Search Documents

By E. J. Wade

The general location, climatic conditions and access of the Tasu mine are covered briefly, with comments on the Jack of conventional transportation and communication facilities. The Haïda story of Tasu and early at-tempts at production are presented, together with a discussion of the government legislation which throttled exploration and production in the late fifties. General and specific details of local geology, mineralogy and current ore reserves are also covered.

Jan 1, 1968

By O. G. Olvera, E. Asselin, D. Rival

Particle concentration distributions in a leaching tank have been estimated using a novel experimental approach that takes advantage of the galvanic interactions that occur between pyrite (FeS2) particles and a Pt electrode. The collision of FeS2 particles with Pt changes the open circuit potential measured with the electrode due to galvanic interactions. To discern particle collisions with the Pt electrode from experimental noise a simple analytical procedure was first adopted although the use of techniques involving frequency domain analysis is also briefly presented and discussed. Although this method is still under development, it is simple to implement and can yield valuable information regarding the hydrodynamic behavior of solid particles in stirred tanks in very short times. Finally, the advantages and drawbacks of the technique are discussed.

Jan 1, 2014

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By A. C. Hawken, L. M. Strah

"The Report outlines the Conversion to Rubber Mill Liners and steel grinding balls from the old style Cobalt pocket liners and flint pebbles which had been used in 5'x22' Fraser-Chalmers tube mills for over fifty years. An outline of the past history and some of the plant modifications are mentioned as well.The details pertaining to considerations, modifications and repairs carried out on the mills are described. Factors influencing the rubber liner design are outlined along with the description of the rubber liner design.The performance and advantages to date are given and concludes with brief summary.HISTORYThe original amalgamation-cyanidation mill of Dome Mines Limited went into operation in 1912. Milling has been continuous since 1912, except for two periods; one of 17 months commencing in December 1917, and the other of about 12 months, when fire destroyed the plant in November 1929. Initially the capacity of the mill was 350 tons a day. In 1916 it was raised to 750 tons a day, following which there was a gradual expansion to 1,500 tons a day."

Jan 1, 1977

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

Open pit production planning is a procedure consisting of multiple stages. Although all the planning stages rely on the geostatistical block models, long- to short-term plans each require their appropriate resolutions and levels of details. The main motives behind using different resolutions are the tractability of the models and the practicality of the generated schedules. The current approach in the mining industry is to use nested pits generated by Lerchs-Grossman as the basis for long-term planning and to use manually generated polygons, within those pushbacks, as the units of production control in mid- and short-term planning. However, the nested pits generated by Lerchs-Grossman algorithm and the polygons drawn by mining engineer do not provide control over the value and tonnage of ore and waste inside the planning units and therefore cannot lead to optimum solutions. In this paper, we first present a pushback determination approach which maximizes the profit of the mine with control over the tonnage of ore and waste within each pushback. We then propose a clustering approach with size and shape control that determines aggregates within those pushbacks; and finally, we introduce a mathematical programming model which uses the generated pushbacks and aggregates as the planning basis and generates production schedules that maximize the net present value of the operation and are practical from the operation?s point of view.

Aug 1, 2013

By X. Wu

Tunnel Boring Machines (TBMs) are widely used for tunneling in urban areas because of their high advance rate, precise as-built profile and minimal impact to buildings and traffic on the ground. For a tunnel built by a TBM, there are strict requirements on alignment control and safety. To meet these requirements, it is important to monitor the position of the TBM. In the current practice, the TBM position data, including advance distance and line and level deviations, are reported manually to the managers on a daily basis. To interpret and analyze the position data, the managers also need to refer to various construction drawings. This practice is untimely, inefficient, and error prone for decision making. To improve the current practice, an automatic approach for real-time as-built tunnel product modeling and visualization is proposed, based on TBM position and orientation data autonomously sourced from the Virtual Laser Target Board (VLTB) TBM Guidance System developed at University of Alberta. Related information of the tunnel project, such as the as-designed alignment, soil layers, the ground, existing utility lines, is also visualized together with the model of the as-built tunnel. The modeling algorithm is presented step by step. Its application in a real-life drainage tunnel project is discussed and limitations are also identified.

Aug 1, 2013

This paper presents the results of research aimed at proposing new solutions in the area of belt conveyor elements. Many factors, such as energy consumption costs, and operating costs of belt conveyor elements, including belts, idlers and drives have an impact on the operational costs of conveyors. The paper presents special tests of new materials for the bottom cover of an energy-saving belt conveyor, which decrease rolling resistance. It also presents large-scale in-situ tests of a high-output belt conveyor for the purpose of simultaneous measurements of various types of conveyor belts (standard vs several energysaving types) under typical operating conditions of a lignite surface mine. Improvements in materials used for the bottom belt covers, supported by specially developed comprehensive tests of the new types of belts have provided valuable results of various proposed solutions. Since the tests of belts were done at exactly the same time and in the same operating conditions, direct comparison of the results is valid and should lead to a substantial decrease in the conveyors? drives? energy consumption, which will improve the effectiveness of belt transport and minimize its negative influence on the environment.

Aug 1, 2013

Operating CIP/CIL gold recovery plants in the arid regions of Western Australia face unique challenges due to water and ore quality issues. The presence of cations of Mg, Fe and Cu metals in water supplies and leached sulphide ores can have considerable effect on plant consumption of lime and cyanide, due to pH buffering and complexation effects. Reagent costs are critical to many of these operations. In this paper, computational modelling is used to analyse a number of process options to mitigate such issues. This requires careful consideration of the chemistry of the process system, and the ability to predict accurately the response of speciation and precipitation reactions to changing process conditions. The Mg-Fe-Cu-CN-H20 system is specifically modelled in this application. The Gibbs Free Energy Minimisation thermodynamic framework has been selected to model equilibrium phenomena. Furthermore, this approach has been extended to the process flowsheet level, incorporating multiple unit operations and recycle streams in a steady-state mass balance model. The Gibbs equilibrium composition module of HSC Chemistry software has been successfully integrated into the commercial flowsheeting package SysCAD. Consideration of the Gibbs Energy Minimisation capabilities of other flowsheeting packages has also been given. This approach has been successful in simulating the aqueous process chemistry typical of such plants. It has resulted in a predictive capability where equilibrium states respond appropriately to process changes. Potential cost savings may be identified by examining alternative process conditions to minimise overall reagent consumption.This methodology may be extended to other hydrometallurgical plants where issues of solution ideality, temperature and other equilibrium processes are sufficiently understood.

Jan 1, 2005

By C. E. St. Denis

"Training Program at Sherritt Gordon's Ruttar:. ConcentratorA formal training program for mill operators is being developed and employed at Sherritt Gordon's Ruttan Concentrator. The program was set up to fulfil the needs created by a shortage of skilled reliable labour, a 200% turnover of personnel within the first six months of operation and the rapid advances in mineral processing technology. All new employees are introduced into the Mill Department through an orientation program designed to familiarize them with the operation of the plant. All training and orientation of new employees is the responsibility of a. small training section consisting of two training foremen and one assistant. Using a combination of classroom and supervised on the job training, the training times have been cut by at least one half. High operating standards have been set and are maintained through the use of detailed manuals for each work area and competent instruction at all operating levels. The major portion of training costs arise from the salaries of the training staff but are negligible when compared to the improved recoveries, smaller turnover and less downtime. Government assistance is available to all industrial employers to offset the costs of training employees."

Jan 1, 1974

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By Richard W. Herzer

Introduction Thermal methods have been predominant in the metallurgy of the base-metals ever since the foundation of the industry thousands of years ago. Development in hydrometallurgy has been confined largely to the past six or seven decades. It was at first necessarily slow, then for a number of years rapid progress was made. At present, the uncertain state of the metal industry has curtailed research on the subject; however, in the next few years one may assuredly look forward to an ever increasing use of wet processes. Leaching methods have attained the dominant position in the case of certain metals, notably zinc. For others, they have made no headway at all. Copper presents a situation all its own. Due to the varied nature of its ores and to the large number of localities in which it is mined, a great number of processes have been developed, each suitable in its own particular field. In the case of this metal, therefore, it is more difficult to arrive at definite conclusions. It is the purpose of this paper, first, to review the outstanding developments of base-metal hydrometallurgy, and, secondly, to consider possible Canadian applications of some of the processes in use. The discussion will be confined to the three metals, zinc, lead, and copper, with particular reference to the last mentioned. Zinc General Note At present, zinc is produced by two principal processes, the older retort process and the electrolytic process. The latter is a development of the last twenty years and, judging by its present progress, bids fair eventually to supplant older methods in a large proportion of cases. It is certain, at least, that in the erection of a new plant, a hydrometallurgical process would be given the most serious consideration

Jan 1, 1934

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By John R. Hayes, Kebbi A. Hughes, John Rowson, Peter E. R. Blanchard, Jeremiah C. Beam, Andrew P. Grosvenor, Arthur Situm

Uranium ore bodies contain elements within mineral phases that need to be disposed of responsibly. Solid waste can be placed in a tailings management facility (TMF) to contain the waste elements and limit interactions with the environment. It is important to understand how the chemistry of the tailings evolves throughout the lifetime of the operations that feed the TMF and after the site has been decommissioned. The objective of our collaboration with Orano Canada was to study how the tailings from the TMF located at McClean Lake, Saskatchewan change over time. This manuscript discusses our use of X-ray absorption spectroscopy (XAS) and X-ray microprobe to study the fate of Mo and Ca in the tailings. Mo is considered an element of concern (EOC) and it is necessary to determine if a stable solid Mo-bearing species forms. Thermodynamic modeling suggested that aqueous Mo would precipitate over time as powellite (CaMoO4). Comparing Mo K-edge XAS spectra from the solid tailings to the aqueous Mo concentration in the pore water showed that powellite did form and that this did result in a decrease in the aqueous Mo concentration over time. Further, it has been proposed that Ca2+(aq) can react with bicarbonate ions in the pore water and precipitate as calcium carbonate (e.g., CaCO3). This reaction would limit the aqueous bicarbonate present in the tailings that could react with uranyl ions to form soluble uranyl-carbonate complexes. We have identified several trace Ca-bearing species, including carbonates, in the tailings using XAS and X-ray microprobe.

Jan 1, 2020

By Roger K. M. Bellows

The last coal-fired power plant to be built in Canada came into operation in 1994. Since then, Canada?s electricity requirements have grown substantially but no new coal-burning plants have been built. This country has abundant resources of coal from coast to coast, but in recent years, this has not affected our choice of fuel. In many other countries this is not the case, and the use of coal is growing rapidly. Although this presentation covers the topic from an Alberta perspective, some of the conclusions can be extrapolated to the rest of the country, and perhaps even to other countries. The coal found in the Alberta plains is particularly attractive because of its low cost and low sulphur content. Yet coal is no longer the fuel of choice, and a long-standing provincial government policy to favour coal for electricity generation has been ignored for more than a decade. Considering the lack of good alternatives, it seems obvious that we should look to coal as our primary energy source in the generation of electricity and for other industrial applications. This paper discusses some of the reasons that coal has fallen out of favour, particularly with respect to electricity generation. The significance of the deregulation of the electricity industry will not be ignored. In addition, the author will offer his opinion on the question of what it will take in order for coal to once again become the favoured fuel.

May 1, 2001