailings disposal area. Although there was limited tonnage, the high gold content in the material made the in stallation of a gold recovery circuit economically justifiable."

Jan 1, 1989

By Y. Nara, N. Aramaki, M. Maruyama

Evaluation of three dimensionally non-uniform strain distribution in rocks under various conditions such as in water or under freeze-thaw cycles is of significant importance to understand their complex deformations and fracturing mechanisms. For this purpose, we developed an image analysis method which can evaluate or “measure” the three dimensional (3-D) strain distribution in rocks. The proposed method utilizes the 3-D images of rock under initial and deformed configurations, which are obtained by some imaging techniques such as X-ray computed tomography (X-rayCT). In the proposed method, the obtained 3-D images are divided into multiple sub-regions of interest. For each sub-region, the strain is evaluated utilizing 3-D affine transform with unknown coefficients to be determined. In the first step, 3-D voxel level displacements at multiple representative points in each sub-region are computed by 3- D digital volume correlation technique between the comparison images and the initial-guess of the transform coefficients are obtained. In the second step, referring to the initial-guess of unknown transform coefficient, they were optimized in sub-voxel level by finding optimum digital volume correlation between the comparison images, which can evaluate the transform coefficients with higher precision. From the calculated transform coefficients, the strain was directly obtained through the spatial derivative of displacement based on affine transform. In this paper, along with the description of the proposed method, the evaluation of deformation in a lignite specimen due to immersion in water was presented as an application example. As the 3-D imaging technique, micro-focus X-rayCT was applied. The result showed that the induced dilatational strain field due to the initiation and extension of cracks in the specimen was clearly captured. Therefore, authors believe that the proposed method can be applicable to various problems in rock mechanics.

Jan 1, 2015

By A. R. Laplante

"In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and as such they perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is ineffective in recovering very fine ( <15 µm) or flaky gold, as encountered in flotation feeds, concentrates or tails. It is the: preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 µm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm3 ), especially from coarser gangue. INTRODUCTIONThe purpose of this presentation is to describe the mode of operation of two Canadian centrifugal concentrators, the Knelson and Falcon. It is hoped that it will prove informative to prospective users in the selection, testing and optimization for applications of either machine. The work is based on testwork both in Canadian mills and at McGill. I am indebted to many colleagues at these locations. Appropriate references will be made to articles further describing the work, either already in the open literature or in preparation.Although this work is meant to be more practical than scholarly, it is appropriate to begin by considering how the two units achieve selective recovery. This will become useful in establishing a suitable testing methodology, which will then be described, and interpreting typical results. In the last section I will attempt to define appropriate applications for the two units. This is a thankless task, as I am likely to miss some applications or to make projections based on partial results, as much of the work is still in progress. In deference to the reader and both manufacturers, areas where reasonable doubt still remains will be identified."

Jan 1, 1993

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors&apos; thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda&apos;s diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors&apos; thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda&apos;s diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By S. E. Malouf, W. Thorpe

"The Chibougamau Explorers property comprises 35 claims or 1,726 acres in La Dauversiere and Rohault Townships along the west shore of Norhart Lake. The property is serviced by a twelve-mile all-weather high-way leaving the main St. Felicien-Chibougamau highway at mileage 121. This road junction will be a railway siding on the C.N.R. St. Felicien-Chibougamau branch line in early 1957. The property lies 30 miles due south from the town of Chibougamau. The mine-sponsored Chibougamau Explorers town has a population of 250 with 28 residences and a well equipped recreation centre.The original showing was found by Rider Storn, a prospector financed by Val d'Or interests during the 1950 field season. This showing did not stand up to detailed prospecting but it did lead to the discovery of the main zone by A. Oakley during the following winter.The company was incorporated in I 950 under the presidency of E. Ayrhart. Financing following the initial drilling involved an increase of capitalization from 3 to 5 million shares and the advent of financing and management control by Anacon Lead Mines Limited.Exploration and development to Jan. I, 1956, has included 42,331 feet of surface diamond drilling; 31,363 feet of underground drilling; a 3-compartment shaft to 1,245 feet, with 8 levels at 150-foot intervals; and I 1,054 feet of drifts, crosscuts, and raises. Ore reserves to the 900-foot level, proven and partly developed, total 546,725 tons averaging 0·30 ounces gold and 0·93 per cent copper. A mill with capacity of 500 to 750 tons will be installed by January 1956.GeologyThe Chibougamau Explorers property lies along the belt of Keewatin volcanics striking through Bachelor Lake, Opawica Lake, Doda Lake, Coapatina, Norhart Lake, and Rohault Lake, where it is in close proximity to the paragneisses of the Grenville series. The boundary of the paragneisses, a gradational contact, lies within a mile of the Chibougamau Explorers shaft collar."

Jan 1, 1949

By Morris Wong

"An antimony-bearing gold ore was studied in a cyanide slurry containing 7 -20 ppm dissolved oxygen. 1 g/L NaCN at pH 9.5 and 48 hours retention time is required to extract 94 % of the gold from the 90 % minus 200 mesh ore by conventional cyanidation at a 7 ppm O2. As oxygen concentration was increased to 20 ppm, the conditions required to extract the same amount of gold were: 0.25 g/L NaCN, 16 hours retention time and 80% minus 200 mesh. Compared to conventional cyanidation, oxygen-enriched leaching was shown to reduce retention time by three times and cyanide consumption by four times. The kinetics of gold dissolution related to the dissolved oxygen concentration in slurry was expressed by following equation:XAu = 100 * (Kt + I0) / (1 + Kt + I0)where XAu is the percentage gold extraction; t is the retention time; K and Io are the slope and the intercept of the plot of XAu I (100 -XAu) vs. t respectively. The values of Kand Io depend upon the concentrations of cyanide and oxygen, the fineness of grind and the origin of ore sample etc.. A preliminary cost analysis was also performed to justify the use of oxygenating slurries.IntroductionGeneral:It was proposed almost 149 years ago (Elsner 1846) that oxygen is required for the dissolution of gold in cyanide solution. However, little attention were paid to oxygen application in the gold milling industry during the following one hundred years. Due to the constraints of gold price, reagent costs, refractory ores, and environmental issues in the past decade, the oxygen enhancement in the cyanidation process was introduced to the gold milling industry for increasing operation efficiency, reducing production costs, and meeting the requirement of environmental standard.The advantages of oxygen-enriched cyanidation have been reviewed by several investigators (Hague 1992, Jara et al 1992, Henderson 1989, Loroesch et al 1988, Elmore 1987, Cathro 1963). Common to all conclusions are the following advantages."

Jan 1, 1995

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By I. A. Cameron

In 1979, John Peacey and William (Bill) Davenport published The Iron Blast Furnace Theory and Practice billed as "An up to date and comprehensive treatment of blast furnaces from fundamental principles to modern operations" (back cover). As a 1979 graduate of McGill University’s Metallurgical Engineering program, I belonged to the last "beta" student group which completed the prescribed blast furnace course work before The Iron Blast Furnace Theory and Practice was published. As my career developed, I become an international blast furnace consultant and have worked with blast furnace operators and raw material suppliers on 5 continents. The blast furnace is the dominate iron making process responsible for 70% of global steel production. Blast furnace engineers have implemented many improvements by manipulating the blast furnace process metallurgy using the principles presented by Peacey and Davenport to reduce coke consumption and increase oxygen usage and blast furnace productivity. This paper briefly summarizes some key principles presented by Peacey and Davenport (1979), describes process improvements made by blast furnace operators over the 35 years since The Iron Blast Furnace Theory and Practice was published and outlines important future developments in blast furnace technology.

Jan 1, 2014