Search Documents

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of variables, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly, H. Khadivinassab

A combined experimental / numerical approach is proposed to investigate the bulk transfer of solute due to liquid metal feeding during shape casting of aluminum alloy A356 (Al-7Si-0.3Mg). A dumbbell-shaped experimental casting geometry has been developed, which promotes solute redistribution due to liquid metal feeding. The redistribution of solute in trial castings is evaluated based on the area fraction of eutectic phases. In the numerical model, silicon species segregation during solidification are calculated assuming the Scheil approximation, and are coupled with macro-scale solute transport due to Darcy flow in the mushy zone and feeding flow. The model has been implemented within the commercial CFD software, FLUENT, which simultaneously solves the thermal, fluid flow fields and species segregation on the macro-scale. The experimental and numerical results are compared and contrasted to examine the effects of liquid metal feeding in this casting.

Jan 1, 2014

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By L. Yacher

Most metallurgical plants already have sophisticated control systems as well as a process-historian that manage thousands of real-time and historical variables. There exists a huge potential for operational improvement through the inference of patterns, correlations and cause-effect relationships within these records. The ability to run online and offline advanced multivariate statistical analyses represents a great potential for the mining industry, in various areas such as cathode quality improvement in an SX/EX plant, the analysis of the correlation between the ore characteristics and the mill throughput, the determination of early failure alerts for major equipment, etc. The background theory is described, as well as some practical experiences of operations in Chile and Peru. Cu2007

Jan 1, 2007

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By Newell G. Alford

COAL companies are definitely becoming conscious of the need for better organization. Mechanized mining and the intricate preparation of coal have brought with them the demand for better trained and more highly skilled mining personnel. Refinement in coal mine management is increasing the demand for young graduate engineers to start in the lower grades of the reorganization and prepare themselves to meet rapidly increasing coal mining responsibilities. The interest is wide in scope and extends from self-helps, extension work, and management study at the mines to stimulation of interest in coal mining amongst undergraduate mining students, leading to their permanent employment after graduation. Data by the United States Bureau of Mines show the total annual value of coal production (bituminous and anthracite in the U.S.) through the past 22 years as being more than 38 per cent of the combined value of all ocher mineral industry products. Natural-gas production has gained rapidly on coal since 1916; petroleum exceeded coal beginning with 1934 (see Figure 1). For this 22-year period, the Committee on Student Interest in Coal Mining, in the A.I.M.E., made a survey of the mining schools in Canada and the United States to show the approximate absorption of young graduate mining engineers by the coal industry. In 1938, 232 mining engineers were graduated as compared with 42 in 1918 (a war year) and 180 in 1923. From 1923 to 1929 the graduates declined to another low of 90, but from there on there was a rapid annual increase in the graduating output, reaching a total of 232 in 1938 and continuing upward to a maximum of over 325 graduating this present month.

Jan 1, 1940

By D. A. Trotter

"This paper traces the main advances in mine lighting from neolithic times to the 1960s. The earliest lights consisted of reeds or strips of wood soaked in grease. As man's knowledge increased, the oil lamp, the candle, kerosene, acetylene and finally electricity have allowed him to see where no natural light could penetrate. These advances in technology, however, did not come easily. Many false starts were made and great dedication was required by a few lighting pioneers to overcome the many technical difficulties that were encountered. The lighting of coal mines in particular caused unique problems, as there was the ever-present threat of methane explosions. Advances in mine lighting will continue, but these advances are only possible because men like Davy, Wolf, Marsuat and Edison paved the way.IntroductionMan's first efforts at mining consisted of merely picking rock off the surface of the earth. The sun was his only source of light. The early mines of the Neolithic age were simply vertical pits, 5 to 8 m deep. In order to follow an orebody, miners began to dig horizontally from the bottom of these pits, and as work progressed the need for additional light became apparent. With the discovery of the light-giving properties of fire, man was no longer dependent on natural light. Figure 1 gives an impression of the earliest artificial mine lighting used.Early Evidence of Mine LightingCarbonized residue from wood chips which had been inserted into rock cracks can be found in early Neolithic workings. The mines at Krzemionki Opatowski in Poland contain very narrow low tunnels that were lit in this fashion and were worked from 2300 to 1800 B. C. The wood had to burn downward to provide light and because wood burns poorly in this position, the chips were probably soaked in animal fat to make them burn more easily."

Jan 1, 1982

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By Melvin S. Taylor

The environmental control program at Cassiar Mine is an active one involving government, unions and company personnel all working together to achieve a goal- "A clean and safe working environment". This can only be achieved by utilizing three of Cassiar's most important resources; i.e., people, time and money. Past environmental programs have more than proved that the goal can be reached and. with the future programs now in progress. Cassiar Asbestos will achieve its environmental goals.

Jan 1, 1978

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By Naoki Takada, Dae-Sung Cheon, Minoru Sato, Masaji Kato, Manabu Takahashi, Weiren Lin

"The permeability and specific storage of rocks and sedimentary layers deep underground are critical parameters for issues related to the buried evaluation of natural gas and oil, CO2 aquifer storage, various kind of waste storage and so on.The Shirahama sandstone of the Wakayama prefecture, Kii peninsular in central Japan, consists mainly of quartz grains with no cracks and rock fragments that are aggregations of various kind of minerals. The quartz grains have an average size of about 150 micron. The pre-existing pore sizes were distributed dominantly at approximately 1 micron, and the total porosity was about 13%.During the hydrostatic compression test, we measured permeability of Shirahama sandstone by Transient Pulse test for three mutually perpendicular directions. Permeability of Shirahama sandstone remained fairly constant while increasing the effective confining pressure. Permeability anisotropy was observed slightly in the normal and two parallel directions to the bedding planes.We used micro focus X-ray CT with high resolution of 10 micron to visualize and measure the voids space information in Shirahama sandstone. Three-dimensional data were obtained in the intact and stressed sandstone simultaneously. Pore structures and grain boundaries were clearly distinguished. Pore closure and grain movement were clearly observed with increasing confining pressure. Micro focus X-ray CT is an effective tool to visualize and measure the geometrical information in rocks.Three-dimensional medial axis (3DMA) method was introduced to quantify the flow-relevant geometric properties of the voids structure in Shirahama sandstone using µfocus X-Ray CT data. The number of connecting path between two faces, tortuosity and the shortest path distribution within an arbitrary region of Shirahama sandstone specimen were analyzed. Geometrical information on the number of connecting path shows reasonable correlation between permeability anisotropy and mutually perpendicular directions normal and parallel to bedding planes. In addition, we introduced numerical simulation of fluid flow of pressurized Shirahama sandstone by LBM, to discuss the permeability change caused by pressurization on effective confining pressure. We obtained the detailed distributions of fluid pressure and fluid velocity in relatively narrow voids space more than 10 µm. It was confirmed that pressurization effect on permeability caused by the decrease of the connecting path and the shortest path between arbitrary faces, and then caused a complex condition on fluid pressure and fluid velocity."

Jan 1, 2015

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By D. L. Griffith

THE realization by metallurgists of the important effect that traces of impurity may have upon the properties of a metal, and their steady demand for purer and still purer metals, have made the special cools for 'trace' analysis of increasing value. In the United States at least, spectrographic analysis is becoming the standard method for determining the impurities in zinc die-casting alloys. The Hudson Bay Mining and Smelting Company, as a producer of virtually pure zinc, uses the spectrograph to control the purity of its products, and-as the electrolytic method is employed here-to control both the impurities in the electrolyte and those 'trace' elements, which, while they do not contaminate the zinc, have a great effect on the plating efficiency. The general plan of the laboratory is shown in Figure l; the housing for air purification, which is on the roof, is indicated by broken lines. One of the chief factors affecting the layout was the easy way in which a spectrographic assay can be spoiled by contamination. To minimize the quantity of dust tracked in, the laboratory was made separate from the general research laboratories, and an office was placed between the two. This arrangement has its drawback because of the traffic through the office, but it has effectively cut down dust. For similar reasons, the available space was subdivided into a number of small rooms, and the air currents in the laboratory were so arranged that dust would be carried where it would do least harm. Air is drawn in at the roof over a 50-kilowatt bank of Calrod heaters, through Annis air filters, by a No. 4 Sirocco fan. Most of it is forced into the spectrograph room, but some goes to the office and darkroom. The air flow is from the spectrograph room, through the plate-measuring room, into the chemical laboratory, where it is exhausted by a No. 1% Sirocco fan on the fume hood. Air can also re-circulate from the plate-measuring room back to the heater. The arrangement is such that the air in the laboratory is maintained at higher pressure than the outside air; consequently, no dirt enters through cracks about the windows and doors. A thermo-regulator holds the temperature constant within one or two degrees; only on the hottest days in summer does the temperature rise enough to affect the focus of the instrument.

Jan 1, 1940

By R. G. Rosehart, S. Y. Lee

"The current investigation concerns the removal of arsenic from waste waters using ion-exchange resin and activated carbon as sorption media. Use of certain weak and strong base anion exchange resins permits the removal of arsenic. Arsenic may be loaded on the weak base resin in the pH range of 2 to 3 and on the strong base resin above pH 5. The elution of arsenic is successfully achieved using 0.5 M NaCl or a mixture of NaCl and NaOH. The activated carbon investigated was less effective on loading arsenic, but the arsenic loaded was easily eluted by simple pH adjustments."

Jan 1, 1972

By Charlie Harper

Open Pit Mining of Golden Band Resources? EP Gold Deposit Golden Band Resources Inc. (GBN:TSX-V) is Saskatchewan's newest Gold Producer. Located in the La Ronge Gold Belt of northern Saskatchewan, GBN has over 875 km2 of claims with 12 known gold deposits and 4 former producing mines. Production has begun at the Roy Lloyd Mine (Bingo Deposit), to be followed initially by our EP and Komis properties. Development of the underground infrastructure at the Roy Lloyd Mineis continuing and on schedule. Production from these deposits will feed our centrally located and 100% owned Jolu mill. We have our provincial environmental permits in place, and we have an established infrastructure including a 400 tonne-per-day mill, year-round road access, and access to grid power. Construction of the grid power line and the above ground tailings facility are now complete.

Nov 1, 2011

By G. C. Hodgson

Specification and Tests of Rope Wire Chemical Analysis: The range in composition of steel used in the manufacture of wire rope is as follows: Carbon 0 4 to 0.9 per cent Manganese 0 4 to 0.8 Sulphur Not above 0.04 Phosphorus Not above 0.04 The carbon and manganese content are varied according to the gauge of wire to be drawn and the tensile strength required. Generally speaking, best results are obtained from heats where the melt is not of too large a tonnage. The amount of reduction and patenting of the wire is left to the wire maker, who thus has a free hand in meeting the balance of the specification.

Jan 1, 1931