Search Documents

By M E. Watson

Minimising dilution and ore loss is an important part of ensuring profitability of a gold mining operation. White Foil open pit gold deposit is a low-grade deposit and therefore managing ore quality is a high priority. Ground movement through blasting can displace ore and waste boundaries up to 10 m from their in situ location and therefore requires stringent ore movement monitoring and adjustment. There are currently only two options for monitoring blast movement – utilising visual targets (commonly lengths of polypipe) but this has widely been replaced by electronic blast movement monitors (or BMM). Regardless of the technology used, the basic principle is to compare the pre- and post-blast locations of the targets to determine the movement of the rock mass during blasting, which is then used to determine the final location of ore and waste boundaries.The Blast Movement Technologies (BMT) BMM system has been used at White Foil since June 2014. The system has been effective and reliable during that time; however, the annual cost of using the BMM system is greater than other monitoring alternatives. As such, the open pit geology team conducted a study comparing the BMM system against the conventional polypipe technique. The objective was to quantify the profit and loss that would occur based on the ore block transformations from both methods. Eight blasts were selected where polypipes were installed in additional holes adjacent to the BMM monitoring holes. The resulting movement vectors from the respective methods were used to create post-blast ore blocks by transforming the in situ ore blocks. While polypipe is a cheaper alternative, the BMM system tracks ore and waste boundaries more effectively resulting in better quality control, enhanced ability to minimise dilution and ore loss thus maximising profit. For these eight blasts, it is calculated that the BMM system resulted in A$664 978 extra profit through a reduction of ore loss. The total cost of a yearly BMM package was recovered in the first two blasts of this study. The primary reason for the difference is that polypipe had a poor recovery rate of 32 per cent compared with 92 per cent for BMM at White Foil. Therefore, the data used to transform the ore blocks was less representative, resulting in inaccurate post-blast ore block boundaries when using polypipe.CITATION:Watson, M E, 2017. Blast movement monitors or polypipe? A study into cost-effective blast movement monitoring at White Foil gold mine, Western Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S O. Hille

Modern remote mining operations in Australia are more commonly trending towards fly-in/fly-out (FIFO) sites. This trend is driven by numerous factors including increased business centralisation, reduction in operating costs, and a desire to live in coastal cities that offer closer family networks and a greater diversity of facilities. Consequently, the resource development industry has had to adapt. When WMCÆs Mount Keith Nickel Operation commenced operations in 1994, it was developed as FIFO for its entire workforce. Since then, there have been several permutations of rosters within a 21 day compressed work cycle including the 14/7 cycle. This paper discusses a case study of the change in management process to the 9/5 work cycle focusing on minimising fatigue in the workplace. It includes the discussion of the business case, employee reaction and the practical application. The impact of the best practice change after 18 months is discussed.

Jan 1, 2002

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

In March 2003, Rio Tinto Coal AustraliaÆs (RTCA) new Hail Creek open cut coal mine commenced operations in the Bowen Basin. Hail Creek is a two-seam strip mining operation utilising two 90 m3 draglines and a fleet of excavators and trucks to remove the overburden. All overburden at Hail Creek is blasted prior to excavation. The mine conducts its own drill and blast operations while engaging Dyno Nobel for the provision of explosives supply and loading truck (bulk explosives vehicle û BEV) services. This arrangement was favoured over outsourcing the entire blasting function to a contractor. Subsequent to a value engineering review, the mine set about developing and implementing a blasting operation that did not rely on the need to store bulk quantities of ammonium nitrate on site. There were advantages identified in doing this, in particular the reduction of capital expenditure required and reduced exposure to a number of recently introduced security requirements. This approach also makes sense operationally. The establishment of reload facilities for the BEV close to the blasting location, where turnaround times are kept to a minimum, increases the productivity of the BEV. For this strategy to be successful the logistics of ammonium nitrate supply into the blasting operations has to be well planned and thoroughly executed. This means a robust planning and forecasting arrangement needs to be established with the supplier and transporters of the ammonium nitrate. To date, 80 million bcm of overburden has been blasted at Hail Creek and each year the quantity of overburden requiring blasting is increasing. The purpose of this paper is to present the findings of a study: evaluating the effectiveness to date of the strategy to conduct blasting operations without ammonium nitrate storage on site, and identifying whether there is a limit to which this strategy can operate after which the introduction of bulk ammonium nitrate storage facilities are necessary.

Jan 1, 2007

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By Grady B. V, Ault A. R, Newman O. M G, Fraser R. J, Malcolm J. McPhersqn

In all electrolytic zinc plants cadmium is removed as an impurity prior to the zinc electrowinning stage of the process. Cadmium metal is the favoured form of this by-product and most plants use an electrolytic route for its production. The formation of dendrites in cadmium electrowinning processes is the major limitation to deposition rates. There is an economic incentive, therefore, to better understand the factors affecting their growth. A technique that has been used by others to examine fundamental aspects of dendrite growth has been applied to industrial strength electrolytes. It involves potentiostatic deposition in a cell containing the electrolyte of interest. The variation in the current with time at a given overpotential allows the determination of the dendritic growth induction time. A method was developed (the Locus method) from the investigation of a set of such potentiostatic curves, obtained over a range of applied overpotentials, that appears to give a measure of electrolyte quality with respect to dendritic growth in galvanostatic deposition. The Locus technique predicts that zinc at industrial concentrations in cadmium electrolytes should have a significant effect on morphology and that deterioration of morphology will occur as the zinc concentration in the electrolyte is increased. This effect is consistent with literature prediction and was shown to relate to a reduction of the diffusion limiting current density. Magnafloc R333 is used as an additive at Pasminco Metals-EZ to control the morphology of cadmium deposits and the Locus method was successful in predicting its dendrite inhibiting properties. A possible mechanism is discussed. This work has opened avenues for future research with respect to a technique that may have an industrial application in electrolyte characterisation and has pointed to a direction in which better understanding of galvanostatic dendritic growth may be found.

Jan 1, 1993

By Koeng R, Richardson M, Hoare R

A discrete event computer simulation model was developed for two of the stoping methods currently used at the Z.C. Mines Broken Hill oper- ations. The objective in undertaking this project was to provide an effective tool for mine planning and design to allow comparisons of alternative extraction strategies and attempt to optimise the allocation of capital equipment and human resources. The Slam II simulation program was used in conjunction with ,a com- monly used data editor, text editor and graphics package to allow the simulation to be done on a personal computer with minimum training requirements. The computer hardware used was a portable computer cur- rently available using 80386/20MHz electronics. Specific logic techniques were developed to allow the Slam II language to simulate mining opera- tions because it was originally developed for manufacturing and com- mercial simulations. The design of the model was based on observations and a data collec- tion campaign. The model was designed with flexibility which allows simple editing of the input data which includes: - Insitu volumes - Development statistics -Loadout efficiencies -Loader speeds, availabilities and capacities -Chute numbers, volumes, distances and blockage statistics -Trucking statistics -Work schedules -Utility statistics

Jan 1, 1988

By J J. L du Plessis

Escalating energy and electricity costs have become one of the biggest expenditure drivers in mining operations. During the last eight years, energy costs have trebled when expressed as a percentage of total running cost in South African mines. Power consumption on mines is controlled by three main strategies, namely load clipping where energy use is reduced for parts of the day, load shifting where energy use is shifted to other parts of the day, and energy efficiency where energy use is reduced permanently.To reduce the operating costs of ventilating and cooling underground mines continuously, system optimisation studies must be completed. A part of this paper describes methods that can be used to reduce energy usage by optimising cooling and ventilation systems during planning and in existing operations using network simulation models that accurately reflect the current and planned ventilation conditions. These models are used to examine various options for improving the overall ventilation and cooling efficiency. Furthermore, an overview of refrigeration and cooling practices, and ventilation strategies is presented.Ventilation-on-demand and cooling-on-demand strategies have the potential to reduce both the capital and operating costs associated with mine ventilation and cooling systems. In addition, it has been proven that modern strategies and energy-efficient tactics are technically feasible.It is also important that the correct equipment selection is made. This must be based on the best technology with the highest energy efficiency. Where equipment replacement is being considered, energy efficiency must be one of the key decision drivers.In this paper a number of studies were presented and from the experience and the data presented it is clear that a large financial benefit is possible through optimising ventilation and cooling during the planning of mines or within an existing operating mine.CITATION:du Plessis, J J L, 2015. Strategy and tactics implemented to achieve energy-efficient ventilation and cooling of mines, in Proceedings The Australian Mine Ventilation Conference, pp 9–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Most compact bucket wheel excavators in use are in the small to medium range. Large compact bucket wheel excavators compete directly with con- ventional longer boom excavators which have operational advantages over the large compact. There are, however, situations where the large com- pact excavator is viable. In the development of these large compacts there are a number of technical features to be addressed. In addition the SECV now propose to expand the concept to a large compact bucket wheel excavator with a bridge and loading unit for their Loy Yang Open Cut.

Jan 1, 1989

Environmental considerations were key factors in the design of the Ranger Uranium Mines treatment plant. The mine is located adjacent to the Kakadu National Park and has an average rainfall of 1.6m per annum. Initially, no contaminated water or liquid effluents are to be released from the project area and thus water management is a key design and operating fact. Particulate and gas emission criteria influenced design as did occupational hygiene factors (dust, radon, housekeeping, maintenance access). Equipment selection and engineering standards were conservative and resulted in the plant attaining design performance in less than three months from the date of commissioning. A number of mechanical and operational problems were experienced and are discussed in the paper, however none of these problems have had a significant effect on production.

Jan 1, 1984

By Craw D

Quaternary warping and uplift of antiformal schist ranges in Central Otago, New Zealand, has resulted in recycling of alluvial gold from widespread, generally weakly auriferous, Miocene fluvial gravels that unconformably overlie the schist, into aprons of fan sediments along the range margins. Basement erosion during uplift has been limited and so gold input from sparse gold-bearing quartz veins in the schist has been relatively minor. In an eluvial cycle on the slopes of the ranges, chemical remobilization of gold occurs during oxidation and erosion of the Miocene sediments. The typically fine-grained (300-400¦m) gold undergoes chemical modification and grain size enhancement of up to two orders of magnitude, and much of it is redeposited in a large number of relatively small alluvial fans along the range margins. Groundwater mobility within the fans results in minor additional gold mobility and grain size Enhancement.

Jan 1, 1995

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 km NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity.

Jan 1, 1995

Trial ore production began at the Hilton Mine in 1987 with ore being trucked into Mount Isa for treatment at the Lead/zinc Concentrator. The expansion of output from the Hilton mine required additional concentrator capacity which led to the design and construction of the Hilton Concentrator. Systematic laboratory and Pilot Plant testwork dating back to 1968 to develop a flowsheet and reagent regime suited to the varied and generally complex mineralogy of the Hilton ore was successfully concluded with a Pilot Plant trial using a sulphoxy based sphalerite depression system in early 1988.In May 1988, a decision was made to build a 750 000 t/y concentrator with some novel technological and capital-efficient features. The Hilton Concentrator commenced operations in December 1989 reaching target grinding rates and metallurgical performance by mid-1990. Current ore treatment rate is 800 000 t/y.Lead concentrates assaying 43 - 48 per cent Pb are combined with the Lead/Zinc Concentrator lead concentrates and smelted at Mount Isa. Zinc and Low Grade Middlings (LGM) concentrates are filtered in the zinc filter plant at Isa with those from the Lead/Zinc Concentrator and then railed to Townsville for export or treatment in Australia.

Jan 1, 1993

By S Davidge, J Pile, R Schumann, E Kepe, W Stewart, M Ridd, B Rathi

Geographical constraints, including steep terrain and high rainfall, at the Ok Tedi copper-gold mine in PNG’s Western Province present Ok Tedi Mining Limited (OTML) with significant challenges in mine waste management. Waste management includes discharge of tailings into the local river system and storage of waste rock from the mine pit in waste rock dumps which erode into the river system. Copper bearing skarn mineralisation is associated with a massive sulfide (mainly pyrite) deposit. Consequently, waste rock and tailings can contain significant amounts of pyrite. Without appropriate management, these waste streams represent a risk of producing acid and metalliferous drainage (AMD) when discharged to the river system. Throughout the life of the project, OTML have developed evolving strategies to manage mine wastes and mitigate AMD.

Aug 2, 2023

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By B P. Micke

Central Norseman Gold Corporation was established in 1935 and has been mining on the Norseman field in Western Australia since then. It is Australia’s longest continuously operating gold mining operation at nearly 80 years, although it has had its periodic challenges in the intervening years.Over the last 40 years, a series of open pit mines around the Dundas Goldfield have supplied lower cost mill feed to the Phoenix Mill at Norseman from time to time but this has largely come to an end for the foreseeable future. Now that underground ore sources are once again the principal mill feed, there are several challenges to be met for an ongoing profitable operation.During the last 20 years, there have been three different owners and this has affected the manner in which the operations were managed quite significantly. These differing approaches are contrasted and examined in some detail from both the operational and financial aspects.Planning of a downsized operation to ensure sustainable profitability in the future in a mining environment where there has rarely been more than two to four years of reserves ahead of the mill for planning purposes has been a significant challenge. Several of the options examined are described, including alternatives for future mine development.CITATION:Micke, B P, 2014. Managing the margin at Norseman, Western Australia – a case study, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J J. Eksteen

"In the platinum group metals (PGM) industry, smelters are often perceived as ‘black boxes’ that have to process concentrates of variable mineralogy and originating from multiple mines operating along strike or downdip from each other in the same geographical region, as is the case in the Western Bushveld of South Africa. However, PGM smelter complexes are much more sensitive to concentrate blend variation than most metallurgists or geologists would anticipate.This paper will review the impact of concentrate blends deriving from a number of concentrators processing ores from the Bushveld Igneous Complex (BIC) on smelting and converting behaviour and the constraints they impose upon smelter operation. Significant variation in behaviour is not only noted between the main mineralisation types, namely the Merensky and Upper Group 2 (UG2) reefs, but also within a given reef type. Due to the way PGMs are mineralised and finely disseminated, concentrators have to grind concentrates ultra-fine to liberate the PGMs and provide a sufficiently high-grade concentrate for smelting.The chemistry and mineralogy of the concentrates vary with the type of mine (open pit versus underground), the reef type and varies along strike; this variation impacts numerous key smelter parameters such as the base metals content, the matte fall, the converter aisle capacity, sulfur dioxide gas production, furnace matte and slag temperatures, and the accumulation of high smelting chromite-spinel minerals that has led to significant smelter upset conditions such as catastrophic furnace hearth and sidewall failures.Due to the production intensity of smelting, ie its high rate of processing per unit volume, smelters have been found to be far more sensitive to rapid variation in concentrate properties, highlighting the need for adequate blend control.CITATION:Eksteen, J J, 2016. Impact of Mineralogical Variation on the Smelting of Cu-Ni-PGM Concentrates, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Matthew SP, Hayes PC

The product morphologies formed on the reduction of dense wustite crystals are classified into three types,A) porous iron, B) porous wustite covered with dense iron and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed

Jan 1, 1984

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013