Search Documents

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By M G. Millad, M Zammit

The Kipoi Central (KPC) copper project is located in the Katanga Province in the Democratic Republic of the Congo and is presented here as an example of an operating mine where the Mineral Resource was initially estimated by uniform conditioning (UC) and subsequently updated to localised uniform conditioning (LUC). This paper discusses the implementation of an estimate run using LUC and compares the results based on resource definition drilling to those obtained by close spaced grade control drilling and actual mill production.UC is a nonlinear geostatistical technique designed for recoverable resource estimation, typically using wide spaced exploration and resource definition drilling. The primary output of UC is the grade, tonnage and metal above a series of user-defined cut-off grades for a particular selective mining unit (SMU) block size. The UC approach is considered to provide a more accurate representation of the recoverable grade and tonnage at SMU support for non-zero grade cut-offs than would typically be achieved by a traditional linear estimator such as Ordinary Kriging. LUC is a relatively new approach involving the post-processing of a UC estimate and is used to spatially present the grade distribution predicted by UC at the SMU scale.This study demonstrates that the calculation of a more accurate and realistic grade-tonnage relationship for small SMU sized blocks is possible at the exploration stage using LUC, provided that the necessary theoretical and practical conditions for implementation of this technique exist.CITATION:Millad, M G and Zammit, M, 2014. Implementation of localised uniform conditioning for recoverable resource estimation at the Kipoi Copper Project, Democratic Republic of the Congo, in Proceedings Ninth International Mining Geology Conference 2014 , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P M. Ashley, M T. Costelloe

The Mary Kathleen tailings storage facility (TSF) contains 7.1 Mt of uranium mill tailings. This waste repository was rehabilitated in the mid-1980s using a multibarrier dry cover. At the time of mine closure, it was predicted that acid mine drainage (AMD) generation would not eventuate and that uranium, heavy metals and radionuclides would be adsorbed within the tailings and not seep from the TSF into the environment. This study reports on the environmental status of the TSF. Gamma-ray measurements indicate an intact dry cover of the waste repository. However, seepage (~0.5 L s-1) of acid (pH 5.71), saline (0.31 per cent), high conductivity (8.8 mS cm-1), slightly oxygenated (DO 2.6 mg L-1), radioactive waters occurs from the toe of the tailings dam into the former evaporation ponds and local drainage system. Seepage waters are calcium-magnesium-sulfate rich with elevated Fe, Mn, Ni, U and Zn values. Oxygenation of tailings seepages causes the precipitation of Fe and coprecipitation and adsorption of other metals (Pb, U, Y), metalloids (As), rare earth elements (Ce, La) and radionuclides (U-235, U-238, Th-227). In contrast, Ba, Ni, Sr, Mn, P, S, Ca, Mg, Na and K as well as Ra nuclides (Ra-226 and Ra-228) remain in solution until pH neutralisation and evaporation lead to their precipitation in efflorescences and sulfate-rich evaporative sediments further downstream. Dry capping of Mary Kathleen uranium mill tailings has resulted in physical containment of the wastes. The dry cover shows no signs of erosion and radiation levels are within acceptable limits. However, the flow rate of surface seepage from the TSF occurs at a much higher rate than predicted. Also, the neutralising potential and adsorption capacity of the tailings and underlying aquifer were overestimated at the time of mine closure. AMD has developed mobilising metals, metalloids, rare earth elements, alkalis, radionuclides and sulfate from the waste repository into surface water seepages.

Jan 1, 2003

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J Visser

Dust mitigation has long been seen as nothing more than managing a nuisance issue, but the reality is that poor dust management can lead to one or more of the following negative consequences: an increased risk of safety incidents, lost revenue, reduced and possibly even lost licence to operate, regulatory intervention, high staff turnover and/or absenteeism and occupational health and safety (OH&S) issues. Dust mitigation and management is not a black art; rather it is a scientifically driven process that can provide an opportunity to increase profits, increase the companyÆs status as an excellent corporate citizen, enhance staff retention and reduce the safety risk profile of the operation.The way to achieve success in dust mitigation and control is to apply the scientific method to each problem that can arise and plague any operation by using current industry best practice. This method of dust problem-solving can be applied to dust issues arising from specific dust sources and locations. The dust sources can include wind impacting on stockpiles, open areas, tailings storage facilities, moving train and truck loads, vehicular traffic on roads, the operation of shovels, front end loaders, draglines and other equipment, as well as ore movement on conveyors.The solutions will come from a combination of deployment of dust collection equipment, dust and moisture monitoring equipment, the appropriate application of water and chemicals, the introduction and maintenance of appropriate barriers and the use of predictive data from local and public weather stations. The paradigm shift required is to view dust mitigation as one aspect of normal operational practice, not a ænice to haveÆ or æunnecessary expenseÆ as most operators currently view it. This attitude is becoming more important as more and more local communities oppose the development of mines. One of the reasons for this local opposition is the inevitable dusty environment that is usually associated with mining.Dust mitigation is not a significant expense if correctly designed and included into the system, either as part of the original design of the operation or as a brownfield installation after the fact. Indeed, there is always a loss of revenue associated with dustiness resulting from ore movement and avoiding this goes a long way to paying for any associated dust mitigating costs.CITATION:Visser, J, 2013. Dust mitigation - changing the paradigm, in Proceedings Iron Ore 2013 , pp 27-38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

In response to requests from the iron ore mining industry, the Commonwealth Scientific and Industrial Research Organisation (CSIRO) Division of Mineral Physics has developed a number of bulk analysis techniques in which analyses are obtained directly from ore samples weighing many kilograms or from ore located on conveyor belts.Because penetrating neutron and gamma radiation is used, measurements are obtained from a large volume of ore, which ensures thal the analyses are represelllative of the bulk.Two different gamma-ray techniques have been developed to measure iron ore grade. The first is based on backscallering of 60CO gamma rays, while the second involves measurement of the annihilation radiation which arises when the ore is irradiated wilh 226Ra gamma rays. Both techniques measure the iron concentration with an accuracy (1 s) of better than 0.4% Fe.A thermal-neutron irradiation technique using a 252Cf neutron source has been developed for the simultaneous determination of iron and the aluminium impurity (expressed as AI2O3) in iron ore fines on a conveyor bell. Because the conveyor speed must not exceed about 0.05 m/s, if good accuracy for AI2O3 is required, an auxiliary analysis bell is required Lo avoid inLerference with normal ore processing. Dynamic trials have demonstrated that accuracies of 0.6% Fe and 0.1% AI2O3 can be obtained.

Jan 1, 1985

By K Faure

At Sams Creek a peralkaline granite porphyry dyke hosts gold-bearing sulfide-quartz-siderite veins. The granite dyke intrudes Ordovician-Silurian metapelite and quartzite, and has thin lamprophyre dykes along its contacts. The mineralised veins and the granite and lamprophyre dykes have been deformed during several phases of folding, the youngest of which is Early Cretaceous. The granite has been hydrothermally altered, with early magnetite-siderite¦biotite alteration overprinted by sulfide and quartz-siderite veins and quartz-perthite-albitesiderite-pyrite-rutile¦sericite alteration assemblages. The sulfide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, with minor quartz and siderite. The gold contains significant silver (up to 30.8 wt per cent) and ranges in fineness from 692 to 844. Immiscible liquid-rich fluid inclusions, in quartz protected from recrystallisation by enclosing arsenopyrite, contain carbonic liquid that homogenised at temperatures of 320 - 355¦C. The Sams Creek gold deposit is distinguished from the orogenic gold deposit type by its stockwork veining, magnetite-siderite¦biotite alteration, high sulfide content, ore mineralogy and the absence of mineralisation in the metapelite country rocks. Features of the Sams Creek gold deposit do not fit neatly into existing classifications of granite-related gold-bearing deposits. The peralkaline composition of the Sams Creek granite and the absence of molybdenite and paucity of chalcopyrite, are major points of difference with gold-rich porphyry copper deposits. The presence of a lowsulf idation-state ore mineral assemblage, carbonate alteration and carbonic fluid inclusions at Sams Creek are typical of many of the reduced granitic intrusion-related type of gold deposit. However, notable differences are: the reduced type granites are metaluminous and calc-alkaline; and Sams Creek only has high As in contrast to elevated Bi, W, As, Mo, Te, and Sb in the reduced type. The Sams Creek deposit also shows affinities with gold deposits associated with alkaline magmatism, and it appears to be a new variant of this type as an As-Au deposit associated with a peralkaline granite and lamprophyre.

Jan 1, 2004

By Y Li

An ilmenite ore from the Murray Basin was initially characterised using combined X-ray Fluorescence Spectroscopy (XRF), X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Electron Probe Microanalysis (EPMA) techniques. XRF analysis showed the ilmenite sample contained 58.7 wt per cent TiO2 and 26.2 wt per cent Fe2O3. Major impurities included: Cr2O3 (4.5 wt per cent), Al2O3 (2.7 wt per cent), SiO2 (1.9 wt per cent), Mn3O4 (1.5 wt per cent) and MgO (1.1 wt per cent). Manganese and magnesium were present as solid solution components within the ilmenite lattice while the elevated Al2O3 and SiO2 levels were due to separate aluminosilicate gangue minerals. Chromium was associated with discrete chrome spinel gangue phases of variable composition, (Fe,Mg)(Cr,Al)2O4. Quantitative XRD analysis of the sample identified rutile (12 per cent), ilmenite (11 per cent), and pseudorutile (67 per cent) as the main titanium-containing phases and chrome-rich spinels (seven per cent) as the major impurity phase. Minor quartz, aluminosilicates, zircon and monazite were also present. The ilmenite was mixed with synthetic graphite, pressed into pellets and reduced carbothermally in nitrogen at 1200 and 1400°C with C/O molar ratio of 1.2. Titanium oxide in the ilmenite was converted to titanium oxycarbonitride. Iron oxides were reduced to metallic iron. The Changes of impurities as a result of reduction was examined by SEM and EPMA analyses. Iron and chromium oxides within Fe-rich chromite were reduced to form a Fe-Cr-C alloy. Mg-rich chrome spinels were partly reduced at 1200°C. Zircon particles were not reduced at 1200°C, but were significantly reduced at 1400°C, with the particles becoming porous and the silicon being removed.

Oct 5, 2011

By Wilkins C

The Browns Creek deposit is located 8 kin west of Blayney and 220 km west of Sydney (Figure 1), at lat 33¦32'S, long 149¦10'E on the Bathurst (SI 55-8) 1:250 000 scale map sheet. The total measured, indicated and inferred resource at 30 June 1997 was 1.29 Mt at 6.39 g/t gold and 0.45 per cent copper. During the 1996 - 97 year 263 557 t of ore at 6.30 g/t gold and 0.48 per cent copper was treated, to produce 47 496 oz of gold, and 1 169 t of contained copper in concentrate. As the result of an increase in the resources and reserves, because of underground exploration drilling and accelerated mine development, 1997 production at Browns Creek is predicted to expand from 240 000 to 390 000 tpa, to yield more than 70 000 oz of gold per year.

Jan 1, 1997

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

The æMountain Camp reefÆ at Alford's mine, Wakamarina,Marlborough, had no recorded gold production although assays of 5 - 26 g/t were reported, but it did produce c. l000 kg of scheelite. The lode consists of a lower massive quartz layer, and upper, cm-banded, ribboned quartz layers, and has a very low sulphide content. Within the massive layer, relict early fine-grained mosaic quartz with idioblastic scheelite is surrounded by recrystallised granoblastic coarse-grained quartz with calcite and plagioclase, in which an original ribbon banding texture is mimiced by strings of tiny inclusions. In both the banded and massive layers, rounded quartz grains, created by cataclastic milling of grain margins and along syn-vein fractures, have been partially annealed within later quartz overgrowths. Late fibrous quartz and calcite fill brittle cross fractures.   Deformation events D1 and D2 are associated with mid-late Jurassic metamorphism of the Pelorus Group, D2 producing the main regional schistosity (S2, and the earliest scheelite. D3 is an extensional mylonitic shear event that formed the dominant schistosity in Alford's mine (S3). The quartz lode was emplaced within the mylonite by a series of individual dilation pulses (D4). The D5 event caused crenulation of the S3 mylonite, kink banding and chevron folding of the S2 schist and S3 mylonite, and reverse faulting, rodding and cross-fracturing with late fibrous quartz-calcite veining of the D4 quartz lode.   Fluid influxes during successive dilations of D4 fractures progressively caused recrystallisation of earlier quartz bands on the footwall, annealing and recrystallisation of quartz along milled crystal margins and fractures, and deposition of minor sulphides. There was thus a dynamic interplay between fault dilation, lode fracture, fluid influx, lode band deposition, and lode recrystallisation. Illite-Kfeldspar al ¦ 2 Ma (K/Ar), c.30 Ma after metamorphism.

Jan 1, 1996

By A Seneviratne, Y Li, N Udugampola, X Ai, B Li

LoRa (Long Range) is a low-power, long-range wireless communication technology that has gained significant research interest for its potential use in multi-hop linear wireless sensor networks (LWSNs) for underground mines. These networks deploy LoRa-enabled sensor nodes in underground mines, together with LoRa repeaters placed along mine tunnels to relay sensor data to a LoRa gateway, which connects to a backend network for application-level processing. Since the packets generated by sensor nodes farthest from the gateway have to hop through many repeaters, their probability of successfully reaching the gateway is significantly lower due to the higher chance of packet collisions compared to sensor nodes closer to the gateway, resulting in a lack of network fairness for the sensor nodes. In this paper, we first present an algorithm to improve the fairness of a LoRa LWSN by grouping neighbouring nodes and adjusting the number of packet re-transmissions and transmission intervals for each group. Then, we demonstrate that the fairness of a simulated LoRa LWSN can be improved by approximately 500 per cent by applying our algorithm. We verify our algorithm with network simulations under different network traffic levels and grouping strategies, obtaining fairness improvements in each scenario. Our algorithm and results will pave the way towards developing highly fair LWSNs for underground mining applications.

Sep 1, 2024

By Butler I. K, Nicholson P. M

There are four main types of base metal and gold mineralisation recognised in the central Pine Creek Geosyncline. These are stratiform, polymetallic veins, stockwork/concordant gold-quartz veins and unconformity related uranium-gold-platinoid mineralisation. The stratigraphy of the central Palaeoproterozoic Pine Creek Geosyncline has been simplified into three groups comprising the Batchelor, Frances Creek and Finniss River Groups in ascending order. Stratiform mineralisation occurs within the Frances Creek Group. The earliest mineralisation is found adjacent to circular faults ringing basement highs. Higher in the stratigraphy, stratiform mineralisation is often associated with zones of high compression in the vicinity of basement highs. A synsedimentary-diagenetic origin for stratiform mineralisation is proposed. Polymetallic vein mineralisation occurs within the Frances Creek and Finniss River Groups. Its composition changes systematically through the stratigraphy similar to the stratiform mineralisation. The mineralisation is structurally controlled and usually occurs in the vicinity of basement highs. Stockwork-concordant gold-quartz vein mineralisation is hosted by the upper Frances Creek and Finniss River Groups. It occurs within compressional zones and along the Pine Creek Structure corridor around, above and particularly between basement highs. Mineable reserves occur in thick continuous semi concordant quartz-sulphide veins and/or stockworks. Unconformity related uranium-gold-platinoid mineralisation shows a close spatial relationship with the Palaeoproterozoic/Mesoproterozoic unconformity. The mineralisation is localised by structures formed during Mesoproterozoic deposition and is commonly adjacent to Archaean basement or its remobilised equivalents. The type of mineralisation (stratifom/polymetallic vein) is a reflection of local stress regimes, structure and physio-chemical conditions. An initial phase of stratiform mineralisation is postulated to have occurred with the first significant marine transgression in a tensional regime. A second phase occurred later during a compressive regime. "Ihermochemical sulphate reduction of mineralising fluids by hydrocarbons is invoked as the precipitation mechanism for the polymetallic vein type of mineralisation. Hydrocarbon generation is postulated to have occurred within the Frances Creek Group, in many places contemporaneously with the movement of mineralising fluids and basin compression. Polymetallic veins formed from the interaction of mineralising fluids and hydrocarbons which were trapped in suitable structures. An abundant, continuing supply of hydrocarbons was necessary to form significant deposits. Where these conditions were not net, the mineralising fluids largely continued their ascent to the near surface environment to form stratiform deposits. The stockwork/concordant gold-quartz vein mineralisation is a later event and occurred during the relaxation of compressional defonnation after deposition of the 1-inniss River Group.

Jan 1, 1994

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

By C J. Moran

Given that the mining industry is committed to sustainable development principles and that Australia is experiencing changes to the regulatory environment that aim to modernise the water sector and encourage adoption of consistent approaches, there is a well defined need for the Australian minerals industry to develop a water accounting framework. This requires: key terms and definitions for water metrics for use in the Australian minerals industry that is consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current requirements were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (water loss through evaporation is an example). The adopted terms and definitions dictated model development, with the conclusion that a systems approach was the most effective calculation process. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and can be adopted as the first step towards developing national water accounts for the Australian Minerals Industry.

Jan 1, 2009

The Myra Falls minesite, of Westmin Resources Limited, is located at the geographic centre of Vancouver Island, within the confines of Strathcona Provincial Park. The operation includes two active underground mines, II-W and Lynx, together with a modem 3650 1/d milling facility. Recent exploration successes will lead to the commissioning of a third mining area in late-1993 - The Battle/Gap Mine. These ore deposits are complexly metal-zoned volcanogenic massive sulphides of Devonian age, hosted in the Myra Formation of the Sicker Group volcanic assemblage. Three distinct felsic volcanic units are defined within the 450 metre thick Myra Formation. They are, from oldest to youngest, the H-W Horizon, the LMP Horizon and the Upper Rhyolite Unit. Massive sulphide mineralisation occurs throughout the property in the H-W and LMP Horizons. There are a number of orebody types, including polymetallic massive sulphides, polymetallic disseminated sulphides, zoned pyritic massive sulphides, elastic sulphide zones and stringer sulphide zones. Individual orebodies range in size from 10 000 tonne zinc-rich polymetallic lenses to the ten million tonne, zoned massive sulphide H-W main lens. The property has been in continuous operation for 26 years, producing over 13 Mt of ore averaging 2.2 g/t Au, 64.0 g/t Ag, 1.9 per cent Cu, 0.6 per cent Pb, and 5.6 per cent Zn. Current geological reserves stand at 12.5 Mt at a comparable grade, including 4 Mt of recently discovered high grade ore in the Battle and Gap Zones. Mining and milling methods have evolved over time to enable successful extraction and milling of these complex ores. Change is on-going with the recent conversion of the H-W Mine to large-scale bulk mining methods, and the development of effective computerised ore reserve calculation and mine planning tools. These changes, in concert with successful exploration techniques that led to recent high grade ore discoveries, have breathed new life into the operation and should assure its present and future viability.

Jan 1, 1993

By X Zheng, P Manton

Pebble recycle crushing circuit performance at Telfer has historically fallen significantly short of the design product P80 of 12 mm. An investigation was undertaken to evaluate the current pebble crusher circuit performance, quantify the optimum performance achievable with the existing circuit and examine the impact of pebble crusher performance on the overall grinding circuit throughput. The primary objective of this investigation was to develop an operating strategy that could consistently deliver the finest possible pebble crusher product to maximise the overall plant throughput.The pebble crusher specific energy (Wc) was proposed as a key control variable for pebble crusher operation based on the results of plant survey work. Over the range of pebble crusher specific energies encountered at Telfer, a strong linear relationship was found to exist between Wc and the crusher product size. This direct linear relationship between specific energy and crusher product size remained constant regardless of how the change in specific energy was generated, ie through changes to the crusher closed side setting (CSS), feed rate, liner profile or moisture content. Key findings for the Telfer pebble crushing circuit were: each 0.1 kWh/t change in Wc resulted in a 4.9 per cent to 6.0 per cent change in plant throughput, each 1 mm change in pebble crusher CSS resulted in a 2.2 per cent to 2.6 per cent change in plant throughput, and 0.57 tonne of new feed was displaced for each tonne of crushed pebbles recycled to the semi-autogenous grinding (SAG) mill. The presence of an existing 3000 tonne pebble stockpile between the SAG mill and pebble crushers provides an opportunity to manipulate the feed rate to the pebble crushers independently of the SAG mill pebble production rate. This flexibility, along with excess pebble crushing capacity, enables the pebble crusher specific energy to be maximised the majority of the time. Pebble crusher specific energy has subsequently been incorporated as an online crusher control measure to assist in maximising plant throughput.

Jan 1, 2009

By D Morgan, K Jones

"In March 2015 Northparkes Mines (NPM) installed a process mineralogy facility on-site. The laboratory included a TESCAN TIMA scanning electron microscope (SEM) and was the first SEM facility to be commissioned on a mine site in Australia. While the initial intent of the quantitative mineralogy laboratory was to provide information to drive processing plant improvements, in practice, it has been utilised for so much more and is now serving as an integral link between departments on-site. This multidisciplinary approach to orebody knowledge is a new strategy for NPM whereby all parts of the value chain are aligned towards the common goal of achieving process efficiency and stability while still maintaining high throughputs. The NPM experience is presented as a case study to illustrate how on-site process mineralogy can drive a realignment in business strategy with a common goal of mill optimisation, stability and more realistic forecasting through orebody knowledge and information sharing between disciplines.Citation:Jones, K and Morgan, D, 2016. On-site Process Mineralogy - Linking Departments and Disciplines with the Common Goal of Increasing Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 149–156 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By M BSckstr÷m

Acid rock drainage (ARD), commonly found in vicinities of sulfidic mines, possess properties capable of widely affecting the surrounding environment by acidification and heavy metal pollution. In most ARD treatments, various alkaline sources are used to neutralise the acid produced. Utilisation of highly alkaline fly ashes instead of raw materials is a cost-effective alternative, which lately have become increasingly popular. In laboratory batch experiments, neutralising capacity of fly ash was studied during 20 days. ARD was added to the fly ash once a day, for each increment the liquid to solid ratio (L/S ratio) was increased. At an early stage of the experiment (day 6, L/S ratio 12), the concentration of barium in solution unexpectedly increased by a factor of 50 (from 200 to 10 000 ¦g+l-1). This high concentration also sustained the following two days (L/S ratios 14 and 16) before dropping to the original level. pH showed a slight increase during these observations (pH 12.4 - 12.7). The phenomenon was also observed in a parallel and identical series. In addition to barium, aluminium and strontium clearly increased in the same manner, however not as much as barium. Furthermore, concentrations of chromium and molybdenum noticeably decreased at these distinct L/S ratios (12, 14 and 16). The behaviour of barium and subsequently strontium, aluminium, chromium and molybdenum is only partially understood. The decrease of chromium and molybdenum is suggested to be due to incorporation into the interlayer regions of hydrocalumite (Ca4Al2(OH)12(OH)2+6H2O), replacing the hydroxide groups, which also explains the increase in pH. Moreover, the increase of barium, strontium and aluminium could be attributable to dissolution of the silicate mineral celsian (Ba,Sr(Al2Si2O8)). Alternatively, barium and strontium increase could be explained by dissolution of a Ba,Sr(SO4)-solid solution and aluminium increase by dissolution of hydrocalumite or ettringite.

Jan 1, 2008