Search Documents

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By Antonio Fontana

"Environmental problems encountered with the use of diesel equipment in underground mining operations are discussed. The concept and procedure o implementing the Health Effects Index equation as a means of quantitatively assessing an underground working environment is outlined and sample calculations are present ed. Advantages and disadvantages of utilizing this method are also discussed.IntroductionWith the introduction of diesel-powered mining equipment in the 1960s there arose several question s for the environmental engineer to consider. These included: 1. What are the constituents of diesel exhaust and how can they be detected and evaluated?2. What are the toxicities and long-term health effects of these constituents?3. What is the ventilating volume required to maintain the concentration of these constituents below toxic levels?Diesel engines are a class of reciprocating, internal combustion engines in which relatively high compression ratios are used to generate high air-charge temperatures, which cause ignition of fuel to occur spontaneously. Ideally, perfect combustion of the fuel would produce an exhaust consisting solely of nitrogen (N2), water (H2O), carbon dioxide (CO2) and oxygen (O2). However, because no combustion process is perfect, relatively small quantities of imperfect-combustion products, or pollutants, are also generated. These include hydrocarbons (HC), carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), carbon (C) or soot, and sulphur dioxide (SO2).Currently, the Regulations for Mines and Mining Plants, made under the Occupational Health and Safety Act (Section 176), stipulate that weekly tests shall be made to determine the carbon monoxide (CO) concentration in the undiluted exhaust and at the operator's position, and the nitrogent dioxide (NO2) concentration at the operator's position. Also, the aldehyde (as HCHO) concentration in the atmosphere, at the operator's position, is to be measured at least every three months. Threshold limit values (TLVs) have been established for each of the three combustion products, and each is regarded as a separate entity. Consequently, this does not allow for consideration of interactions and possible synergistic effects between the various exhaust components."

Jan 1, 1982

By Brian McIntrye, Bo Trygg

"The need for grinding mills of ever increasing capacity and greater feed openings has tended toward mill trunnion diameters being beyond the size limits for roller bearings.Hydrodynamic plain bearings need to be wide enough to achieve the necessary bearing pressure in order to obtain an oil film with sufficient carrying capacity at low rotational speeds. This greater width increases edge loading resulting from the deflection of the mill under load.Because of the high surf ace pressure involved, the life of support rollers and girth rings is often inadequate-fatigue leads to flaking on the contact surfaces. Heat treatment of the girth rings also has its problems.The hydrostatic shoe bearing permits unlimited trunnion diameter and a high carrying capacity. The self-aligning shoes compensate automatically for radial deviations and large deformations can be tolerated at the girth ring.The sliding surfaces are completely separated by oil under pressure, enabling negligible starting torque and good damping capacity to be achieved together with low rotational speeds.IntroductionHydrostatic bearings have been known within machine technology since 1865, when the Frenchman Girard received a patent for such a bearing. During the following 75 years, these types of bearings were used sporadically for thrust bearings, primarily in water turbines. The first usable radial bearing was not designed until 1938. Since the 1950s, when hydrostatic bearings started to come into use within the field of machine tools, extensive research and development work has been carried out at various institutions and research centres throughout the world. Many support problems are now solved by means of hydrostatic plain bearings and the primary factor in deciding to use them is their unique characteristics:• ability to carry high loadings• no starting torque• large damping capacity• no wear• large running accuracyThe hydrostatic shoe bearing has been developed specially for use in the heavy machine industry, with the requirements for high loadings and large support diameters which this market demands."

Jan 1, 1982

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By Paul G. Dunn

The planning of underground mines is a complicated process involving geological, engineering and operational constraints. MIRARCO is in the process of developing a 5D Mining Exploratorium where 3D mining models are combined with time (4th dimension) and costs (5th dimension). The mining exploratorium is a collection of external and inhouse software packages specifically geared to help underground mining companies arrive at better mine plans. This paper discusses the progress made in the development of the 5D Mining Exploratorium and a change in mine planning philosophy by conducting frequent audits in a Virtual Reality Laboratory. The development of genetic algorithms for optimising stope sequences is also presented.

May 1, 2003

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

By R. O. Grieve

"IntroductionCALEY (1945) and Evans (1950) pointed out that certain instances of convergence between Devonian and Silurian horizons, frequently evident in wells drilled for oil and gas in Ontario, appear to be related to local thinning of salt beds in the Salina formation and they suggested that leaching of the salt beds may have occurred. Exploratory drilling by Imperial Oil Limited since 1945 has brought to light several examples of structures similar to those discussed by Caley and Evans. The writer has had the opportunity to examine cuttings and data from wells which penetrated these structures and the attempt to interpret them in the light of the theory of leaching and subsidence proposed by Landes ( 1945a) to explain the marked brecciation and deformation of Upper Silurian and Middle Devonian sediments which crop out in the Mackinac Straits region of northern Michigan has led to the observations presented in this paper."

Jan 1, 1955

By R. W. Luhning, S. D. Gittins, J .. A. Haston

"The Underground Test Facility (UTF) project operated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) north of Fort McMurray has achieved marked success in field testing mining access and horizontal well in situ recovery of bitumen from the Athabasca oil sands.Mine access has provided for effective placing and operation of horizontal wells in the oil sands from a tunnel system in the underlying limestone. Performance of the in situ recovery process, Steam Assisted Gravity Drainage, has substantially exceeded forecasts made at the start of the project. Over-all results of the program to date show great promise for horizontal well in situ technology as a competitive source of bitumen from Alberta's vast oil sands deposits. The potential economics of a commercial expansion at the site are reviewed in this paper.IntroductionIn situ recovery o f bitumen from the Athabasca oil sands has puzzled the oil industry for many year s, but a breakthrough appears close at hand. The Underground Test Facility (UTF) project initiated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) has had notable success in the piloting of horizontal well processes, which offer prospects for commercial development even under the highly competitive situation facing the Canadian industry . This paper describes the project briefly and presents the potential economics of commercial development on the UTF lease."

Jan 1, 1990

By L. J. Visentin, J. G. Rickaby

"Audiometric testing is a key element in hearing conservation in the mining environment. This paper gives the history of the audiometric testing program carried out by Inco Metals Company, including the program objectives the personnel and equipment involved, calibration and testing, the test procedure, and the classification and evaluation of the test results.IntroductionThe operations of the Ontario Division of Inco Metals Company are located primarily in the Sudbury District. They also include a refine ry at Port Colborne and a mine and concentrator at Shebandowan near Thunder Bay.The company operates nine underground mines, and one open pit, while maintaining six underground mines on a standby basis. Ore from these operations is processed in four concentrators. The metallurgical facilities include a smelter, a matte processing plant, a copper refinery, a nickel refinery and an iron ore recovery plant at Sudbury, and a nickel refinery at Port Colborne. Inco Metals currently mines roughly 9,000,000 tons annually and produces IS elements.Excessive noise in the work place has been a serious problem in the mining industry since the introduction of compressed-air-powered machinery in the last century. At the same time, growing levels of noise inherent in our social environment can threaten the hearing of employees and their families.Only in the last 20 years, however, has the extent of this problem and its implications for people working in the industry and their families been recognized. Since the industry has become aware of the situation it has taken steps to implement comprehensive noise reduction and hearing conservation programs."

Jan 1, 1982

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By J. Boulton

"Nuclear energy is an established and proven energy source. Today, CANDU-PHW nuclear-electric generating stations produce over one third of Ontario's total electrical supply: safely and economically. In many parts of Canada, where economic hydro resources do not exist or are fully developed, coal and nuclear energy are the only alternatives for future large-scale electrical generating capacity.Recent analyses have suggested that, in the f ace of increasing energy demands and decreasing reserves of hydrocarbon fuels, Canada must depend on electricity to provide an expanded fraction of its energy budget. Nuclear energy is likely to play an increasing role in the generation of electricity; there are also potential applications as a supplier of process heat in industry and in the in-situ recovery of bitumen fro m tar sands.The future supply of nuclear fuel, reactor safety and radioactive waste management are briefly discussed. In each case, the benefits to be gained from a controlled expansion in the use of nuclear energy outweigh any uncertainties which may exist."

Jan 1, 1981

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By G. K. Rutherford, G. W. Van Loon

"Tailings in the mining and smelting industry are reject products of the refining process which are deemed too deficient in native are to warrant smelting. They are essentially finely ground rock materials which have been moved by alluvial suspension from the site of crushing to a deposit site. It is realized that components of flotation chemicals used in specific gravity separation may become part of the tailings and also that sewage sludge or other materials may be added at some stage to the tailing deposits.It would seem, then, that as tailings have a similar parent material to soils, namely rocks, and that they have also been comminuted to similar size fractions, they would react in similar ways to soils. There is an increasing body of evidence and experience which both supports and negates this supposition. It is the object of this paper to point out similarities and contrasts between these two materials which may influence the vegetation and rehabilitation of tailings.Soil-Formlnq FactorsThere are considered to be six soil-forming factors which impart the particular and unique properties harboured by a soil at any site. It is .relevant to consider each of these in turn, as each provides an historically based parameter with which to judge tailing properties.Parent MaterialsAlthough all mineral soils have originally come from rocks, for most soils the route has been rather circuitous. Soils may be formed directly from underlying rocks, as in some parts of tropical and semitropical regions today; these are sedentary soils. However, most soils of the world have been formed by materials which were transported to their present site by ice, water or wind, or as volcanic ash. Virtually all soils in Canada have been transported by ice or water and deposited on an extraneous rock surface during the last glacial retreat. Ice-deposited materials are extraordinarily heterogeneous in their size components and may range from very bouldery and gravelly to predominantly clay-sized materials. Water deposited sediments are usually homogeneous, but nevertheless these also show considerable level variations. In many parts of Canada, clay-sized materials deposited in ephemeral post-glacial lakes form the parent material for soils."

Jan 1, 1982

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By John E. Udd, Peter Leinberger, Roman Kozarycz

"This paper is based on work done by the authors in a study of the structural features at a quarry excavated in Chazy limestone on the Island of Montreal. Observations on failures on the quarry walls and benches were recorded, and back analyses of small-scale failures were carried out, thus enabling an assessment to be made of the in-situ strength properties of the rock. Using this information, and data from shear tests in the laboratory, the authors made an analysis of the stability of the south wall of the quarry.IntroductionQuarrying, and excavating for foundations, in the Montreal area involves the removal of million s of tonnes of rock on an annual basis. Even when compared with the quantities mined at major open-pit mining operations, the production figures are impressive. At present, for example, crushed stone is produced at almost 20 quarrying operations either on, or near, the Island of Montreal. The annual capacities of the larger quarries are in excess of one million tonnes each. Lesser, but still substantial, production is achieved at the smaller quarries.Excavations, for foundations , especially during periods of peak construction activity, must also involve large quantities of rock . The writers, however , are not able to produce an estimate of the actual annual tonnages originating from excavations."

Jan 1, 1981

By S. Pinard, A. Desbiens, R. del Villar, D. Jakelski

"During the fall of 1993, a new Pill-based control strategy was installed in the B grinding circuit at the Kidd Creek Division of Falconbridge Ltd. The control strategy was first evaluated on a grinding circuit dynamic simulator (DYNAFRAG), which permitted the discrimination between more than a dozen possible control alternatives. Once the final choice was made the necessary instruments were purchased and installed. The control strategy was configured on the plant computer and is planned to be commissioned shortly.This paper summarizes the control strategy, the design procedure, the installation and the controller tuning. Some preliminary problems posed by the process prior to implementation are also presented.IntroductionIn 1990 the GRAIIM (french acronym for Research Group on Computer Applications to the Mineral Industry) of Laval University started a research project on Knowledge Based Automatic Control (KBAC). This project is sponsored by a consortium of eight mining companies under the umbrella ofMI1EC (Mining Technology Council of Canada), the Quebec Mining Association (AMQ), CANMET and the Centre de Recherches minerales (CRM). The project also benefits from important grants from the Ministere de l'Education Superieure et de la Science and the NSREC-CRD program.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged."

Jan 1, 1994

By Desmond M. Levins

"Australia has almost twenty per cent of the Western World's low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s.Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. IntroductionAustralia is entering a new phase in uranium mining and milling activity . In the first phase of operations, between 1954 and 1971, about 10,000 tonnes of yellowcake was produced at five locations. Most of the production came from the mines at Rum Jungle in the Northern Territory and Mary Kathleen in Queensland. In the 1960s, the demand for uranium slumped, and much of the yellowcake produced at Rum Jungle was stockpiled by the Australian Atomic Energy Commission. The early uranium processing operations in Australia were typical of overseas practice at that time. Environmental problems were generally given low priority and pollution control measures were unacceptable by today's standards. There was little or no recycling of process water, acid waste streams were not neutralized and tailings dams were poorly designed. At Rum Jungle, oxidation of sulphides in waste heaps, tailings dumps and ore stockpiles subsequently led to destruction of vegetation and heavy metal pollution in a nearby river.In the early 1970s, major uranium deposits were discovered in the Alligator Rivers region of the Northern Territory. Significant orebodies were also located in the Great Artesian Basin in South Australia, in calcrete formations in Western Australia and at several locations in Northern Queensland. According to latest available estimates. Australia has about 160/0 of the Western World's uranium recoverable below $US 80 per kg U. Mining these orebodies will require pollution control measures more stringent than practised previously in Australia."

Jan 1, 1980

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976