Search Documents

By S. Harshaw, C. Doyle, A. E. M. Warner, D. Stremlaw

"In the Utility Nickel furnaces, the hearth and sidewalls are lined with high-Al2O3 bricks. During charging and thermal cycling (more so as the linings on these reverberatory furnaces age), pieces of brick spall or abrade from the refractory and collect on the top of the bath. These pieces are removed using a non-corrosive slag toward the end of the heat when the bath temperature is ~1600°C.This benign liquid can be generated by two methods. First and most obvious, suitable ingredients can be pre-mixed so that the flux (flux A) is isochemical with the non-corrosive slag. All that is needed to produce this targetted slag is heat. Second, in other proportions (flux B), the pre-mixed ingredients generate a corrosive slag that melts completely at -1200 °C and corrodes some but not all of the brick particles on the bath surface. As the reaction progresses, the slag changes composition eventually attaining the targetted benign composition. Using this option, additions are monitored to avoid overfluxing. In both cases, the generated slag/brick mixture can then be rabbled from the furnace. This practice has been successfully used for over two years and has been a factor in extending Utility Nickel furnace life to its current levels (about25% increase)."

Jan 1, 1993

By G. S. Hume

THE Plains of east-central Alberta herein described embrace an area from Viking east to the Saskatchewan boundary and from North Saskatchewan river south to Coronation and Monitor (Figure 1). By far the greater part of this area is deeply drift-covered, and .outcrops of bedrock are relatively few and often widely separated. Within the area there are large morainal hills and others of considerable extent that superficially have all the characters of morainal hills but contain a core of bedrock. These latter, then, were hills when the ice sheet traversed the country and only have been modified by glacial agencies. In many places on them, the drift is but a thin veneer, as is certainly the case in part of the Neutral hills (Figure 2) northeast of Coronation and north of Monitor. In other cases, however, as in the Blackfoot hills, southwest of Lloydminster, the drift is sufficiently thick to conceal practically all the bedrock and in many places no information is available as to whether a bedrock core, representing a pre-glacial hill, is present. There is no question, however, that the larger river valleys, as for example those of the North Saskatchewan and Battle rivers, are in part at least pre-glacial. Proof of this can be demonstrated in many places, because obviously the valleys must have been present in pre-glacial times to allow glacial deposits to have accumulated in them. It is also known that inter-glacial deposits occur. At one locality in Battle River valley, in sec. 30, tp. 45, range 2, west of the 4th mer., the following section occurs( l ): 15 feet of boulder clay with granite and other boulders. 56 feet of stratified sands, clays, and gravels containing pebbles of Precambrian rocks and fresh-water shells. From this it is apparent that the 56 feet of stratified sands, clays, and gravels must have derived their Precambrian pebbles from a previous glaciation of which the overlying boulder clay represents another ice advance in this area. Thus, although the river valleys contain glacial and interglacial deposits, they have not been filled by them to such an extent that the drainage has been diverted, and in many places, especially in the case of Battle river and some smaller streams, the size of the valley is altogether out of proportion to the size of the stream it now contains.

Jan 1, 1937

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, Gary O’Connell, Denis Shishin, Jeff Chen, Francis Letarte

"Knowledge of slag properties is required for the optimisation of smelting operations. The phase equilibria and viscosities of the Al2O3-CaO-FeO-Fe2O3-MgO-MnO-NiO-Cr2O3-SiO2 slags at conditions of interest to Koniambo Ni-laterite smelting operations have been investigated. High-temperature re-equilibration phase equilibrium experiments of industrial slags followed by rapid quenching and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) have been undertaken in the olivine and pyroxene primary phase fields at temperatures between 1475 and 1600°C and SiO2/MgO weight ratios between 1.57 and 2.09. Phase equilibria predictions were performed using FactSage thermodynamic software. A slag viscosity model available in the FactSage thermodynamic package has been used to calculate the viscosities of the liquid slags. The Einstein-Roscoe equation combined with the predicted phase equilibria data have been used to estimate the viscosities of the slag slurries (slag + solids). The information provided can be used to assist in the evaluation of the furnace performance, to assess further optimisation of slag composition and to explore possibilities of targeted feed changes.INTRODUCTION One of the key steps in the production of ferronickel from nickel laterite ore at Koniambo Nickel SAS involves reduction and smelting of pre-dried nickel-bearing saprolitic ore (high Mg and Si) in an electric furnace at temperatures up to 1650°C. The characterisation of the slag properties as functions of key operational parameters, such as, temperature and composition, including liquidus, the proportions of solids and viscosity, is essential for improving control and optimisation of the operations. The slag produced in the smelting process is a complex oxide system with the major chemical components including Al2O3, CaO, Cr2O3, “FeO”, MgO, “MnO”, “NiO” and SiO2. Characterisation of these multi-component systems using a solely experimental approach becomes increasingly complex as the number of components is increased."

Jan 1, 2017

By Henry C. Knight

A number of improvements in the techniques of budgetary control have been developed in the 1970's. The most significant of these is zero-base budgeting. This procedure is a marked improvement, because it overcomes some of the key weaknesses inherent in most traditional approaches to budgeting. It incorporates techniques and disciplines which improve the quality of both the budgeting effort itself and the documents that most senior managers will need to evaluate. The end result is a budget that establishes and improves cost effectiveness. This budget is based on resource allocations using cost-benefit criteria and on a system of prioritization for making funding choices. Zero-base budgeting is applied only to costs and expenses that are not conducive to control using industrial engineered standards. Therefore, the benefits attributed to zero-base budgeting will only hold true for administrative, selling, exploration, safety, fire protection and overhead, and other indirect types of costs and expenses. It is in this context that the question of its attractiveness for the mining industry is dealt with.

Jan 1, 1978

By M. G. Lipsett

"Mining properties are becoming increasingly remote, a challenging situation for operating and maintaining equipment. Logistics of transporting workers and materials can be alleviated by having timely, accurate information of equipment location and operating condition, and by automating some activities. This paper discusses an infrastructure for remote operations, with strategies for communicating different types of data, and a design method so that systems can interact with either an operator or another system. A remotely operated excavator prototype is described, with on-board performance and diagnostic monitoring systems now used on production equipment. IntroductionSyncrude Canada Ltd. operates an openpit oil sands mine near Fort McMurray, Alberta. For twenty years, draglines and bucketwheel reclaimers have fed conveyors that transport dry oil sand to an extraction and upgrading plant. In converting to a truck and shovel operation, Syncrude has developed slurry pipelines and bitumen froth pumping to allow more remote leases to be mined more than 30 km from the base plant.There are organizational and resourcing challenges in operating and maintaining equipment in three nearby, but separate, mines. The logistics of transporting workers and materials to production and support equipment become more difficult, and operations and maintenance personnel and facilities become more distributed. Supervising mine operations will rely even more on having timely, accurate information about equipment location and operational status.Syncrude is typical of an open-pit operation. Voice communications are the preferred way to exchange information for making immediate decisions about operations and maintenance. A large number of narrowband FM broadcast radio channels keep teams of miners working together. Haul truck drivers, shovel operators, and dispatchers talk on one channel while maintainers coordinate activities with the control tower on another. Cellular phones have become popular for supervisors who have to talk with planners and engineers in offices without radios."

Jan 1, 2000

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By M. Hardy

"The structural design of mine headframes is challenging due to the significant differences in the geometry, rigidity, and behaviour of these structures compared to conventional buildings. The differences are related to the main purpose of these structures, which is not human occupancy, but rather the support of hoisting equipment. The main objective of this paper is to present the seismic elastic behaviour of headframe structures in comparison with conventional buildings, which is the base case for the definition of seismic loads. This paper highlights the impact of backlegs on the dynamic behaviour of mine headframes, more specifically the resulting torsional sensitivity. INTRODUCTION The design of industrial structures is often governed by industrial processes rather than by architectural constraints. In ground-mounted hoisting plants, the structural configuration of headframes must allow clearances around conveyances and ropes while resisting the lateral loads associated with the hoisting equipment. Typically, these structures use backlegs to withstand the lateral loads, which leads to highly irregular structures with unconventional dynamic behaviour. The codes and standards applicable to the structural design of mine headframes in Canada are often incomplete or not adapted to the reality of practising engineers. This situation creates confusion, and engineers must look at various guidelines and international standards to support the engineering calculations required for the design of these structures. The loads resulting from the support of hoisting equipment, such as ropes and conveyances, are usually simple to calculate and are determined based on the information from manufacturer and industry related guidelines. Moreover, the loads associated with snow accumulation and wind are calculated applying the same methodology used for conventional buildings, without any major issues. On the other hand, the seismic loads are often difficult to calculate based on the methodology from the National Building Code of Canada due to the significant differences in the dynamic behaviour of the structures. The resulting structures may be either over-designed or worse, under-designed. Hence, there is a lack of uniformity in engineers’ designs. The latest edition of CSA S16-14 “Design of steel structures” includes Annex M (Informative) “Seismic design of industrial steel structures” to help designers close the gap between the requirements of traditional regulations and actual engineering practice."

Jan 1, 2019

By E. G. Joe

"Recent trends in Canadian mineral processing were reported in seven areas of interest covered by seventeen technical papers at the 1976 Annual Meeting of the Canadian Mineral Processors, held at Energy, Mines and Resources' Camsell Hall, Ottawa. New milling equipment included the Enviro-Clear thickener, large-volume Outokumpu flotation machines and abrasion-resistant polyurethane screens. Grinding experiences from a variety of milling operations were reported. Opportunities for increased sizing and grinding efficiency were presented. Flotation control by digital computer and by chemical additions were described in two mill operations. Slurry pumping and sampling techniques were described for various operations. Environmental control in milling was reported concerning dust suppression, arsenic removal and tailings disposal. Several aspects of gold milling were described by the most recently commissioned gold mine and by CANMET. Potash operations were reported showing the similarity of processing and process control to that of metallic minerals."

Jan 1, 1976

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982

By A. S. Bayne

WITH the great increase in the use of power-driven machinery in industry, and consequent large-scale operations, the hazards to which , workmen are exposed have become much more numerous than at the beginning of the century. This is especially noticeable in mining. In the past thirty years or so, improvements in methods of excavation and metallurgy have made possible the exploitation of deposits which would have failed to make ore in previous years. This improvement, together with the in-creased use of machinery, has facilitated the mining of tremendously greater tonnages with a marked decrease in unit cost of production. This 'speed up' in mining creates numerous problems demanding close attention of operators and necessitates careful prep;tratory planning, as well as diligent supervision of actual operations. Underground openings increase in size so fast, and all phases of mining, mucking, and transportation proceed at such a rate, that a short period of reduced vigilance on the part of operators . results in disaster, both from the standpoint of safety and economies. Happily, the challenge of increased hazards has been successfully met by a general application of the slogan 'Safety First'. Today, we have large manufacturing concerns devoted entirely to the development and production of safety equipment for the protection of workmen in various branches of industry. Machinery manufacturers, in co-operation with their mining customers, have included the best possible in foolproof devices in the manufacture of hoists, compressors, boilers, electric motors, and equipment of all kinds. Mining companies and private individuals spend thousands of dollars and devote a great deal of time to research with the single object of preventing accidents and combating miners? diseases. Governments throughout the world have written regulations into their statures for the protection of miners and operators. Staffs are appointed to enforce these laws and investigate accidents to ascertain means of preventing them for the future benefit of the industry.

Jan 1, 1938

By Stanley Davidson

Introduction The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oyster-shaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than fifty years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis. The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass which, however, is here concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling. The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proven to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the "Edison' shaft never reached bed-rock.

Jan 1, 1946

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By B. Surender Mohan

Mother Earth being a treasure of minerals, it is prime duty of the mankind to preserve this natural source to ensure steady growth of the nation. Utmost care is to be taken to see that these natural resources are explored and exploited scientifically in a sustained manner to ensure that the resource base improves and last longer. In this backdrop, the topic of ?Lignite - its resource and technology options to exploit deep seated deposits? is an apt subject to be deliberated upon in the present context, where the shallow deposits may slowly get dwindled. I shall deliberate upon the resource base of lignite, production profiles of the last five decades, consumption pattern, demand / supply projections, future available technology options to exploit the deep seated deposits, growth trends of the sector etc. in my paper. With the available resource base and future technology options, I can confidentially make a statement that ?lignite will remain as cocontributor along with coal to India?s energy generation and may well maintain its same status in the 21st century too, as it has been in the later part of the twentieth century?.

Aug 1, 2013

By D. Shen, J. Cheung

Variable reactance arc control by the SPLC (Smart Predictive Line Controller) has been installed at many different mining sites and steel processing plants around the world. Since its first installation 18 years ago, many advances have been made to both the technology, and to its integration with furnace processes and plant operations. The SPLC has helped to improve electric arc furnace stability by reducing electrode movement while maintaining flat line arc power. Stable furnace operation at higher average power increases productivity. This paper summarizes the progression of electro-technology at Hatch since the 1970s, including fixed and variable reactance, digital electrode regulation, and fast variable speed hydraulics for Soderberg electrode, as demonstrated and benchmarked through projects and lessons learned over the years.

Jan 1, 2015

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca's Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By J. A. Vezina

The effects of particle size distribution on metal extraction have been determined from pressure leaching Renzy Mines Limited concentrate with oxygen. Using a pulp density of 30 per cent solids, an oxygen pressure of 80 psig, a temperature of 230°F, a grind of 2.5 hours and a retention of 8 hours resulted in the almost complete dissolution of the nickel and the cobalt and the decomposition of over 96 per cent of the chalcopyrite finer than 20 microns. Only 11 per cent of the chalcopyrite coarser than 20 microns was reduced to smaller than 20 microns.

Jan 1, 1973

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By A. S. Eve

The detection of magnetic dykes by using magnetic variometers is the oldest application of. geophysics to mining, and is also one of the more simple and certain methods 0f locating such deposits. As a result of recent improvements in the instruments, it is now possible to find the dyke, deter-mine with magnetic variometers its strike and dip', with fair accuracy, and to estimate the approximate depth of overburden when there is no outcrop. The application of electrical methods may be used to distinguish mineral from diabase dykes. The authors have had an opportunity of making surveys with the modern Askania types of vertical and horizontal variometers over magnetic dykes in the Sudbury region. The interpretation of the results has been confirmed by diamond drilling in some cases, and by experiments over models. The variometers used were the standard form of Askania instruments (1). The sensitivity of the horizontal type was 17.2 gammas per division, and that of the vertical variometer double this quantity. To make a preliminary survey of the district, parallel lines were laid off two hundred feet apart running north and south, and readings were taken with the vertical variometer every 100 feet along these lines. This can be done very rapidly, and when an indication of a magnetic deposit is found, the readings may be taken every hundred feet, or less if the size of the deposit warrants smaller intervals. If the deposit is a vein or dyke, the readings along the adjacent lines immediately indicate the strike of the body. Thus the presence and strike of a magnetic dyke, whether of mineral value like the pyrrhotite and nickel deposits of the Sudbury district, or simply a worth-less diabase dyke, is simply and rapidly found.

Jan 1, 1932